|
|
|
11-10-2011, 01:03 AM
|
#1 |
|
Registered User
Join Date: Sep 2011
Location: Golden Valley,MN
Posts: 639
|
Re: What Did You Do With Your Truck Today ?
I got the final primer coat on the left rear fender. Tomorrow I am bringing the right door in to work, to tear it down (regulator, latch and handle) then start on the rust clean up and fixing a few dents.
Also tested the "BMW" xenon headlamp conversion. It is going to work great!! |
|
|
11-10-2011, 08:40 AM
|
#2 |
|
Registered User
Join Date: Aug 2011
Location: Kingsport, TN
Posts: 36
|
Re: What Did You Do With Your Truck Today ?
Got the bedliner applied to the cab floor, both inside and out. Will need one more quart to finish, two quarts total. Happy with how it looks, hope who ever buys it will
__________________
We lust for what we want, weep for what we need... |
|
|
|
11-10-2011, 10:52 AM
|
#3 | |
|
Senior Member
  
Join Date: Nov 2008
Location: Glendora, CA
Posts: 6,336
|
Re: What Did You Do With Your Truck Today ?
Quote:
What kind of bedliner, the spray undercoater or the roll on kind? |
|
|
|
|
11-10-2011, 11:02 AM
|
#4 |
|
Registered User
Join Date: Aug 2011
Location: Kingsport, TN
Posts: 36
|
Re: What Did You Do With Your Truck Today ?
I used the Herculiner in the quart size since I'm only doing the cab. Turned out pretty good. like to add another coat if it allows (didn't read that far) and use a roller this time. I think that would look better, but then it will be covered in carpet. Used it for leak prevention on the new panels over the seam sealer, and I'm sure it will quiet things down some. Post up some pics tonight.
I know you have to stir the crap out of it or all the rubber stays in the bottom, DO NOT SHAKE! Why? I don't know; but it says not to.  Oh and on another note; stay away from the Rustoleum spray, might be good if you can get it out of the CAN! Waste of money at almost $8.00 a can.
__________________
We lust for what we want, weep for what we need... |
|
|
|
11-10-2011, 08:54 PM
|
#5 | |
|
Registered User
Join Date: Aug 2011
Location: Kingsport, TN
Posts: 36
|
Re: What Did You Do With Your Truck Today ?
Quote:
__________________
We lust for what we want, weep for what we need... |
|
|
|
|
11-10-2011, 06:30 PM
|
#6 |
|
Registered User
Join Date: Oct 2011
Location: winchester,ky
Posts: 12
|
Re: What Did You Do With Your Truck Today ?
Today i added Tail light mounts and taillights to my flat bed truck. I mounted the mounts to the frame.
|
|
|
|
11-11-2011, 04:44 PM
|
#7 | |
|
Registered User
Join Date: Jul 2011
Location: Auburn ca.
Posts: 2,886
|
Re: What Did You Do With Your Truck Today ?
Quote:
|
|
|
|
|
11-10-2011, 11:27 PM
|
#8 |
|
Senior Member
Join Date: Nov 2008
Location: Glendora, CA
Posts: 6,336
|
Re: What Did You Do With Your Truck Today ?
Okay, okay, I believe you! And it looks nice and solid too. What kind of condition was that floor and those kick panels before you painted it on? I plan to use something like this too after seeing another member's and now yours. BUt I still plan on putting Peel 'n Seal on top of it too!
|
|
|
|
11-10-2011, 11:29 PM
|
#9 |
|
Registered User
Join Date: Jul 2011
Location: Las Vegas - Nev. aka Sin City
Posts: 1,835
|
Re: What Did You Do With Your Truck Today ?
readytogo69
nice truck ! |
|
|
|
11-11-2011, 08:21 AM
|
#10 |
|
Registered User
Join Date: Aug 2011
Location: Kingsport, TN
Posts: 36
|
Re: What Did You Do With Your Truck Today ?
Dan,
the floors had been patched from the under side, leaving the old rusty metal on top and the kick panels were toast. I made all new panels with 18ga sheet metal and cut out the old leaving a boarder to attach to. Couldn't afford new panels at about $100.00 each side shipped, not including the kick panels. I bought the 4'x8'sheet of 18 ga for $48.00 and still have about a 1/2 left of the sheet left. The floor panels are 2 pieces each side. Formed with some angle iron, vicegrips, vice and a hammer! glued in place with body panel adhesive and a few rivets for extra measure. I double sealed it with a water/freeze resistat calk and then the bedliner. Hope I get no leaks! I secon qt. will finish the bottom and hopefully leave enough for a second coat on top, rolled on for a better finish look. Not that it really matters as it will have carpet over it.
__________________
We lust for what we want, weep for what we need... |
|
|
|
11-11-2011, 07:44 PM
|
#11 |
|
Registered User
Join Date: Jul 2011
Location: Las Vegas - Nev. aka Sin City
Posts: 1,835
|
Re: What Did You Do With Your Truck Today ?
police here hate blue dots !
|
|
|
|
11-12-2011, 09:53 PM
|
#12 |
|
Registered User
Join Date: May 2010
Location: Lawrenceville, Ga
Posts: 2,640
|
Re: What Did You Do With Your Truck Today ?
I installed a pair of courtesy lights that come on when the door is opened, and finished up my hazard flashers. I used after market tag lights for the lights, and door switches that I picked out of the NAPA catalog. The hazard switch is mounted where the choke would normally be. It's a Ford switch that I got off of EBay, but I have a chrome Chevy style knob ordered to make it look better..
|
|
|
|
11-13-2011, 10:18 PM
|
#13 |
|
Registered User
Join Date: Aug 2011
Location: Kingsport, TN
Posts: 36
|
Re: What Did You Do With Your Truck Today ?
Did some minor fiberglassing of holes in the inner rocker panels, for lack of knowing what to call them. Hope to smooth them out tomorrow with a little bondo. Got a couple of interested buyers who want to come see it this week. Try and do some little things to make it look better and if they don't take it, I got a little bit more off of the to do list.
And patched a whole in the lower cowl side where it rolls under. Good therapy if nothing else
__________________
We lust for what we want, weep for what we need... |
|
|
|
11-13-2011, 10:56 PM
|
#14 |
|
Registered User
Join Date: Jun 2006
Location: Idaho
Posts: 8,800
|
Re: What Did You Do With Your Truck Today ?
Cleaned up a bunch of small parts for paint. Measured for the gas tank fill pipe.
Posted via Mobile Device
__________________
1959 Chevy Short Fleetside w/ 74 4WD drive train (current project) OrrieG Build Thread 1964 Chevelle Malibu w/ 355-350TH (daily driver) Helpful AD and TF Manual Site Old Car Manual Project |
|
|
|
11-13-2011, 11:39 PM
|
#15 |
|
Registered User
 
Join Date: Jul 2006
Location: Ozark, MO
Posts: 4,887
|
Re: What Did You Do With Your Truck Today ?
Stared longingly at it, then finished bringing in the groceries.
__________________
'20 Silverado Trail Boss ~ '17 Tahoe ~ '79 K15 Sierra Grande ~ '76 Blazer 2wd ~ '71 Cheyenne swb ~ '55 Pontiac Safari ~'50 3100 bagged ~ '80 Wife ~ Late model kids
|
|
|
|
11-15-2011, 09:05 PM
|
#16 | |
|
Registered User
Join Date: Jul 2011
Location: Auburn ca.
Posts: 2,886
|
Re: What Did You Do With Your Truck Today ?
Quote:
Last edited by mknittle; 11-15-2011 at 09:12 PM. |
|
|
|
|
11-14-2011, 01:48 PM
|
#17 |
|
Registered User
Join Date: Apr 2011
Location: San Diego CA
Posts: 241
|
Re: What Did You Do With Your Truck Today ?
Just got off the phone with "fenders n' more" out of Santa Fe Springs CA.
http://fendersnmore.com/ Orered the custom fenders for the flatbed 59. I tried finding ready made fenders but no one had what I needed so I went custom made. If anyone needs a AMERICAN MADE FENDER I recomend these guys. Great customer service, great turn around time and not too bad price wise. Mine will come in at around $100.00 shipped! I should see them around the end of the week or early next week. |
|
|
|
11-14-2011, 02:50 PM
|
#18 |
|
Registered User
Join Date: Oct 2010
Location: Placerville CA
Posts: 186
|
Re: What Did You Do With Your Truck Today ?
In memory of all Vetrans........Got the cab set on chassis over the weekend to check motor/tranny location. Will probably lift the tail of the tranny up about an inch, other wise it sits pretty good. It has been a little over a year since I started ripping it apart. Some progress but long way to go. Hoping to start on motor this winter.
|
|
|
|
11-14-2011, 03:05 PM
|
#19 |
|
Registered User
Join Date: Oct 2011
Location: Roanoke, VA
Posts: 104
|
Re: What Did You Do With Your Truck Today ?
Picked up some wheels from FFredo, installed my front turn signals, wire-loomed under the hood, cleaned up the garage a little in preparation for the under bed gas tank installation coming up.
Nice meeting you FFredo, super nice guy and you were very welcoming. It's great to meet forum members and build friendships. |
|
|
|
11-14-2011, 05:23 PM
|
#20 |
|
Registered User
Join Date: Apr 2011
Location: San Diego CA
Posts: 241
|
Re: What Did You Do With Your Truck Today ?
Good to meet you too Bshort. Hope the rain didn't ruin your San Diego trip too much.
|
|
|
|
11-15-2011, 07:17 PM
|
#21 |
|
Registered User
Join Date: Mar 2011
Location: madison, NC
Posts: 81
|
Re: What Did You Do With Your Truck Today ?
OK hear my pictures.It took us two hours to load it on the trailer, but only thirty minutes to unload.
|
|
|
|
11-15-2011, 11:56 PM
|
#22 |
|
Registered User
Join Date: Nov 2011
Location: Alabama
Posts: 68
|
Re: What Did You Do With Your Truck Today ?
I checked to see if my two front cab mounts were level...
|
|
|
|
11-15-2011, 07:18 PM
|
#23 |
|
Registered User
Join Date: Oct 2011
Location: Roanoke, VA
Posts: 104
|
Re: What Did You Do With Your Truck Today ?
Nope, we brought umbrellas. Spent a couple hours in Seaport Village then headed home.
|
|
|
|
11-16-2011, 03:47 AM
|
#24 |
|
Registered User
Join Date: Jul 2011
Location: Las Vegas - Nev. aka Sin City
Posts: 1,835
|
Re: What Did You Do With Your Truck Today ?
they dont mess with the old cars much here. the local PD has a 1950 some ford police car that shows up now and then at cruze nite
__________________ i wish the police force here would use older cars or trucks - maybe we would have a chance _lol |
|
|
|
11-16-2011, 03:48 AM
|
#25 |
|
Registered User
Join Date: Jul 2011
Location: Las Vegas - Nev. aka Sin City
Posts: 1,835
|
Re: What Did You Do With Your Truck Today ?
AD 51
nice lookin weld work on subframe |
|
|
 |
| Bookmarks |
|
|
Hybrid Mode
