Custom Chassis with canti setup - Page 7 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

westsydetrucknrod · 01-11-2006, 07:23 PM

Frame looks awesome!! Nice work

cornutz · 01-12-2006, 02:56 PM

Hey Jr... that shiznit looks sweeeet! I likey alot! By the way, the testosterone levels have FINALLY increased in our household!!!! Thats right, daddies swimmers have produced a male offspring!

Now I just have to await the dreaded snip-snip myself...

Bill G

pharcydekm · 01-13-2006, 12:40 PM

Congrats on your baby boy!!!

bshelton · 01-13-2006, 07:46 PM

cornutz-or is it nonutz? congrats on your last!

*72CSTC5* · 01-14-2006, 04:39 AM

Cornutz, if they cut your nutz I think Valley could weld you up some improved nutz out of steel. Or, maybe after driving your truck with that frame under it you do not need any nutz, they just assume you have big ones.

Izzy · 01-15-2006, 07:38 PM

Best looking chassis I've seen, hands down.

XXL · 01-19-2006, 09:26 PM

Any thoughts on this relatively simple back half? It would tie into the stock frame rails just under the cab.

And... any suggestions on something a little more lift-capable than bags in the stock locations? I don't know that I need something as complicated as valleycustom is doing here...

valleycustom · 01-23-2006, 01:02 PM

Quote:

Originally Posted by XXL

Any thoughts on this relatively simple back half? It would tie into the stock frame rails just under the cab.

And... any suggestions on something a little more lift-capable than bags in the stock locations? I don't know that I need something as complicated as valleycustom is doing here...

Sorry for the delay on responding. I would change the 2x3 rails to 2x4. 2x3 box doesn't look right on a fullsize. It looks to small.

XXL · 01-23-2006, 10:52 PM

Quote:

Originally Posted by valleycustom

Sorry for the delay on responding. I would change the 2x3 rails to 2x4. 2x3 box doesn't look right on a fullsize. It looks to small.

Thanks. It looks like 2x4 is about the same price as well.

Chevy_68 · 01-24-2006, 02:17 AM

Damn that frame is sick man... Keep up the bad ass fab. work man

valleycustom · 01-25-2006, 12:35 AM

Well today I started on the exhaust. I was able to get most of one side finished. When I start on the other side the two pipes in the middle will goin to create a x over pipe. Enjoy

valleycustom · 01-25-2006, 12:36 AM

Some more

FirstGen · 01-25-2006, 01:51 AM

are you using a V-band clamp there? expensive stuff but way nice!

**FRENCHBLUE72** · 01-25-2006, 08:37 AM

Damn that is looking sweeet...

valleycustom · 01-25-2006, 12:17 PM

Quote:

Originally Posted by FirstGen

are you using a V-band clamp there? expensive stuff but way nice!

Yeah those are v band clamps

XXL · 01-25-2006, 09:54 PM

Is the exhaust tude welded to the frame???

pebbleboy · 01-25-2006, 09:58 PM

looks more like a notch in the frame for the exhaust.

valleycustom · 01-25-2006, 09:59 PM

Quote:

Originally Posted by XXL

Is the exhaust tude welded to the frame???

Dude that is an insult even asking that.

J/K No I had to open the frame up so I can get the tubing through. What you see are the welds holding the patch I made to close the DOM back up.h

valleycustom · 01-25-2006, 10:06 PM

Here are some close up pictures. I'm not finished welding it up.

**FRENCHBLUE72** · 01-25-2006, 10:23 PM

That is gonna be a tight azz fit...

valleycustom · 01-25-2006, 11:07 PM

Quote:

Originally Posted by FRENCHBLUE72

That is gonna be a tight azz fit...

It has a 1/2" all the way around. That should be enough once I get the hangers installed.

72MARIO · 01-26-2006, 12:40 AM

That looks great. Nice work. I used the same manderals to do my 3". Not as trick though....I only have a 1/4" around the frame to 3" tube and it never hits. I have poly motor mounts and tranny mount so there is not much motor twist.

I wish I could have got a X pipe in there but the H will be alot more doable. It's kinda going to be more of a U because of where the duals are placed right now there is no horizontal connection that could work..

a squarecan · 01-26-2006, 02:26 AM

All I have to ask is; Is there anything you can't do?

I think I couldnt be more amazed after each set of pix you post, but everytime I find myself more amazed! Very nice work! Did you bend all your exhaust or are they pre-bent pieces? If you did it your self what gauge steel did you run?

Keith

pharcydekm · 01-26-2006, 12:00 PM

LOOKS GOOD! My only question is why not run it straight and go through the frame up ahead rather than make that 90 turn to come through?

el curioso · 01-26-2006, 01:02 PM

Quote:

My only question is why not run it straight and go through the frame up ahead rather than make that 90 turn to come through?

Cuz That would make it to easy and whats a wild frame with a straight exhaust?

01-11-2006, 07:23 PM	#151
westsydetrucknrod Westsyde Truck & Rod Join Date: Jan 2006 Location: Fresno Posts: 17	Re: Custom Chassis with canti setup Frame looks awesome!! Nice work

01-12-2006, 02:56 PM	#152
cornutz All Praise RANDY!! Join Date: Sep 2004 Location: Central California Posts: 391	Re: Custom Chassis with canti setup Hey Jr... that shiznit looks sweeeet! I likey alot! By the way, the testosterone levels have FINALLY increased in our household!!!! Thats right, daddies swimmers have produced a male offspring! Now I just have to await the dreaded snip-snip myself... Bill G

01-13-2006, 12:40 PM	#153
pharcydekm Registered User Join Date: May 2003 Location: Englewood, CO Posts: 146	Re: Custom Chassis with canti setup Congrats on your baby boy!!!

01-13-2006, 07:46 PM	#154
bshelton Registered User Join Date: Jan 2006 Location: Modesto, CA Posts: 13	Re: Custom Chassis with canti setup cornutz-or is it nonutz? congrats on your last!

01-14-2006, 04:39 AM	#155
72CSTC5 Account Suspended Join Date: Nov 2004 Location: Deer Park, Tx. Posts: 2,524	Re: Custom Chassis with canti setup Cornutz, if they cut your nutz I think Valley could weld you up some improved nutz out of steel. Or, maybe after driving your truck with that frame under it you do not need any nutz, they just assume you have big ones.

01-15-2006, 07:38 PM	#156
Izzy Trucker. Join Date: Nov 2002 Location: Fort Worth, TX Posts: 1,364	Re: Custom Chassis with canti setup Best looking chassis I've seen, hands down. Last edited by Izzy; 01-15-2006 at 07:38 PM.

01-19-2006, 09:26 PM	#157
XXL Señor Member Join Date: May 2002 Location: Edge of the world Posts: 5,367	Re: Custom Chassis with canti setup Any thoughts on this relatively simple back half? It would tie into the stock frame rails just under the cab. And... any suggestions on something a little more lift-capable than bags in the stock locations? I don't know that I need something as complicated as valleycustom is doing here... __________________ Craigslist \| ebay \| Engrishtees \| www.myattitudesucks.com \| Follow me on Twitter Last edited by XXL; 10-17-2007 at 12:52 AM.

01-24-2006, 02:17 AM	#160
Chevy_68 Registered User Join Date: Mar 2002 Location: PHX Az Posts: 155	Re: Custom Chassis with canti setup Damn that frame is sick man... Keep up the bad ass fab. work man

01-25-2006, 12:35 AM	#161
valleycustom Registered User Join Date: Mar 2005 Location: Modesto, Ca Posts: 225	Re: Custom Chassis with canti setup Well today I started on the exhaust. I was able to get most of one side finished. When I start on the other side the two pipes in the middle will goin to create a x over pipe. Enjoy Attached Images __________________ Please become a site supporting vendor to advertise a business in your signature. you can do so here Last edited by valleycustom; 01-25-2006 at 12:38 AM.

01-25-2006, 12:36 AM	#162
valleycustom Registered User Join Date: Mar 2005 Location: Modesto, Ca Posts: 225	Re: Custom Chassis with canti setup Some more Attached Images __________________ Please become a site supporting vendor to advertise a business in your signature. you can do so here

01-25-2006, 01:51 AM	#163
FirstGen Just Don't Stop! Join Date: Feb 2004 Location: Dallas Posts: 1,239	Re: Custom Chassis with canti setup are you using a V-band clamp there? expensive stuff but way nice! __________________ 1968 C10 build in process TT LSA/6L90e/9"

01-25-2006, 08:37 AM	#164
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,590	Re: Custom Chassis with canti setup Damn that is looking sweeet... __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

01-25-2006, 09:54 PM	#166
XXL Señor Member Join Date: May 2002 Location: Edge of the world Posts: 5,367	Re: Custom Chassis with canti setup Is the exhaust tude welded to the frame??? Attached Images __________________ Craigslist \| ebay \| Engrishtees \| www.myattitudesucks.com \| Follow me on Twitter

01-25-2006, 10:06 PM	#169
valleycustom Registered User Join Date: Mar 2005 Location: Modesto, Ca Posts: 225	Re: Custom Chassis with canti setup Here are some close up pictures. I'm not finished welding it up. Attached Images __________________ Please become a site supporting vendor to advertise a business in your signature. you can do so here Last edited by valleycustom; 01-25-2006 at 10:07 PM.

01-25-2006, 10:23 PM	#170
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,590	Re: Custom Chassis with canti setup That is gonna be a tight azz fit... __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..



Register or Log In To remove these advertisements.

01-26-2006, 12:40 AM	#172
72MARIO Registered User Join Date: Nov 2000 Location: Huntsville Ontario Canada Posts: 4,052	Re: Custom Chassis with canti setup That looks great. Nice work. I used the same manderals to do my 3". Not as trick though....I only have a 1/4" around the frame to 3" tube and it never hits. I have poly motor mounts and tranny mount so there is not much motor twist. I wish I could have got a X pipe in there but the H will be alot more doable. It's kinda going to be more of a U because of where the duals are placed right now there is no horizontal connection that could work.. __________________ 1968 Suburban numbers matching all original truck now equipped with 6.0/4L80 on Accuair http://67-72chevytrucks.com/vboard/s...d.php?t=625017 1967 C/20 6.0/4L80 Roofing Truck 1990 V2500 Suburban "Plow Truck" 2005 TAHOE DD

01-26-2006, 02:26 AM	#173
a squarecan Registered User Join Date: Mar 2004 Location: Portland, Oregon Posts: 232	Re: Custom Chassis with canti setup All I have to ask is; Is there anything you can't do? I think I couldnt be more amazed after each set of pix you post, but everytime I find myself more amazed! Very nice work! Did you bend all your exhaust or are they pre-bent pieces? If you did it your self what gauge steel did you run? Keith

01-26-2006, 12:00 PM	#174
pharcydekm Registered User Join Date: May 2003 Location: Englewood, CO Posts: 146	Re: Custom Chassis with canti setup LOOKS GOOD! My only question is why not run it straight and go through the frame up ahead rather than make that 90 turn to come through?

Register or Log In To remove these advertisements.