'67 5.3L Build Thread - Page 11 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

snow man · 01-31-2011, 05:43 PM

no build tread but when i get the fittings i will get your e-mail address and send you pictures.

5150.4.67 · 02-01-2011, 12:11 AM

Wow, very clean engine compartment. Looks like it belongs there!

mcbassin · 02-01-2011, 01:56 AM

Quote:

Originally Posted by 5150.4.67

Wow, very clean engine compartment. Looks like it belongs there!

Man that looks amazing! This is a swet setup....just looks like $$$$$ mucho bucks

67C10BUB · 02-01-2011, 06:44 AM

Quote:

Originally Posted by snow man

no build tread but when i get the fittings i will get your e-mail address and send you pictures.

Sounds good, thanks. I'll be sure to post pics of my setup as well (whenever I get around to doing the AC system).

67C10BUB · 02-01-2011, 06:58 AM

Quote:

Originally Posted by mcbassin

Man that looks amazing! This is a swet setup....just looks like $$$$$ mucho bucks

Thanks guys. I guess "mucho $$$" is different to everyone, but for a daily driver I am still WAY under a newer truck (that I would like as much).

68Driver · 02-02-2011, 04:34 PM

Hello All, I have my frame cut down and dusted all the snow off of it and brought it back in the garage to start grinding some rivets off. What is everyone's experience with painting or powder coating the frame?? What do you think 67c10bub??

**Clyde65** · 02-02-2011, 04:51 PM

are you going to drive this everyday? or just for parties?

68Driver · 02-02-2011, 04:52 PM

It won't be a daily driver but a driver.

smokinstang70 · 02-02-2011, 05:10 PM

I used a Sherwin Williams Exterior Industrial epoxy paint on my build... very happy with the results... however I have not started driving mine to see how it holds up to daily use. Powdercoat is usually a more durable finish... my only problem was I figured i would have to make slight modifications and there is NO way to patch or fix powdercoat.

With all that said.. I will probably try powdercoat on my next project.

smokinstang70 · 02-02-2011, 05:12 PM

67C10BUB... did you use the supplied header gaskets with your DT headers? I was told to buy new, better quality gaskets and not use the ones supplied. Just wanted your opinion. Also did you use the supplied hardware or something like ARP header bolts?

Thanks as always

67C10BUB · 02-02-2011, 06:35 PM

Quote:

Originally Posted by 68Driver

Hello All, I have my frame cut down and dusted all the snow off of it and brought it back in the garage to start grinding some rivets off. What is everyone's experience with painting or powder coating the frame?? What do you think 67c10bub??

I just wire wheeled, sanded, primed, and painted semi-gloss black with Rustoleum. I would have liked to powder coat, but it just wasn't in the budget. I am going for a more factory look than a show car look anyway.

67C10BUB · 02-02-2011, 06:38 PM

Quote:

Originally Posted by smokinstang70

67C10BUB... did you use the supplied header gaskets with your DT headers? I was told to buy new, better quality gaskets and not use the ones supplied. Just wanted your opinion. Also did you use the supplied hardware or something like ARP header bolts?

Thanks as always

Yes, I used the DT gaskets and I don't have any leaks. I always spray both sides of my header gaskets with Permatex Copper Spray-A-Gasket. You can buy it at any Auto Zone, etc. I also used the hardware that came with the headers.

67chevy1series · 02-02-2011, 06:52 PM

so is your truck a real panoramic 67?

67C10BUB · 02-03-2011, 06:42 AM

Quote:

Originally Posted by 67chevy1series

so is your truck a real panoramic 67?

The cab is a 67 c20 and the chassis is from a 71 c10.

67chevy1series · 02-03-2011, 10:32 PM

sweet its nice to know it is actually a 67, got a rare cab !

mcbassin · 02-04-2011, 12:25 AM

I used to love driving my 67 (small window) around with all the thumbs up you get, but the blind spots are huge. I wish I still had it.

67chevy1series · 02-04-2011, 12:34 AM

yes i love the small windows! but in a 60 66 i would have to have a big window! i guess im a wierd character right!

67C10BUB · 02-12-2011, 12:34 AM

I got the exhaust done today by Ralph's Muffler in Fontana CA. I can't say enough good things about Gabe, the technician that did the install. I got 2 Magnaflow mufflers, 2 rolled lip tips, and full custom install with an H-pipe for $450 out the door. This seems like a killer deal to me and the welds/bends look absolutely perfect. He even installed 4 hangers with rubber isolators. If anyone is in the IE in CA I would strongly suggest looking into Ralph's. These pics are during the install before the H-pipe was installed. I'll try and get more of the completed system.

67C10BUB · 02-12-2011, 12:35 AM

I came across this pic of my truck and just wanted to post it.

*Puropedo* · 02-12-2011, 12:42 AM

Damn! Looking good!... May I ask what kind of plug wires you ended up using for the DT headers?

67chevy1series · 02-12-2011, 02:03 AM

johnny is right it is lookin good!!!!!

67C10BUB · 02-12-2011, 12:38 PM

Quote:

Originally Posted by Puropedo

Damn! Looking good!... May I ask what kind of plug wires you ended up using for the DT headers?

I used the MSD 32819 and they worked out great. The ends are bendable, so they can be moved around the header tubes as needed.

67C10BUB · 02-18-2011, 03:10 PM

Here are a few of the completed exhaust.

68GMCCustom · 02-18-2011, 05:06 PM

Looks nice!

smokinstang70 · 03-06-2011, 11:44 PM

Truck is looking great man... hope mine turns out looking this good.

Question... can you post a picture of your oil dip stick install? you used a ED5008 (Lokar) stick right?

Thanks man

01-31-2011, 05:43 PM	#251
snow man Registered User Join Date: Mar 2002 Location: mt. zion illinois Posts: 276	Re: '67 5.3L Build Thread no build tread but when i get the fittings i will get your e-mail address and send you pictures.

02-01-2011, 12:11 AM	#252
5150.4.67 Registered User Join Date: Dec 2007 Location: Modesto, Ca Posts: 411	Re: '67 5.3L Build Thread Wow, very clean engine compartment. Looks like it belongs there!

02-02-2011, 04:34 PM	#256
68Driver Registered User Join Date: Nov 2010 Location: Minnesota Posts: 47	Re: '67 5.3L Build Thread Hello All, I have my frame cut down and dusted all the snow off of it and brought it back in the garage to start grinding some rivets off. What is everyone's experience with painting or powder coating the frame?? What do you think 67c10bub??

02-02-2011, 04:51 PM	#257
Clyde65 1965 Chevy C10, 2005 4.8L/4l60 Join Date: Aug 2004 Location: DFW Texas Posts: 8,540	Re: '67 5.3L Build Thread are you going to drive this everyday? or just for parties? __________________ Clyde65 Rebuild of Clyde http://67-72chevytrucks.com/vboard/s...84#post8338184 69 Aristocrat Lo Liner build http://67-72chevytrucks.com/vboard/s...84#post7561684 *support our troops!*

02-02-2011, 04:52 PM	#258
68Driver Registered User Join Date: Nov 2010 Location: Minnesota Posts: 47	Re: '67 5.3L Build Thread It won't be a daily driver but a driver.

02-02-2011, 05:10 PM	#259
smokinstang70 Registered User Join Date: Feb 2009 Location: Savannah GA Posts: 505	Re: '67 5.3L Build Thread I used a Sherwin Williams Exterior Industrial epoxy paint on my build... very happy with the results... however I have not started driving mine to see how it holds up to daily use. Powdercoat is usually a more durable finish... my only problem was I figured i would have to make slight modifications and there is NO way to patch or fix powdercoat. With all that said.. I will probably try powdercoat on my next project. __________________ "Love Affair" Build Thread

02-02-2011, 05:12 PM	#260
smokinstang70 Registered User Join Date: Feb 2009 Location: Savannah GA Posts: 505	Re: '67 5.3L Build Thread 67C10BUB... did you use the supplied header gaskets with your DT headers? I was told to buy new, better quality gaskets and not use the ones supplied. Just wanted your opinion. Also did you use the supplied hardware or something like ARP header bolts? Thanks as always __________________ "Love Affair" Build Thread

02-02-2011, 06:52 PM	#263
67chevy1series Registered User Join Date: Mar 2010 Location: a t w a t e r cali 95301 Posts: 10,713	Re: '67 5.3L Build Thread so is your truck a real panoramic 67?

02-03-2011, 10:32 PM	#265
67chevy1series Registered User Join Date: Mar 2010 Location: a t w a t e r cali 95301 Posts: 10,713	Re: '67 5.3L Build Thread sweet its nice to know it is actually a 67, got a rare cab !

02-04-2011, 12:25 AM	#266
mcbassin Still Learning Join Date: Jul 2009 Location: Central Oklahoma Posts: 10,108	Re: '67 5.3L Build Thread I used to love driving my 67 (small window) around with all the thumbs up you get, but the blind spots are huge. I wish I still had it. __________________ Mike "69 Short Wide" My Project 86 Silverado Landen's Project Instagram: @mcbassin My Website C/10 Club Oklahoma Facebook Group

02-04-2011, 12:34 AM	#267
67chevy1series Registered User Join Date: Mar 2010 Location: a t w a t e r cali 95301 Posts: 10,713	Re: '67 5.3L Build Thread yes i love the small windows! but in a 60 66 i would have to have a big window! i guess im a wierd character right!

02-12-2011, 12:34 AM	#268
67C10BUB Registered User Join Date: Aug 2010 Location: Alta Loma, CA Posts: 610	Re: '67 5.3L Build Thread I got the exhaust done today by Ralph's Muffler in Fontana CA. I can't say enough good things about Gabe, the technician that did the install. I got 2 Magnaflow mufflers, 2 rolled lip tips, and full custom install with an H-pipe for $450 out the door. This seems like a killer deal to me and the welds/bends look absolutely perfect. He even installed 4 hangers with rubber isolators. If anyone is in the IE in CA I would strongly suggest looking into Ralph's. These pics are during the install before the H-pipe was installed. I'll try and get more of the completed system. Attached Images __________________ 67 5.3L Build

02-12-2011, 12:35 AM	#269
67C10BUB Registered User Join Date: Aug 2010 Location: Alta Loma, CA Posts: 610	Re: '67 5.3L Build Thread I came across this pic of my truck and just wanted to post it. Attached Images __________________ 67 5.3L Build

02-12-2011, 12:42 AM	#270
Puropedo Account Suspended Join Date: Nov 2008 Location: Prunedale California Posts: 782	Re: '67 5.3L Build Thread Damn! Looking good!... May I ask what kind of plug wires you ended up using for the DT headers?

02-12-2011, 02:03 AM	#271
67chevy1series Registered User Join Date: Mar 2010 Location: a t w a t e r cali 95301 Posts: 10,713	Re: '67 5.3L Build Thread johnny is right it is lookin good!!!!!



Register or Log In To remove these advertisements.

02-18-2011, 03:10 PM	#273
67C10BUB Registered User Join Date: Aug 2010 Location: Alta Loma, CA Posts: 610	Re: '67 5.3L Build Thread Here are a few of the completed exhaust. Attached Images __________________ 67 5.3L Build

02-18-2011, 05:06 PM	#274
68GMCCustom Truck and auto performance nut Join Date: Feb 2007 Location: McKinney,Texas Posts: 3,848	Re: '67 5.3L Build Thread Looks nice! __________________ Kurt - '68 GMC short step - NIB '09 LY6 6.0L crate motor w/mods, NIB '12 crate 4L85e w/billet 3k stall Circle D, 3.73 posi 12 bolt, DynaTech f-swap headers, 3/4 drop, handling mods, etc. - my toy '72 Chevy LWB C-10 Highlander - 350/350 ps/pb/tilt/ac - not original but close '06 Chevy TrailBlazerSS - LS2/4L70e - little black hot rod SUV - my DD '18 Kia Sorento - wife's econo-driver '95 Chevy S10 - reg cab shortbed, LS, 4.3, auto... my '68's powertrain and chassis build -links broken A surprise phase - carb to efi -links broken

03-06-2011, 11:44 PM	#275
smokinstang70 Registered User Join Date: Feb 2009 Location: Savannah GA Posts: 505	Re: '67 5.3L Build Thread Truck is looking great man... hope mine turns out looking this good. Question... can you post a picture of your oil dip stick install? you used a ED5008 (Lokar) stick right? Thanks man __________________ "Love Affair" Build Thread

Register or Log In To remove these advertisements.