![]() |
![]() |
#51 |
Registered User
Join Date: Dec 2006
Location: Calgary, Canada
Posts: 54
|
Re: My Pro Street '56 GMC Pick'em Up
BC Toy Chest,
In post #35, the photo of your cool new battery box reveals something about the setup of your welder. It appears that the polarity of the welder is backwards. I was using flux-core wire on a MIG welder that setup for gas welding. It took me a month to figure out why the welds looked like spaghetti. If you don't have a polarity problem then the shielding gas isn't doing its job. Nevertheless, cool project Man! Z |
![]() |
![]() |
![]() |
#52 |
Registered User
Join Date: Nov 2010
Location: SoCal
Posts: 914
|
Re: My Pro Street '56 GMC Pick'em Up
ezekiel said:
BC Toy Chest, In post #35, the photo of your cool new battery box reveals something about the setup of your welder. It appears that the polarity of the welder is backwards. I was using flux-core wire on a MIG welder that setup for gas welding. It took me a month to figure out why the welds looked like spaghetti. If you don't have a polarity problem then the shielding gas isn't doing its job. Nevertheless, cool project Man! Z Hey ezekiel That is a result of ugly welding. HAHAHA, I have it set up correctly, and was using my gas I have good days and I have bad days still new to welding. This welder unlike some others came set up for gas and I did not have to reveres the polarity. Believe me I have been out of gas before and I know the difference with spitting and splater. My problem was trying to be sure I was getting good penetration while joining the two metals together at a 90 degree angle. The plates are only .125" thick but I was still a little intimidated by the thickness. But hey ![]() ![]() Thanks for the copliment on my project btw.
__________________
I'm not tail-gating, I'm drafting. ![]() http://67-72chevytrucks.com/vboard/s...d.php?t=432758 Last edited by BC Toy chest; 12-08-2010 at 05:13 PM. |
![]() |
![]() |
![]() |
#53 |
Certified Car Nut
Join Date: Jan 2005
Location: Inglewood, California
Posts: 3,118
|
Re: My Pro Street '56 GMC Pick'em Up
Shhhhhhhhhhhhhhhhhhh. Don't tell people I let you touch my welder, they may think we are friends.lol
|
![]() |
![]() |
![]() |
#54 | |
Registered User
Join Date: Nov 2010
Location: SoCal
Posts: 914
|
Re: My Pro Street '56 GMC Pick'em Up
Quote:
![]() ![]() ![]() ![]()
__________________
I'm not tail-gating, I'm drafting. ![]() http://67-72chevytrucks.com/vboard/s...d.php?t=432758 |
|
![]() |
![]() |
![]() |
#55 |
Certified Car Nut
Join Date: Jan 2005
Location: Inglewood, California
Posts: 3,118
|
Re: My Pro Street '56 GMC Pick'em Up
That's why I'm not helping you, and you wonder why you don't have any friends.lol Remember you are the one that don't have friends, I only hang around to remind you that you are human.lol
|
![]() |
![]() |
![]() |
#56 | |
Registered User
Join Date: Nov 2010
Location: SoCal
Posts: 914
|
Re: My Pro Street '56 GMC Pick'em Up
Quote:
![]()
__________________
I'm not tail-gating, I'm drafting. ![]() http://67-72chevytrucks.com/vboard/s...d.php?t=432758 |
|
![]() |
![]() |
![]() |
#57 |
Registered User
Join Date: Nov 2010
Location: SoCal
Posts: 914
|
Re: My Pro Street '56 GMC Pick'em Up
The last cruz nite before I take the truck back apart. If I had the money I would take my truck to a shop to have the lower hinge pockets replaced. OHH well that aint gona happen any time soon, so I set out to do it myself.
__________________
I'm not tail-gating, I'm drafting. ![]() http://67-72chevytrucks.com/vboard/s...d.php?t=432758 |
![]() |
![]() |
![]() |
#58 |
Registered User
Join Date: Nov 2010
Location: SoCal
Posts: 914
|
Re: My Pro Street '56 GMC Pick'em Up
The last cruz nite before I take the truck back apart. If I had the money I would take my truck to a shop to have the rocker panels & lower hinge pockets replaced. OHH well that aint gona happen any time soon, so I set out to do it myself.
__________________
I'm not tail-gating, I'm drafting. ![]() http://67-72chevytrucks.com/vboard/s...d.php?t=432758 Last edited by BC Toy chest; 12-10-2010 at 01:48 AM. |
![]() |
![]() |
![]() |
#59 |
Certified Car Nut
Join Date: Jan 2005
Location: Inglewood, California
Posts: 3,118
|
Re: My Pro Street '56 GMC Pick'em Up
Kirk is going to be mad at you for putting all these pics of his Panel on a Chevy site.lol So now I can tell him the only thing right about him owning a ford is that it has pics on the best Chevy Truck site on the net.lol
You know how I feel about shops, do it yourself you are better off. You have cutoff wheels and a welder and talking about taking something to a shop. Have you lost your mind.lol Last edited by Kabwe; 12-09-2010 at 07:53 PM. |
![]() |
![]() |
![]() |
#60 |
Registered User
Join Date: Mar 2010
Location: tucson az.
Posts: 45
|
Re: My Pro Street '56 GMC Pick'em Up
nice truck and nice build. subscribed.
__________________
Project "Abby" 84 swb 6.0 swap and rebuild. http://67-72chevytrucks.com/vboard/s...d.php?t=395121 |
![]() |
![]() |
![]() |
#61 |
Registered User
Join Date: Nov 2010
Location: SoCal
Posts: 914
|
Re: My Pro Street '56 GMC Pick'em Up
Thanks for droppin in americanmuscle.
![]()
__________________
I'm not tail-gating, I'm drafting. ![]() http://67-72chevytrucks.com/vboard/s...d.php?t=432758 |
![]() |
![]() |
![]() |
#62 | |
Registered User
Join Date: Nov 2010
Location: SoCal
Posts: 914
|
Re: My Pro Street '56 GMC Pick'em Up
Quote:
![]() ![]() ![]() Yes I know how you feel about shops you have made your self loud and clear..... "No shop is going to treat your ride the way you would" and your other favorite saying........" if you want it done right you gotta do it your self ". For me the hinge pocket and rocker panels and cab corners seemed pretty complex, then when a couple of shops told me between $780 -$1000 for a single hinge pocket, I said ohhh that doesn't look so hard, ![]()
__________________
I'm not tail-gating, I'm drafting. ![]() http://67-72chevytrucks.com/vboard/s...d.php?t=432758 Last edited by BC Toy chest; 12-10-2010 at 03:19 AM. |
|
![]() |
![]() |
![]() |
#63 |
Registered User
Join Date: Nov 2010
Location: SoCal
Posts: 914
|
Re: My Pro Street '56 GMC Pick'em Up
Before there were patch panels there was lots and lots of bondo
![]() ![]() ![]() I used rivets to hold the rocker panel steady so I could weld it to the step then used my cut off wheel and drill with sanding disc to smooth out the welds.
__________________
I'm not tail-gating, I'm drafting. ![]() http://67-72chevytrucks.com/vboard/s...d.php?t=432758 |
![]() |
![]() |
![]() |
#64 |
Registered User
Join Date: Nov 2010
Location: SoCal
Posts: 914
|
Re: My Pro Street '56 GMC Pick'em Up
For me the hinge pockets and rocker panels and cab corners seemed pretty complex, then when a couple of shops told me between $780 -$1000 for a single hinge pocket, I said ohhh that doesn't look so hard, hahahaha
![]()
__________________
I'm not tail-gating, I'm drafting. ![]() http://67-72chevytrucks.com/vboard/s...d.php?t=432758 Last edited by BC Toy chest; 12-10-2010 at 03:34 AM. |
![]() |
![]() |
![]() |
#65 |
Senior Member
![]() Join Date: Nov 2008
Location: Fannystelle, Manitoba, Canada
Posts: 849
|
Re: My Pro Street '56 GMC Pick'em Up
Nice work.
__________________
Jean-Marc Lacasse 57 GMC 55 GMC 55 Belair 99 S10 http://67-72chevytrucks.com/vboard/s...d.php?t=316140 http://67-72chevytrucks.com/vboard/s...d.php?t=806011 |
![]() |
![]() |
![]() |
#66 |
Registered User
Join Date: Aug 2007
Location: Corona, California
Posts: 7,998
|
Re: My Pro Street '56 GMC Pick'em Up
Nice work BC. I know what you mean about shops charging an arm and leg for work. That's why I end up doing it myself also. I'm real lucky on mine as the hinge pockets and cab corners were in good shape. Although there was a bunch more stuff that was shot.
Kim |
![]() |
![]() |
![]() |
#67 |
Tripple Five Fanatic
Join Date: Sep 2006
Location: USA
Posts: 658
|
Re: My Pro Street '56 GMC Pick'em Up
Nice work, you should start adding up how much $$$ you save by listening to the master and doing it youself. When he speaks you have to listen.
Tri5
__________________
1955 Chevy Stepside/LS1 drive train http://67-72chevytrucks.com/vboard/s...d.php?t=371513 |
![]() |
![]() |
![]() |
#68 |
Certified Car Nut
Join Date: Jan 2005
Location: Inglewood, California
Posts: 3,118
|
Re: My Pro Street '56 GMC Pick'em Up
looks like you are doing a good job to me and I'm glad you remembered my sayings.lol I told you, that you could do it, this stuff is not rocket science although some shops charge you like they are building you a rocket.lol
Tri5nerd, I don't know about this master stuff I just know that no one cares about my rides as much as I do, so I would drive a shop crazy if they worked on my car. A guy told me he took his car to a shop that was suppose to great and he went to visit his ride and was totally shocked at the low quality of the repairs and he told the shop owner "Man give me the car back cause I can f*** up sh** myself".lol Thats how I feel I can mess it up myself and I will work harder to try and fix it also. Now I'm not saying that all shops are like this, but I know the ones that I could afford most likely do low quality work.lol Good work= learning to do it yourself, or having a really good friend who has skills and is willing to help, or just having a huge bank account. Last edited by Kabwe; 12-10-2010 at 02:01 PM. |
![]() |
![]() |
![]() |
#69 |
Registered User
Join Date: Nov 2010
Location: SoCal
Posts: 914
|
Re: My Pro Street '56 GMC Pick'em Up
Thanks JML55 , Kim57, Tri5Nerd for the compliments ohhh yes Master metal man Kabwe thank you for your advice,
![]() ![]() ![]() ![]() ![]()
__________________
I'm not tail-gating, I'm drafting. ![]() http://67-72chevytrucks.com/vboard/s...d.php?t=432758 Last edited by BC Toy chest; 12-11-2010 at 02:34 AM. |
![]() |
![]() |
![]() |
#70 |
Registered User
Join Date: Nov 2010
Location: SoCal
Posts: 914
|
Re: My Pro Street '56 GMC Pick'em Up
Way back when I was under the impression I could get the hinge pockets done at a reasonable cost
![]()
__________________
I'm not tail-gating, I'm drafting. ![]() http://67-72chevytrucks.com/vboard/s...d.php?t=432758 |
![]() |
![]() |
![]() |
#71 |
Registered User
Join Date: Nov 2010
Location: SoCal
Posts: 914
|
Re: My Pro Street '56 GMC Pick'em Up
More cutting, fixen & workin' and more KOOL trucks that have crossed my path.
__________________
I'm not tail-gating, I'm drafting. ![]() http://67-72chevytrucks.com/vboard/s...d.php?t=432758 |
![]() |
![]() |
![]() |
#72 |
Registered User
Join Date: Nov 2010
Location: SoCal
Posts: 914
|
Re: My Pro Street '56 GMC Pick'em Up
More cutting, fixen & workin' and more KOOL trucks that have crossed my path.
__________________
I'm not tail-gating, I'm drafting. ![]() http://67-72chevytrucks.com/vboard/s...d.php?t=432758 Last edited by BC Toy chest; 12-12-2010 at 06:55 AM. |
![]() |
![]() |
![]() |
#73 |
Registered User
Join Date: Nov 2010
Location: SoCal
Posts: 914
|
Re: My Pro Street '56 GMC Pick'em Up
More cutting, fixen & workin' and more KOOL trucks that have crossed my path.
__________________
I'm not tail-gating, I'm drafting. ![]() http://67-72chevytrucks.com/vboard/s...d.php?t=432758 |
![]() |
![]() |
![]() |
#74 |
Registered User
Join Date: Oct 2009
Location: Broken Arrow, OK
Posts: 1,220
|
Re: My Pro Street '56 GMC Pick'em Up
A man has to be really secure in his masculinity to drive a truck that color! Super nice nice trucks AND metal working.
__________________
56 GMC BUILD THREAD: http://67-72chevytrucks.com/vboard/s...d.php?t=368649 69 long bed Chevy turned 67 gmc jimmy roadster: https://67-72chevytrucks.com/vboard/...d.php?t=851167 |
![]() |
![]() |
![]() |
#75 |
Registered User
Join Date: Sep 2009
Location: Albuquerque, NM
Posts: 540
|
Re: My Pro Street '56 GMC Pick'em Up
Really nice work and such a fast pace! You'll probably have your truck done in no time.
__________________
FAT MIKE My 59 http://67-72chevytrucks.com/vboard/s...d.php?t=400201 My 47 http://67-72chevytrucks.com/vboard/s...d.php?t=386848 |
![]() |
![]() |
![]() |
Bookmarks |
|
|