What did you do to your truck today? - Page 289 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

RANDY COX · 03-17-2013, 12:59 PM

Quote:

Originally Posted by bigdan3131

i did exactly nothing except watch the rain fall...the trucks outside with no garage or canopy to work under. Maybe it will stop raining by july...

i know what your sayin i don't have a garage either.

Quote:

Originally Posted by gmcdeadhead

i ground off the leaf perches and the shock mounts on the 14 bolt conversion i'm going to do on the 66 c-20. Also getting ready to ship the 65 gmc out for body work and primer,[img]

[img]

[/img][/img]

it's funny everybody is going 14 boltff 3/4 stuff i changed from 3/4 to 1/2 ton had the 3/4 had better gears like 373's i would have left it alone....

gmcdeadhead · 03-17-2013, 01:18 PM

i'm doing the 14 bolt conversion on the rear , the front disc brake conversion on the front, the power steering and putting hydro boost on it as well, i got it all off a 1987 1 ton truck that i bought for $600. there was a new p/s gear box put on , new tie rods , idler arm , pittman arm , centerlink , new booster hoses, a new p/s pump, new brakes up front and calipers , i scored big time getting that chassis. and i'll scrap the frame and get some money back. NICE.

bonehead · 03-17-2013, 01:34 PM

I installed my sway bar today. I used the dropped mounts since the front of my truck is low. I ran into no issues on the installation. Everything went smooth just like discussed on the board. My bar is the 1 1/16' off of a 1984 c-10.

towersddg9 · 03-17-2013, 03:26 PM

putting the bed and cowls on, all that's left is glass, carpet trim and bedwood
Thanks for all the input

akaupp · 03-17-2013, 03:54 PM

I don't get to work on my truck today as we have friends coming over, but I get to show it off and talk about it a little. I opened the door and remembered I got the 64 Utah plates for it. I figure since they're green and it's St. Patrick's Day, I'll post a picture.

Everyone be safe and smart out there today.

ChuckW · 03-17-2013, 05:41 PM

Quote:

Originally Posted by Vernski

I bought them 3-4 years ago and I think it was Brothers Trucks, I ordered the bumper at the same time. I have seen them other places so they are out there, you could Google for them I think they are called splash pans, good luck...Vernski

Thanks! And Nice job on your Truck btw!!

racecougar · 03-17-2013, 07:34 PM

Installed the passenger side rocker panel today.

hemifalcon · 03-17-2013, 08:24 PM

Quote:

Originally Posted by racecougar

Installed the passenger side rocker panel today.

Nice job man..
Posted via Mobile Device

RANDY COX · 03-17-2013, 08:32 PM

Quote:

Originally Posted by hemifalcon

Nice job man..
Posted via Mobile Device

I second that nice job wished mine was already done,I'm ordering my stuff today...

racecougar · 03-17-2013, 09:01 PM

Thanks guys. It's coming along.

towersddg9 · 03-17-2013, 09:22 PM

bed on, still gotta get it lined up

Minzer · 03-17-2013, 09:36 PM

Quote:

Originally Posted by towersddg9

bed on, still gotta get it lined up

Very nice work! congratulations

CRGRS 66 · 03-17-2013, 09:52 PM

Quote:

Originally Posted by towersddg9

bed on, still gotta get it lined up

looks effn amazing, congratulations

I did some cleaning up... and I found my work bench!

RANDY COX · 03-17-2013, 09:55 PM

Ordered my rockers and patch panels,,OOOOH YA BABY....

markeb01 · 03-17-2013, 10:05 PM

Spent the afternoon replacing the stainless hex bolts in my rear splash pans with black carriage bolts.

60n60Apache · 03-17-2013, 10:53 PM

60 C10 Apache.

Today got those 2.5" Magnaflow, w/hugger headers completed.

mud.man.rj · 03-17-2013, 10:58 PM

Exh looks good, man the diff always reminds me of a 9" Ford. How does it sound is what I want to know hmm.

60n60Apache · 03-18-2013, 12:12 AM

Will do a Youtube post tomorrow.
I love the sound of those Magnaflows.

azdude1964 · 03-18-2013, 12:41 AM

Got thr wipers hooked up and adjusted the hood.Going to dmv tomorrow to get the plates,,,

MrBeast · 03-18-2013, 12:49 AM

Built a receiver mount for my winch and a bracket to put it on my trailer.

Gonna go get my 72 from where I have it stored next month, needed this to get it on the trailer.

markeb01 · 03-18-2013, 01:30 AM

Quote:

Originally Posted by 60n60Apache

60 C10 Apache.

Today got those 2.5" Magnaflow, w/hugger headers completed.

Beautiful workmanship. That's a very nice looking system.

weaintscared · 03-18-2013, 10:55 AM

Started making it a new home,,, Adding on the my shop
My build http://67-72chevytrucks.com/vboard/s...d.php?t=468622

Minzer · 03-20-2013, 11:36 AM

Wash engine!

Trsmotrhed · 03-20-2013, 06:48 PM

Actually this weekend, made my track arm bracket and mounted to frame. Installed rear sway bar.

Posted via Mobile Device

keeks69 · 03-22-2013, 01:39 PM

Finished this today
looks pretty good just waiting for the new clear glass part!

03-17-2013, 01:18 PM	#7202
gmcdeadhead Registered User Join Date: Jul 2007 Location: branchburg, new jersey Posts: 568	Re: What did you do to your truck today? i'm doing the 14 bolt conversion on the rear , the front disc brake conversion on the front, the power steering and putting hydro boost on it as well, i got it all off a 1987 1 ton truck that i bought for $600. there was a new p/s gear box put on , new tie rods , idler arm , pittman arm , centerlink , new booster hoses, a new p/s pump, new brakes up front and calipers , i scored big time getting that chassis. and i'll scrap the frame and get some money back. NICE.

03-17-2013, 01:34 PM	#7203
bonehead Registered User Join Date: Jun 2007 Location: Charlotte, NC Posts: 516	Re: What did you do to your truck today? I installed my sway bar today. I used the dropped mounts since the front of my truck is low. I ran into no issues on the installation. Everything went smooth just like discussed on the board. My bar is the 1 1/16' off of a 1984 c-10. Attached Images __________________ past trucks: 1980 C-10 Silverado SWB 1961 C-10 custom cab LWB 1966 C-10 custom cab LWB

03-17-2013, 03:26 PM	#7204
towersddg9 Registered User Join Date: Dec 2010 Location: Texas Posts: 246	Re: What did you do to your truck today? putting the bed and cowls on, all that's left is glass, carpet trim and bedwood Thanks for all the input Attached Images

03-17-2013, 03:54 PM	#7205
akaupp Registered User Join Date: Jan 2013 Location: West Point, UT Posts: 235	Re: What did you do to your truck today? I don't get to work on my truck today as we have friends coming over, but I get to show it off and talk about it a little. I opened the door and remembered I got the 64 Utah plates for it. I figure since they're green and it's St. Patrick's Day, I'll post a picture. Everyone be safe and smart out there today.

03-17-2013, 07:34 PM	#7207
racecougar Registered User Join Date: Jan 2013 Location: Imperial, MO Posts: 999	Re: What did you do to your truck today? Installed the passenger side rocker panel today. __________________ Rod @ AzzKicker Cars 1965 C10 SWB - Build Thread

03-17-2013, 09:01 PM	#7210
racecougar Registered User Join Date: Jan 2013 Location: Imperial, MO Posts: 999	Re: What did you do to your truck today? Thanks guys. It's coming along. __________________ Rod @ AzzKicker Cars 1965 C10 SWB - Build Thread

03-17-2013, 09:22 PM	#7211
towersddg9 Registered User Join Date: Dec 2010 Location: Texas Posts: 246	Re: What did you do to your truck today? bed on, still gotta get it lined up Attached Images

03-17-2013, 09:55 PM	#7214
RANDY COX Registered User Join Date: Mar 2001 Location: RADFORD, VA Posts: 2,651	Re: What did you do to your truck today? Ordered my rockers and patch panels,,OOOOH YA BABY.... __________________ 1964 BBC 402 4x4

03-17-2013, 10:05 PM	#7215
markeb01 Senior Enthusiast Join Date: Feb 2007 Location: Spokane Valley, WA Posts: 8,356	Re: What did you do to your truck today? Spent the afternoon replacing the stainless hex bolts in my rear splash pans with black carriage bolts. __________________ My Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=444502

03-17-2013, 10:53 PM	#7216
60n60Apache Registered User Join Date: Dec 2010 Location: Atlanta, Georgia Posts: 90	Re: What did you do to your truck today? 60 C10 Apache. Today got those 2.5" Magnaflow, w/hugger headers completed. Attached Images

03-17-2013, 10:58 PM	#7217
mud.man.rj Registered User Join Date: Dec 2011 Location: Creighton Sask. Canada Posts: 4,121	Re: What did you do to your truck today? Exh looks good, man the diff always reminds me of a 9" Ford. How does it sound is what I want to know hmm.

03-18-2013, 12:12 AM	#7218
60n60Apache Registered User Join Date: Dec 2010 Location: Atlanta, Georgia Posts: 90	Re: What did you do to your truck today? Will do a Youtube post tomorrow. I love the sound of those Magnaflows.

03-18-2013, 12:41 AM	#7219
azdude1964 Registered User Join Date: Feb 2013 Location: tucson,az Posts: 179	Re: What did you do to your truck today? Got thr wipers hooked up and adjusted the hood.Going to dmv tomorrow to get the plates,,, Attached Images __________________ efi 496bbc th350 custom brakes narrowed 9 coilover rear.

03-18-2013, 12:49 AM	#7220
MrBeast high-Tech Red Neck Join Date: Feb 2008 Location: Livingston, MT/On my boat WA/BC/AK Posts: 2,294	Re: What did you do to your truck today? Built a receiver mount for my winch and a bracket to put it on my trailer. Gonna go get my 72 from where I have it stored next month, needed this to get it on the trailer. __________________ "He used to be a pretty nice feller, now he's a welder!"

03-18-2013, 10:55 AM	#7222
weaintscared Registered User Join Date: Mar 2011 Location: Sumter SC Posts: 439	Re: What did you do to your truck today? Started making it a new home,,, Adding on the my shop My build http://67-72chevytrucks.com/vboard/s...d.php?t=468622 Attached Images



Register or Log In To remove these advertisements.

03-20-2013, 11:36 AM	#7223
Minzer Registered User Join Date: Mar 2013 Location: buenos aires - argentina Posts: 36	Re: What did you do to your truck today? Wash engine! Attached Images

03-20-2013, 06:48 PM	#7224
Trsmotrhed Registered User Join Date: Mar 2012 Location: Pueblo West, Colorado Posts: 430	Re: What did you do to your truck today? Actually this weekend, made my track arm bracket and mounted to frame. Installed rear sway bar. Posted via Mobile Device __________________ Sold the 63 and have a 68 now. 63 SWB C10 LT1/4L60E, PS, PB, Disk Brakes, CPP 4" drop coil rear, 2.5" drop spindle w/ 1" drop coil. slotted rotors, front and rear sway bars. 18"x8" Cragar SS w/ 245/45R18 http://67-72chevytrucks.com/vboard/s...d.php?t=544174

03-22-2013, 01:39 PM	#7225
keeks69 Registered User Join Date: Feb 2013 Location: Port Huron Michigan Posts: 37	Re: What did you do to your truck today? Finished this today looks pretty good just waiting for the new clear glass part! Attached Images

Register or Log In To remove these advertisements.