What did you do to your truck today.The 3rd chapter - Page 42 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**j_cst_10** · 05-21-2020, 08:54 AM

Quote:

Originally Posted by KQQL IT

Fresh coat of penetrol
And some nanoskin wet look tire sauce

Love Penetrol. Just don't lean on it real hard for a couple days haha.

KQQL IT · 05-21-2020, 11:55 PM

Quote:

Originally Posted by j_cst_10

Love Penetrol. Just don't lean on it real hard for a couple days haha.

It's rained on it twice the morning after I put in on.

But it's coming around slowly.
Going to have to paint the roof soon..

**j_cst_10** · 05-21-2020, 09:30 AM

I didn’t know that. Yeah mine was just blue cloth. The boards are all warped anyway so may try the board/cloth pre assembled headliner.

72c20customcamper · 05-23-2020, 05:52 PM

Quote:

Originally Posted by j_cst_10

I didn’t know that. Yeah mine was just blue cloth. The boards are all warped anyway so may try the board/cloth pre assembled headliner.

The cardboard was sagging on mine too. I dampened the top side of it and layed a few paver blocks on it in the sun. Sag came out but most likely will return

SRU1436 · 05-22-2020, 11:16 AM

I drove mine yesterday, I think it developed a vacuum leak. Have to work on that. Otherwise she is doing well.

**ohboy321** · 05-22-2020, 04:32 PM

Cleaned up the 4x4 fan shroud I bought from CUSTOM/10. I used Gunk, de-greaser and a power washer, being careful to not mar the factory finish. Will be nice when installed.

OregonNed · 05-22-2020, 05:42 PM

Quote:

Originally Posted by ohboy321

Cleaned up the 4x4 fan shroud I bought from CUSTOM/10. I used Gunk, de-greaser and a power washer, being careful to not mar the factory finish. Will be nice when installed.

Oooooo that is nice! I just posted a thread about adding one back to mine! Looks like a real score!

67C10Step · 05-22-2020, 09:26 PM

Finally broke down and removed all the heater and controls. I’ll probably be in the hospital due to the hantavirus with all the mouse stuff in there. The outer box was completely full of leaves, acorns, and dirt dauber nests. Good news was the fan motor worked after knocking a pound of mud nests off the wheel. Bad news is the outer box is pretty much shot. Lower left corner is broken and the metal area between the fan and firewall is rusted gone.

SRU1436 · 05-24-2020, 01:27 PM

Replaced all the vacuum hoses, and carb fuel filter. Took it for a test drive and eliminated the rough idle while stopped in drive.

**j_cst_10** · 05-24-2020, 02:20 PM

Quote:

Originally Posted by SRU1436

Replaced all the vacuum hoses, and carb fuel filter. Took it for a test drive and eliminated the rough idle while stopped in drive.

I’m a big fan of fixing vacuum leaks, #1 pet peeve when the carb signal gets altered!

I just looked at mine from my garage chair today.

SRU1436 · 05-24-2020, 02:57 PM

Quote:

Originally Posted by j_cst_10

I’m a big fan of fixing vacuum leaks, #1 pet peeve when the carb signal gets altered!

I just looked at mine from my garage chair today.

I agee.

**rustytruck50** · 05-24-2020, 02:08 PM

Removed the side mount aluminum tool box and fire extinguisher bracket from the bed of my new truck....lookin' better already!
Next up....back rack & warning lights

tim_mc · 05-24-2020, 02:57 PM

Today I FINALLY got my new Edelbrock AVS2 650cfm carb running correctly on my new 350 engine.

**Ol Blue K20** · 05-24-2020, 03:48 PM

I drove mine to the store. The girlfriend wanted Tri Tip for her birthday dinner.....

OregonNed · 05-24-2020, 05:59 PM

Today I started the process of fixing the weep hole leak (when parking uphill) from my transmission. The vent tube up above is clear so I pulled the drive shaft And tail housing. From photos I’ve seen I expected to see some sort of inner seal or o ring but nothing present or much of a groove for one where the splines Start. I’m not even sure if mechanically that would seal the driveshaft yoke.

**SoCoC10** · 05-24-2020, 10:10 PM

Spent the day at the media blaster. Of course no rain in the forecast yet I was dodging drops on the way back to the shop.

External · 05-24-2020, 11:20 PM

After finally massaging in new break lines, installing the new booster, master cylinder and shiny new stuff.

OregonNed · 05-26-2020, 03:43 PM

Got the bearing surfaces cleaned up on my driveshaft and yoke. Installed the tailhousing back on and waiting for new Spicer joints to arrive today. Should have a non leaking yoke now.

**allchevy58** · 05-30-2020, 10:00 PM

Thursday evening and today started sanding. Don't think I'll find any bondo.

Quikshft · 05-31-2020, 12:34 AM

Today I am closing the door on my gear change project. Went from 3.07 to 4.11. Granny first gear used to have some value with my small travel trailer, but I'm afraid it is now rendered useless and starts in second gear will work fine. I will go from about 1700 rpm in fourth to a more reasonable 2400 rpm at 55 mph with my 33 inch tires.

**truckdude239** · 05-31-2020, 04:18 PM

i installed new matching door locks and ignition lock so id have 1 key since i couldn't find my door keys which got lost over the last 8 years if ti being tore apart.. of course i found the door keys last night after the new locks showed up...

**Ol Blue K20** · 05-31-2020, 04:35 PM

Don't feel bad, I have the same kind of luck......basic Murphys Law......

**Grumpy old man** · 06-01-2020, 12:07 PM

Added some CPP disc brake calipers .

67C10Step · 06-01-2020, 12:51 PM

Just stared at mine over the weekend to get an idea of what to tackle next. Wife got me a new set of body mounts for anniversary so that's on the list. Want to knock the front end out but waiting to order and get parts here first.

Did paint my old 5x12 utility trailer though. Not a great job but it is one color now.

66clow · 06-02-2020, 08:02 AM

Finally posed in front of the old Chevy sign.

05-21-2020, 09:30 AM	#3
j_cst_10 Senior Member Join Date: Nov 2008 Location: Cleveland, OH Posts: 585	Re: What did you do to your truck today.The 3rd chapter I didn’t know that. Yeah mine was just blue cloth. The boards are all warped anyway so may try the board/cloth pre assembled headliner. __________________ 1972 Cheyenne Super 20 Custom Camper 12 Valve Cummins/5spd manual 1972 Cheyenne Super Short Bed 557 Med Olive DK olive 1970 K5 Blazer Dark Gold 1966 Coronet 440 35k mile survivor 1991 Suburban 2500 454/4L80E 2wd 1985 Monte Carlo SS 383 Sbc, t-56 magnum 6spd and Ford 9"

05-22-2020, 11:16 AM	#5
SRU1436 Registered User Join Date: Mar 2019 Location: Northern California Posts: 212	Re: What did you do to your truck today.The 3rd chapter I drove mine yesterday, I think it developed a vacuum leak. Have to work on that. Otherwise she is doing well. Attached Images

05-22-2020, 04:32 PM	#6
ohboy321 Senior Member Join Date: Aug 2015 Location: Dunbarton, NH Posts: 277	Re: What did you do to your truck today.The 3rd chapter Cleaned up the 4x4 fan shroud I bought from CUSTOM/10. I used Gunk, de-greaser and a power washer, being careful to not mar the factory finish. Will be nice when installed. Attached Images __________________ Steve/NH 1967 K10 327 Short Bed Stepside 2008 F350 Power Stroke 2007 BMW X3 2020 BMW 540xi 1995 Harley FLSTC

05-22-2020, 09:26 PM	#8
67C10Step Registered User Join Date: Jul 2019 Location: Beebe, AR Posts: 2,441	Re: What did you do to your truck today.The 3rd chapter Finally broke down and removed all the heater and controls. I’ll probably be in the hospital due to the hantavirus with all the mouse stuff in there. The outer box was completely full of leaves, acorns, and dirt dauber nests. Good news was the fan motor worked after knocking a pound of mud nests off the wheel. Bad news is the outer box is pretty much shot. Lower left corner is broken and the metal area between the fan and firewall is rusted gone. __________________ 1967 C10 1980 Jeep CJ5 2020 Toyota 4Runner 2024 Toyota Tundra

05-24-2020, 01:27 PM	#9
SRU1436 Registered User Join Date: Mar 2019 Location: Northern California Posts: 212	Re: What did you do to your truck today.The 3rd chapter Replaced all the vacuum hoses, and carb fuel filter. Took it for a test drive and eliminated the rough idle while stopped in drive.

05-24-2020, 02:08 PM	#12
rustytruck50 Senior Member Join Date: Feb 2011 Location: Papillion, Ne Posts: 897	Re: What did you do to your truck today.The 3rd chapter Removed the side mount aluminum tool box and fire extinguisher bracket from the bed of my new truck....lookin' better already! Next up....back rack & warning lights __________________ -Doug '05 RCSB Sierra 2WD '71 Sierra 2WD Longbed '98 Silverado K1500 Xcab...sold '72 Highlander"Raymond"...sold

05-24-2020, 02:57 PM	#13
tim_mc Registered User Join Date: Jan 2019 Location: St Peters, MO Posts: 436	Re: What did you do to your truck today.The 3rd chapter Today I FINALLY got my new Edelbrock AVS2 650cfm carb running correctly on my new 350 engine. Attached Images __________________ 1967 C20, 350 SBC w/Comp roller cam, 700R4 w/3.42 posi, PS, 4-wheel PDB, Old Air AC & GM Tilt column.

05-24-2020, 03:48 PM	#14
Ol Blue K20 Proprietor of Dale's Corner Join Date: Nov 2012 Location: Vacaville , CA Posts: 15,885	Re: What did you do to your truck today.The 3rd chapter I drove mine to the store. The girlfriend wanted Tri Tip for her birthday dinner..... __________________ "Some Days Chickens And Some Days Feathers" Dale XNGH ECV Sam Brannan 1004 R.I.P. 67ChevyRedneck R.I.P. Grumpy Old Man

05-24-2020, 05:59 PM	#15
OregonNed Registered User Join Date: Dec 2012 Location: Vancouver, Washington Posts: 1,644	Re: What did you do to your truck today.The 3rd chapter Today I started the process of fixing the weep hole leak (when parking uphill) from my transmission. The vent tube up above is clear so I pulled the drive shaft And tail housing. From photos I’ve seen I expected to see some sort of inner seal or o ring but nothing present or much of a groove for one where the splines Start. I’m not even sure if mechanically that would seal the driveshaft yoke. Attached Images __________________ 1968 Chevrolet C/10 LWB - 327, TH350 - 4/5 Drop

05-24-2020, 10:10 PM	#16
SoCoC10 Senior Member Join Date: Nov 2014 Location: Colorado Posts: 3,157	Re: What did you do to your truck today.The 3rd chapter Spent the day at the media blaster. Of course no rain in the forecast yet I was dodging drops on the way back to the shop. Attached Images __________________ 07' Extcab Silverado Z71 Silver Birch, 5.3L HO 71' Cheyenne C10 Hugger Orange on Saddle SWB Besides these two, too Many to count Last edited by SoCoC10; 05-24-2020 at 10:22 PM.

05-24-2020, 11:20 PM	#17
External Registered User Join Date: Jun 2018 Location: Louisiana Posts: 185	Re: What did you do to your truck today.The 3rd chapter After finally massaging in new break lines, installing the new booster, master cylinder and shiny new stuff. Attached Images __________________ '72 Chevy Custom Deluxe Highlander. Med Olive/White 350/200 ps,pb and Air Conditioning!

05-26-2020, 03:43 PM	#18
OregonNed Registered User Join Date: Dec 2012 Location: Vancouver, Washington Posts: 1,644	Re: What did you do to your truck today.The 3rd chapter Got the bearing surfaces cleaned up on my driveshaft and yoke. Installed the tailhousing back on and waiting for new Spicer joints to arrive today. Should have a non leaking yoke now. Attached Images __________________ 1968 Chevrolet C/10 LWB - 327, TH350 - 4/5 Drop

05-30-2020, 10:00 PM	#19
allchevy58 Senior Member Join Date: Aug 2011 Location: Reno, Nv. Posts: 1,424	Re: What did you do to your truck today.The 3rd chapter Thursday evening and today started sanding. Don't think I'll find any bondo. Attached Images __________________ 1927 Willy's Knight 24,000 original miles, 1958 Impala 283/Powerglide, 1964 C-30 383/4 speed, 1971 Monte Carlo 350/350, 1972 GMC K2500 350/350, 1976 Chev. K10 350/350, 2006 GMC Sierra 2500HD LBZ Duramax/Allison, 2006 Chev. Silverado K3500 LBZ Duramax/Allison

05-31-2020, 12:34 AM	#20
Quikshft Registered User Join Date: Oct 2010 Location: Kingsburg, Ca. Posts: 92	Re: What did you do to your truck today.The 3rd chapter Today I am closing the door on my gear change project. Went from 3.07 to 4.11. Granny first gear used to have some value with my small travel trailer, but I'm afraid it is now rendered useless and starts in second gear will work fine. I will go from about 1700 rpm in fourth to a more reasonable 2400 rpm at 55 mph with my 33 inch tires. Attached Images

05-31-2020, 04:18 PM	#21
truckdude239 Senior Member Join Date: Sep 2005 Location: Lewisville, Nc Posts: 10,226	Re: What did you do to your truck today.The 3rd chapter i installed new matching door locks and ignition lock so id have 1 key since i couldn't find my door keys which got lost over the last 8 years if ti being tore apart.. of course i found the door keys last night after the new locks showed up... __________________ David fuller Ase Certified Mechanic Click here to help support our board!! 1971 Chevy c-10 under going a 4.8l LSx swap Build Thread http://67-72chevytrucks.com/vboard/s...d.php?t=421305 2007 Honda Accord my daily 145kmiles 2002 Honda Accord 4 door With 330k(sisters car) 2005 toyota Avalon 228k( brothers car) 2002 Sububran 5.3 245k 2000 Tahoe 5.3l 378 General manager for Marco's Carwash & lube



Register or Log In To remove these advertisements.

05-31-2020, 04:35 PM	#22
Ol Blue K20 Proprietor of Dale's Corner Join Date: Nov 2012 Location: Vacaville , CA Posts: 15,885	Re: What did you do to your truck today.The 3rd chapter Don't feel bad, I have the same kind of luck......basic Murphys Law...... __________________ "Some Days Chickens And Some Days Feathers" Dale XNGH ECV Sam Brannan 1004 R.I.P. 67ChevyRedneck R.I.P. Grumpy Old Man

06-01-2020, 12:07 PM	#23
Grumpy old man Senior Member Join Date: Dec 2013 Location: Gods country East,Tn Posts: 8,545	Re: What did you do to your truck today.The 3rd chapter Added some CPP disc brake calipers . Attached Images __________________ 1967 Factory short bed - Old school '71 - 350 / 4bolt / 487 heads / Edelbrock C3BX Muncie M-22 4 speed / Hurst Comp plus Factory 12 bolt posi 3.73 / 255-70-15 Smoothed firewall / Factory cowl induction Power disc brakes / power steering / 3.5-5" drop

06-01-2020, 12:51 PM	#24
67C10Step Registered User Join Date: Jul 2019 Location: Beebe, AR Posts: 2,441	Re: What did you do to your truck today.The 3rd chapter Just stared at mine over the weekend to get an idea of what to tackle next. Wife got me a new set of body mounts for anniversary so that's on the list. Want to knock the front end out but waiting to order and get parts here first. Did paint my old 5x12 utility trailer though. Not a great job but it is one color now. __________________ 1967 C10 1980 Jeep CJ5 2020 Toyota 4Runner 2024 Toyota Tundra

06-02-2020, 08:02 AM	#25
66clow Registered User Join Date: Jun 2012 Location: Clearwater Beach Florida Posts: 872	Re: What did you do to your truck today.The 3rd chapter Finally posed in front of the old Chevy sign. Attached Images

Register or Log In To remove these advertisements.