2wd swap - Page 3 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

KQQL IT · 06-19-2021, 02:41 PM

Rotor fits in the wheel center. Was really concerned they wouldn't.
But the rotor got swallowed up in a 20" wheel.

SCOTI · 06-19-2021, 11:42 PM

What diameter rotor? 13" (12.8) or ??

KQQL IT · 06-20-2021, 02:01 AM

Quote:

Originally Posted by SCOTI

What diameter rotor? 13" (12.8) or ??

11.9 according to the order.
Powerstop rotors.
Seems like enough room for a pad swap with out taking the wheels off. Ha !

SCOTI · 06-20-2021, 11:14 AM

Ahh.... Replacement C10 size. I though you might have upsized.

KQQL IT · 06-20-2021, 12:54 PM

Quote:

Originally Posted by SCOTI

Ahh.... Replacement C10 size. I though you might have upsized.

Yes. Original plan was 18 inch wheels.
But they backordered til end of August so got the 20's and the rotor looks silly in there

KQQL IT · 07-13-2021, 03:20 AM

Bag plate questions.
Bolt bag to plates then bolt the plate to crossmember?
The fit seems kind of sloppy

SCOTI · 07-13-2021, 09:40 AM

Quote:

Originally Posted by KQQL IT

Bag plate questions.
Bolt bag to plates then bolt the plate to crossmember?
The fit seems kind of sloppy

I noted that on the 1st pair of plates acquired (from AirRide Technologies) so that's been a day or so ago. Since then, I've made my own & build them to better follow the contour/bend. I basically 'score' a line in the plate w/a cut-off disc where I want the bend. Bend or draw the plate to better follow the contour then run a bead down it & clean it up w/a flap disc on the angle grinder.

Some plates I've seen are shorter & don't make it to the area of the curve so it just depends on the plates. Either works.

I get the plates bolted in place on the outside perimeter of the x-member. Then get the lower arm w/bag bolted in place. This allows the bag to be optimally placed in the a-arm pocket/area. Then I use a template that's reference marked from the bag for the orientation of the top mounting hardware hole locations.

KQQL IT · 07-14-2021, 09:39 PM

I'm thinking we're gonna cut the bag plate to fit in the spring bucket hole and weld it in.
Poke 2 holes in the top of the spring bucket for a socket with 2 studs in the air bag.

tinydb84 · 07-19-2021, 12:43 PM

Its hard to tell what it is but is that a piece of tube welded to the top of the c notch?

SCOTI · 07-19-2021, 01:01 PM

Quote:

Originally Posted by tinydb84

Its hard to tell what it is but is that a piece of tube welded to the top of the c notch?

My guess was it's reinforcement because of the c-notch depth into the rail.
I did something similar to my 99 OBS to retain as much of the uncut OE rail strength.

tinydb84 · 07-19-2021, 02:26 PM

Quote:

Originally Posted by SCOTI

My guess was it's reinforcement because of the c-notch depth into the rail.
I did something similar to my 99 OBS to retain as much of the uncut OE rail strength.

Thats what I was thinking.

Just make sure you are able to seal it up well so it doesnt build up a bunch of moisture and rust out.

SCOTI · 07-19-2021, 03:03 PM

Quote:

Originally Posted by tinydb84

Thats what I was thinking.

Just make sure you are able to seal it up well so it doesnt build up a bunch of moisture and rust out.

True.

My logic is if water can get in there, so can air. I stitch welded mine so I'm not worried in my Southern spot on the map but it is something to keep in mind.

KQQL IT · 07-19-2021, 04:42 PM

Quote:

Originally Posted by tinydb84

Its hard to tell what it is but is that a piece of tube welded to the top of the c notch?

Keep things from moving to much with the heat of welding the side plates in and will fit between the bed floor when we're done.
Baby step notch if you will

KQQL IT · 07-20-2021, 12:37 AM

Its stitched in and if it sees any water I'd be surprised. That's what a daily beater is for.

KQQL IT · 07-23-2021, 09:20 PM

Floor is going to get hacked now. Ha
Diff is hard in to it.
Axle tube is still 6 inches from the floor yet.
And a looks like a driveshaft tunnel maybe required

SCOTI · 07-23-2021, 09:59 PM

Sweet jeezus. Looking nice....

KQQL IT · 07-24-2021, 12:36 AM

Quote:

Originally Posted by SCOTI

Sweet jeezus. Looking nice....

Thanks, Jay had a similar reaction.
Now to un bolt the floor and raise it. Or cut the floor and quarters.
I think the tubs alone are high enough but where the quarter bolts to the tub is in the way.

SCOTI · 07-24-2021, 03:20 PM

Quote:

Originally Posted by KQQL IT

Thanks, Jay had a similar reaction.
Now to un bolt the floor and raise it. Or cut the floor and quarters.
I think the tubs alone are high enough but where the quarter bolts to the tub is in the way.

From the couple of burb threads I've watched on here, I believe you are correct (floor & quarters are the initial limitations).

KQQL IT · 07-24-2021, 04:40 PM

Good thing it's not a last year 2wd jimmy or anything.
Time to break in our new plasma Cutter

Snarl95 · 08-03-2021, 04:16 PM

looking good

blazer2007 · 08-04-2021, 10:20 AM

On my 78 I raised the floor 3 inchs and there was one piece of the tunnel I had to cut out just behind the seat. Looks likes a cross brace I replaced the whole floor as was rotten in all 4 corners but made the floor removable just in case. Also with the raised floor I could run full exhaust, was too loud for me even with quiet mufflers. Hope it helps.

KQQL IT · 08-14-2021, 12:00 AM

Keeping a 17 yr old motivated is fun.

Baby step getting finished up

KQQL IT · 09-28-2021, 10:09 PM

This kid is something else.

SCOTI · 09-29-2021, 09:58 AM

I would agree. He's doing well. Especially for being a young-gun.

KQQL IT · 10-01-2021, 10:45 AM

Not suspension related.
But weave aluminum?
Seriously !?

06-19-2021, 02:41 PM	#1
KQQL IT At the body shop. Join Date: Aug 2009 Location: Land of fruits and nuts. Posts: 5,163	Re: 2wd swap Rotor fits in the wheel center. Was really concerned they wouldn't. But the rotor got swallowed up in a 20" wheel. Attached Images __________________ " That didnt make it any newer " " Dont antique the equipment " Last edited by KQQL IT; 06-19-2021 at 09:23 PM.

06-19-2021, 11:42 PM	#2
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 21,924	Re: 2wd swap What diameter rotor? 13" (12.8) or ?? __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.*

06-20-2021, 11:14 AM	#4
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 21,924	Re: 2wd swap Ahh.... Replacement C10 size. I though you might have upsized. __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.*

07-13-2021, 03:20 AM	#6
KQQL IT At the body shop. Join Date: Aug 2009 Location: Land of fruits and nuts. Posts: 5,163	Re: 2wd swap Bag plate questions. Bolt bag to plates then bolt the plate to crossmember? The fit seems kind of sloppy Attached Images __________________ " That didnt make it any newer " " Dont antique the equipment "

07-14-2021, 09:39 PM	#8
KQQL IT At the body shop. Join Date: Aug 2009 Location: Land of fruits and nuts. Posts: 5,163	Re: 2wd swap I'm thinking we're gonna cut the bag plate to fit in the spring bucket hole and weld it in. Poke 2 holes in the top of the spring bucket for a socket with 2 studs in the air bag. __________________ " That didnt make it any newer " " Dont antique the equipment "

07-19-2021, 12:43 PM	#9
tinydb84 Registered User Join Date: Jul 2009 Location: San Jose Ca Posts: 2,871	Re: 2wd swap Its hard to tell what it is but is that a piece of tube welded to the top of the c notch? __________________ David Used parts build: http://67-72chevytrucks.com/vboard/s...d.php?t=638991 My brother's Nova: http://www.67-72chevytrucks.com/vboa...d.php?t=727985 Rear suspension rework: http://www.67-72chevytrucks.com/vboa...d.php?t=750557 Instagram: myfabguy

07-20-2021, 12:37 AM	#14
KQQL IT At the body shop. Join Date: Aug 2009 Location: Land of fruits and nuts. Posts: 5,163	Re: 2wd swap Its stitched in and if it sees any water I'd be surprised. That's what a daily beater is for. __________________ " That didnt make it any newer " " Dont antique the equipment "

07-23-2021, 09:20 PM	#15
KQQL IT At the body shop. Join Date: Aug 2009 Location: Land of fruits and nuts. Posts: 5,163	Re: 2wd swap Floor is going to get hacked now. Ha Diff is hard in to it. Axle tube is still 6 inches from the floor yet. And a looks like a driveshaft tunnel maybe required Attached Images __________________ " That didnt make it any newer " " Dont antique the equipment "

07-23-2021, 09:59 PM	#16
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 21,924	Re: 2wd swap Sweet jeezus. Looking nice.... __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.*

07-24-2021, 04:40 PM	#19
KQQL IT At the body shop. Join Date: Aug 2009 Location: Land of fruits and nuts. Posts: 5,163	Re: 2wd swap Good thing it's not a last year 2wd jimmy or anything. Time to break in our new plasma Cutter __________________ " That didnt make it any newer " " Dont antique the equipment "

08-03-2021, 04:16 PM	#20
Snarl95 Registered User Join Date: Jan 2019 Location: edenton nc Posts: 76	Re: 2wd swap looking good __________________ 1995 k3500 cclb srw 6.5 turbo diesel. The lessons that hurt are the lessons that teach. There is always a price to pay. You are free to make any decision you want. You are not free from the consequences.

08-04-2021, 10:20 AM	#21
blazer2007 Registered User Join Date: Jan 2007 Location: vernon b.c. Posts: 3,022	Re: 2wd swap On my 78 I raised the floor 3 inchs and there was one piece of the tunnel I had to cut out just behind the seat. Looks likes a cross brace I replaced the whole floor as was rotten in all 4 corners but made the floor removable just in case. Also with the raised floor I could run full exhaust, was too loud for me even with quiet mufflers. Hope it helps. Attached Images

08-14-2021, 12:00 AM	#22
KQQL IT At the body shop. Join Date: Aug 2009 Location: Land of fruits and nuts. Posts: 5,163	Re: 2wd swap Keeping a 17 yr old motivated is fun. Baby step getting finished up Attached Images __________________ " That didnt make it any newer " " Dont antique the equipment "

09-28-2021, 10:09 PM	#23
KQQL IT At the body shop. Join Date: Aug 2009 Location: Land of fruits and nuts. Posts: 5,163	Re: 2wd swap This kid is something else. Attached Images __________________ " That didnt make it any newer " " Dont antique the equipment "

09-29-2021, 09:58 AM	#24
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 21,924	Re: 2wd swap I would agree. He's doing well. Especially for being a young-gun. __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.*



Register or Log In To remove these advertisements.

10-01-2021, 10:45 AM	#25
KQQL IT At the body shop. Join Date: Aug 2009 Location: Land of fruits and nuts. Posts: 5,163	Re: 2wd swap Not suspension related. But weave aluminum? Seriously !? Attached Images __________________ " That didnt make it any newer " " Dont antique the equipment "

Register or Log In To remove these advertisements.