The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1969 - 1972 Blazers and Jimmys Message Board > 1969 - 1972 Blazers and Jimmys Projects and Builds

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 03-10-2018, 07:34 PM   #1
hgs_notes
GEARHEAD
 
hgs_notes's Avatar
 
Join Date: Aug 2003
Location: MN
Posts: 6,120
Re: Junkyard Jimmy Super Low Buck Build Thread

In order to change any tube angles I needed to get a 2" die set. I shopped around because they are pretty spendy. I got the woodward Fab one from summit racing to see if it would work. I didn't really know because the bender was designed to use the dies from pro-tools or JD Squared. The woodward fab set is about $100 cheaper so worth a shot since it's not something I would be using a lot.


The first problem was the main pivot hole is supposed to be 1". It was NOT well machined. The pin just jammed in the end. I don't have a 1" drill bit. I checked with the town mechanic and he steered me to a guy south of town that would. Incredible shop on this farm about a mile or so from me. He specializes in restoring indian motorcycles and cushmans, among other things. He has everything I hope to have for my own future shop and then some. Anyway, he helped me out by boring out the hole. Didn't take much but still a PITA.

So then the next problem was that the other holes in the die have a slightly different spacing. By about 1/16". I don't know if that's by design or just poor quality control. They are a 7/8" hole and the rods would go through ok but there was just enough misalignment in the bender that the pin wouldn't go through. The easiest fix was to pick up a couple 3/4" grade 8 bolts. The holes in the bender itself need some redrilling too so it wasn't just the die. I was able to get the die installed and it worked ok, but has a little free play that wouldn't be there with the 7/8" pins holding it.


I pulled out the passenger side bar and set it up to put just a small bend in just behind the windshield post bend. It turned out ok. I had to recut the notch and I shortened it about an inch on that back end and about 3/8" on the bottom front end. Other than my notch being off a few degrees I'm good with how it turned out.


It's about 3-1/2" outboard of where I had it. Now I just need to try and copy that for the driver side.


After I get this section done I need to decide if I want to raise the body a bit before I make up the tubes that will tie in from underneath and attach to the frame rails. I think an inch or so would be good but don't think it's necessary. And I need to finish getting the rear springs and gas tank out of the way.
hgs_notes is offline   Reply With Quote
Old 03-13-2018, 08:24 PM   #2
Dieselwrencher
6>8 Plugless........
 
Dieselwrencher's Avatar
 
Join Date: Sep 2007
Location: Prairie City, Ia
Posts: 17,140
Re: Junkyard Jimmy Super Low Buck Build Thread

That is looking better and that does stink about the new die but at least you found a new source close to you for weird issues. That is worth it right there!
__________________
Ryan
1972 Chevy Longhorn K30 Cheyenne Super, 359 Inline 6 cylinder, Auto Trans, Tilt, Diesel Tach/Vach, Buckets, Rare Rear 4-link and air ride option Build Thread
1972 GMC Sierra Grande Longhorn 4x4
1972 Chevy Cheyenne Super K20 Long Step side tilt, tach, tow hooks, AC, 350 4 speed
1972 C10 Suburban Custom Deluxe
1969 Chevy milk truck
1971 Camaro RS 5.3 BTR STG3 Cam Super T10
1940 Ford 354 Hemi 46RH Ford 9" on air ride huge project


Tired of spark plugs? Check this out.
Dieselwrencher is offline   Reply With Quote
Old 03-18-2018, 12:10 PM   #3
hgs_notes
GEARHEAD
 
hgs_notes's Avatar
 
Join Date: Aug 2003
Location: MN
Posts: 6,120
Re: Junkyard Jimmy Super Low Buck Build Thread

I finally got some shop time to get the driver side door tube bent. It turned out better than the passenger side for fit.


Pretty happy with this. I need to redo the cross bar behind the windshield though because it's too short now. I'll be able to reuse that tube for frame tie ins, etc.
hgs_notes is offline   Reply With Quote
Old 03-19-2018, 07:21 PM   #4
Dieselwrencher
6>8 Plugless........
 
Dieselwrencher's Avatar
 
Join Date: Sep 2007
Location: Prairie City, Ia
Posts: 17,140
Re: Junkyard Jimmy Super Low Buck Build Thread

That is looking really nice!
__________________
Ryan
1972 Chevy Longhorn K30 Cheyenne Super, 359 Inline 6 cylinder, Auto Trans, Tilt, Diesel Tach/Vach, Buckets, Rare Rear 4-link and air ride option Build Thread
1972 GMC Sierra Grande Longhorn 4x4
1972 Chevy Cheyenne Super K20 Long Step side tilt, tach, tow hooks, AC, 350 4 speed
1972 C10 Suburban Custom Deluxe
1969 Chevy milk truck
1971 Camaro RS 5.3 BTR STG3 Cam Super T10
1940 Ford 354 Hemi 46RH Ford 9" on air ride huge project


Tired of spark plugs? Check this out.
Dieselwrencher is offline   Reply With Quote
Old 03-31-2018, 05:49 PM   #5
hgs_notes
GEARHEAD
 
hgs_notes's Avatar
 
Join Date: Aug 2003
Location: MN
Posts: 6,120
Re: Junkyard Jimmy Super Low Buck Build Thread

Quote:
Originally Posted by Dieselwrencher View Post
That is looking really nice!
Thanks, I haven't done much on it lately, until today anyway. I started out by tack welding those side bars between the rear and middle hoops, no real drama there. Then I started working on the front stuff by drilling holes in the front floor for the foot pads to bolt down to. Once those were set I tack welded the front side bars into place. I might end up notching the passenger side tube where the glove box door hits it. I could also just trim the corner of the glove box door. Either way, it'll need a little work.

Then I made the bar to run behind the windshield frame between the 2 sides. It fit ok and leaves plenty of room to use the visors. The next piece will be the dash bar and door bars.
hgs_notes is offline   Reply With Quote
Old 04-02-2018, 11:40 PM   #6
TennesseeZ
Countdown Survivor
 
TennesseeZ's Avatar
 
Join Date: Aug 2007
Location: Bean Station, East Tennessee
Posts: 9,676
Re: Junkyard Jimmy Super Low Buck Build Thread

Mike, you're becoming quite the tubing fabricator, does my heart good now that l can't do it anymore. I really enjoy following your threads, all of them. Now get out there and get busy lol!
__________________
93 Yukon
89 Silverado Z71 SWB Sport
91 K 2500 Silverado "Lobuk-Worktruk"

A MAN OF HONOR DOES NOT LIE, CHEAT, OR STEAL, NOR TOLERATE THOSE WHO DO.

Gettin' old ain't for sissies.
TennesseeZ is offline   Reply With Quote
Old 04-03-2018, 07:10 AM   #7
Low Elco
Registered User
 
Join Date: Apr 2003
Location: Indep, MO
Posts: 5,893
Re: Junkyard Jimmy Super Low Buck Build Thread

Looks good! I lost track of this one!
Low Elco is offline   Reply With Quote
Old 04-16-2018, 07:35 PM   #8
hgs_notes
GEARHEAD
 
hgs_notes's Avatar
 
Join Date: Aug 2003
Location: MN
Posts: 6,120
Re: Junkyard Jimmy Super Low Buck Build Thread

Wish I had more progress to post but I haven't worked on it a lot. Several reasons for that, like blizzards and the clean up afterwards, this whole job thing, spending time with the wife, etc. Anyway, got the dash tube tacked in. I was going to do the door opening tubes next but figured I should wait until I have seats. That way I can get the seats mounted and have a better idea of where to put those tubes, plus the ones behind the seats for mounting the harnesses. I ordered some seats and harnesses and they should be delivered before I get back home from this trip.


I figured out it would be faster and cheaper to use a cunk of wood in the tube notcher to try out fitting some stuff before cutting the tubes. Worked well. PVC would work great too, but I had a piece of scrap wood that worked for this go around.

Maybe next weekend I'll get more done.
hgs_notes is offline   Reply With Quote
Old 04-22-2018, 09:25 PM   #9
hgs_notes
GEARHEAD
 
hgs_notes's Avatar
 
Join Date: Aug 2003
Location: MN
Posts: 6,120
Re: Junkyard Jimmy Super Low Buck Build Thread

While I was out of town my order came in.


I got the original seats pulled out and the sliders put onto the new seats (they came with sliders, good deal) and sat them in place. They should work great.




Before I pulled out the old seats I took some measurements. I want the new ones a bit lower. Should work out great. I think I have a plan now for where the next tubes will go. I'll have the seat mounts attach to the cage.
hgs_notes is offline   Reply With Quote
Old 04-23-2018, 12:44 AM   #10
MrBeast
high-Tech Red Neck
 
MrBeast's Avatar
 
Join Date: Feb 2008
Location: Livingston, MT/On my boat WA/BC/AK
Posts: 2,294
Re: Junkyard Jimmy Super Low Buck Build Thread

Cage looks a lot better with the alterations you made!

I would consider moving the windshield bar forward as far as possible, it looks as though there is room for the visors to flip up under it.
__________________
"He used to be a pretty nice feller, now he's a welder!"
MrBeast is offline   Reply With Quote
Old 06-11-2018, 11:43 PM   #11
hgs_notes
GEARHEAD
 
hgs_notes's Avatar
 
Join Date: Aug 2003
Location: MN
Posts: 6,120
Re: Junkyard Jimmy Super Low Buck Build Thread

Progress has been slow. Since late April when I last posted it finally started to warm up around here and there was a lot of things around the compound that I was waiting for the thaw so I could get going. I was mainly working on the frame for the seats. A couple weeks ago I got the rear bar fitted in.


Nothing fancy, just a 1-1/4" tube with a 90 on each end to weld to the cage. The front part was more challenging. The seat brackets are 16" front to back. My die has a 5" radius and I measured an earlier bend for reference marks so I knew about where to put the first bend. Turned out fine. I've also been measuring the angle after the bend and where the ram is at in relation to a mark I made on the bender frame so I have an idea of how far to go.


I'm shooting for a 16-1/2" space between the front and rear tubes. Room for 1/8" plates to be welded to the tubes and bolted to the seat brackets. This 90 was the easy part. Next is bending a section that connects to the door tube and drops down to the correct height, which is tricky because the door tube is at a 20* angle so any movement front and back changes the height and the angle that the bend hits that tube is different depending on where it's cut. They meet in the middle of the bend. I only tossed one piece into the scrap pile so not bad. I wasn't going to try and make this in one piece, my math skills are ok, but not that good. I used 1-1/2' tube with 1/8" wall to fit over the 2 pieces.


I did try notching the tube in the bend area but it really didn't work well. I ended up just using a flapper disc on an angle grinder to form the notch. It's not that hard but I'm glad I have the notcher rig anyway. Like my wire brush shims?


So far so good. The passenger side is tacked in place. I am fabbing a little support that will bolt into one of the original seat holes and hold the front inside corner. And I need to cut and drill the plates that will hold the seat brackets. Almost done with the driver side also. Maybe next weekend the seat frame will be done minus the finish welds.






hgs_notes is offline   Reply With Quote
Old 11-11-2018, 06:26 PM   #12
hgs_notes
GEARHEAD
 
hgs_notes's Avatar
 
Join Date: Aug 2003
Location: MN
Posts: 6,120
Re: Junkyard Jimmy Super Low Buck Build Thread

Weather turned to crap so I'm back to working on indoor projects. The Jimmy has been sitting as it was in June. This weekend I bought a new air hammer with more power to chisel off rivets to remove suspension brackets. Even with that it's a lot of work.

Got the fuel tank and hitch out of the way. Wasn't exactly easy because I had the truck resting on the side brackets for the hitch so I had to jack up each side to get the weight off that to remove it. I still need to lift it now that the suspension stuff is out of the way to get the rear stand in a better position to work around.




Took the driver side leaf spring off with the brackets attached. Should have done that on the other side too. Learning as I go.






Time to start figuring out how to tie the cage into the frame.
hgs_notes is offline   Reply With Quote
Old 11-20-2018, 10:44 AM   #13
hgs_notes
GEARHEAD
 
hgs_notes's Avatar
 
Join Date: Aug 2003
Location: MN
Posts: 6,120
Re: Junkyard Jimmy Super Low Buck Build Thread

Sunday I finally got a seat mounted up. Pretty happy about that.




I brought one of the tires in to see how it looks. The truck is sitting at what I believe will be it's normal ride height. This is a used 35" tire and measured about 34".


hgs_notes is offline   Reply With Quote
Old 11-28-2018, 04:53 PM   #14
Dieselwrencher
6>8 Plugless........
 
Dieselwrencher's Avatar
 
Join Date: Sep 2007
Location: Prairie City, Ia
Posts: 17,140
Re: Junkyard Jimmy Super Low Buck Build Thread

Nice work on the cage. It's looking great! How many snows have you had so far this fall?
__________________
Ryan
1972 Chevy Longhorn K30 Cheyenne Super, 359 Inline 6 cylinder, Auto Trans, Tilt, Diesel Tach/Vach, Buckets, Rare Rear 4-link and air ride option Build Thread
1972 GMC Sierra Grande Longhorn 4x4
1972 Chevy Cheyenne Super K20 Long Step side tilt, tach, tow hooks, AC, 350 4 speed
1972 C10 Suburban Custom Deluxe
1969 Chevy milk truck
1971 Camaro RS 5.3 BTR STG3 Cam Super T10
1940 Ford 354 Hemi 46RH Ford 9" on air ride huge project


Tired of spark plugs? Check this out.
Dieselwrencher is offline   Reply With Quote
Old 11-28-2018, 06:12 PM   #15
swamp rat
Registered User
 
swamp rat's Avatar
 
Join Date: Oct 2007
Location: Spanaway
Posts: 8,451
Re: Junkyard Jimmy Super Low Buck Build Thread

Things are taking shape!
__________________
Mike.

Swamp Rat build thread :
http://67-72chevytrucks.com/vboard/s...d.php?t=595019

72 3/4T 4X4
4" BDS Lift
33" BFG's
swamp rat is offline   Reply With Quote
Old 11-28-2018, 06:54 PM   #16
hgs_notes
GEARHEAD
 
hgs_notes's Avatar
 
Join Date: Aug 2003
Location: MN
Posts: 6,120
Re: Junkyard Jimmy Super Low Buck Build Thread

Quote:
Originally Posted by Dieselwrencher View Post
Nice work on the cage. It's looking great! How many snows have you had so far this fall?
4 that I can think of. It melted last week but is snowing now.
Quote:
Originally Posted by swamp rat View Post
Things are taking shape!
Thanks, I'll probably be back out there in the next few days making more progress.
hgs_notes is offline   Reply With Quote
Old 11-27-2020, 01:55 PM   #17
LT7A
Registered User
 
Join Date: Oct 2015
Location: PNW
Posts: 3,545
Re: Junkyard Jimmy Super Low Buck Build Thread

This has been an epic saga. Took days to read it. Epic, not just in the build, but in your overall life, home, etc. Hoping that it continues to go well.
LT7A is offline   Reply With Quote
Old 12-06-2020, 08:19 PM   #18
hgs_notes
GEARHEAD
 
hgs_notes's Avatar
 
Join Date: Aug 2003
Location: MN
Posts: 6,120
Re: Junkyard Jimmy Super Low Buck Build Thread

Quote:
Originally Posted by LT7A View Post
This has been an epic saga. Took days to read it. Epic, not just in the build, but in your overall life, home, etc. Hoping that it continues to go well.
Thanks, it was a hell of a story. And things have continued to go great. Haven't been working on this project much, mainly because of distractions with other projects. Lately I've been working on my new (to me) plow truck. My 76 K10 was falling apart and I found a 78 GMC K35 dually to replace it. It needed work, like every other beater I drag home but it's a pretty solid truck, newly rebuilt motor, runs great. Interior was crap so I refurbed it. And the original Dana 60 had been swapped for a 44 single wheel so it looks wrong. I'm fixing up a 60 now to swap in next summer.

Also this summer I finally got my 79 crewcab running and driving again. The slowest LS swap in history. 5 years! Got the rust repaired on the passenger side of the cab, driver side is next. Should be on the road next summer with a big old camper in the bed!

I'm going to try and get back on this one over the winter. I bought a more powerful welder to handle the suspension work. But I'm finishing up some other things like a little 69 honda CT90, my sons 83 Kawasaki KZ750 LTD and some rust repair on a friends cab.

On a personal note, do you know how you know that you're with the right woman? Spend 8 months working from home and being together every... single... day... and it was the best.
Attached Images
  
hgs_notes is offline   Reply With Quote
Old 12-06-2020, 09:01 PM   #19
Ol Blue K20
Proprietor of Dale's Corner
 
Ol Blue K20's Avatar
 
Join Date: Nov 2012
Location: Vacaville , CA
Posts: 15,910
Re: Junkyard Jimmy Super Low Buck Build Thread

Quote:
Originally Posted by hgs_notes View Post
Thanks, it was a hell of a story. And things have continued to go great. Haven't been working on this project much, mainly because of distractions with other projects. Lately I've been working on my new (to me) plow truck. My 76 K10 was falling apart and I found a 78 GMC K35 dually to replace it. It needed work, like every other beater I drag home but it's a pretty solid truck, newly rebuilt motor, runs great. Interior was crap so I refurbed it. And the original Dana 60 had been swapped for a 44 single wheel so it looks wrong. I'm fixing up a 60 now to swap in next summer.

Also this summer I finally got my 79 crewcab running and driving again. The slowest LS swap in history. 5 years! Got the rust repaired on the passenger side of the cab, driver side is next. Should be on the road next summer with a big old camper in the bed!

I'm going to try and get back on this one over the winter. I bought a more powerful welder to handle the suspension work. But I'm finishing up some other things like a little 69 honda CT90, my sons 83 Kawasaki KZ750 LTD and some rust repair on a friends cab.

On a personal note, do you know how you know that you're with the right woman? Spend 8 months working from home and being together every... single... day... and it was the best.
Wow!! I thought you disappeared HG.....Nice to see ya post
__________________
"Some Days Chickens And Some Days Feathers"

Dale
XNGH ECV Sam Brannan 1004

R.I.P. 67ChevyRedneck
R.I.P. Grumpy Old Man
Ol Blue K20 is offline   Reply With Quote
Old 12-07-2020, 01:01 PM   #20
jaros44sr
Registered User
 
jaros44sr's Avatar
 
Join Date: May 2006
Location: Philadelphia, Pa. 19454
Posts: 9,444
Re: Junkyard Jimmy Super Low Buck Build Thread

me too, how is the panel bond holding up on the pick up, always wanted to try that method

Welcome back, you are an inspiration to all of us on the boards
__________________
Semper Fi...Uncle Sam, you da man

All parts offered to help are free, unless otherwise noted

Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training
SAFETY FIRST

AS usual, off topic

They say your mind goes second, can't remember the first


Jim
jaros44sr is offline   Reply With Quote
Old 12-06-2020, 05:24 PM   #21
FRENCHBLUE72
PROJECT 7DEUCE
 
FRENCHBLUE72's Avatar
 
Join Date: Dec 2002
Location: GRANTS PASS OR
Posts: 21,590
Re: Junkyard Jimmy Super Low Buck Build Thread

Looks great ....keep up the good work
__________________
GO BIG GREEN GO DUCKS



MEMBER #6377

72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free.

Project "7DEUCE"

check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665



Tim Powell..R.I.P EastSideLowlife..... R.I.P..
FRENCHBLUE72 is offline   Reply With Quote
Old 12-10-2020, 03:18 AM   #22
Dieselwrencher
6>8 Plugless........
 
Dieselwrencher's Avatar
 
Join Date: Sep 2007
Location: Prairie City, Ia
Posts: 17,140
Re: Junkyard Jimmy Super Low Buck Build Thread

I'm glad to see everything is going well up there for ya! Hopefully you get all the snow up there this year! LoL
__________________
Ryan
1972 Chevy Longhorn K30 Cheyenne Super, 359 Inline 6 cylinder, Auto Trans, Tilt, Diesel Tach/Vach, Buckets, Rare Rear 4-link and air ride option Build Thread
1972 GMC Sierra Grande Longhorn 4x4
1972 Chevy Cheyenne Super K20 Long Step side tilt, tach, tow hooks, AC, 350 4 speed
1972 C10 Suburban Custom Deluxe
1969 Chevy milk truck
1971 Camaro RS 5.3 BTR STG3 Cam Super T10
1940 Ford 354 Hemi 46RH Ford 9" on air ride huge project


Tired of spark plugs? Check this out.
Dieselwrencher is offline   Reply With Quote
Old 12-13-2020, 12:55 PM   #23
hgs_notes
GEARHEAD
 
hgs_notes's Avatar
 
Join Date: Aug 2003
Location: MN
Posts: 6,120
Re: Junkyard Jimmy Super Low Buck Build Thread

Quote:
Originally Posted by Ol Blue K20 View Post
Wow!! I thought you disappeared HG.....Nice to see ya post
Thanks Dale, glad to see you're still checking in too. I check on the board regularly just haven't been posting. I put a lot of stuff on FB. Look for me there. https://www.facebook.com/michael.wells.988/

Quote:
Originally Posted by jaros44sr View Post
me too, how is the panel bond holding up on the pick up, always wanted to try that method

Welcome back, you are an inspiration to all of us on the boards
The panel bond works great. I've used it on several projects. Every body shop uses it routinely now and so do the manufacturers. The key, as always, is good prep.

Quote:
Originally Posted by Dieselwrencher View Post
I'm glad to see everything is going well up there for ya! Hopefully you get all the snow up there this year! LoL
In October it looked like another whopper of a winter coming but since then it's been mild. And I think it's snowed down your way this weekend. I hope the roads are good by tomorrow because I'm heading that way. I'll be around the Des Moines area the next couple days.

I should probably post an update on the farm truck thread. And I'm going to post a "How to" on refurbishing a truck rear slider window soon.
hgs_notes is offline   Reply With Quote
Old 12-13-2020, 02:00 PM   #24
Ol Blue K20
Proprietor of Dale's Corner
 
Ol Blue K20's Avatar
 
Join Date: Nov 2012
Location: Vacaville , CA
Posts: 15,910
Re: Junkyard Jimmy Super Low Buck Build Thread

[QUOTE=hgs_notes;8849203]Thanks Dale, glad to see you're still checking in too. I check on the board regularly just haven't been posting. I put a lot of stuff on FB. Look for me there. https://www.facebook.com/michael.wells.988/

This is as close to social media as I get.....
__________________
"Some Days Chickens And Some Days Feathers"

Dale
XNGH ECV Sam Brannan 1004

R.I.P. 67ChevyRedneck
R.I.P. Grumpy Old Man
Ol Blue K20 is offline   Reply With Quote
Old 12-15-2020, 07:05 AM   #25
Dieselwrencher
6>8 Plugless........
 
Dieselwrencher's Avatar
 
Join Date: Sep 2007
Location: Prairie City, Ia
Posts: 17,140
Re: Junkyard Jimmy Super Low Buck Build Thread

It did snow down here as I'm sure you've seen if you're already down here. If you're still in the area and have some free time, give me a ring. Maybe we can shoot the breeze again!
__________________
Ryan
1972 Chevy Longhorn K30 Cheyenne Super, 359 Inline 6 cylinder, Auto Trans, Tilt, Diesel Tach/Vach, Buckets, Rare Rear 4-link and air ride option Build Thread
1972 GMC Sierra Grande Longhorn 4x4
1972 Chevy Cheyenne Super K20 Long Step side tilt, tach, tow hooks, AC, 350 4 speed
1972 C10 Suburban Custom Deluxe
1969 Chevy milk truck
1971 Camaro RS 5.3 BTR STG3 Cam Super T10
1940 Ford 354 Hemi 46RH Ford 9" on air ride huge project


Tired of spark plugs? Check this out.
Dieselwrencher is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 03:05 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com