The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Tools, Shops and Shop Safety

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 04-15-2022, 09:31 PM   #1
Troy Sr
Registered User
 
Troy Sr's Avatar
 
Join Date: Nov 2013
Location: Antioch, Ca.
Posts: 442
Blast Cabinets

Hello All,

While going through 7dee2 (Brett)'s 67 Camaro Build I was looking at his blast cabinet build, I thought I'd like to get some input from those that have one and have maybe modified them. I have the same unit from Harbor Freight and have added some updates. I added the bottom abrasive pickup kit, the foot pedal kit, a new/better nozzle, and a shop vac.

My compressor is a Craftsman 6 1/2 Hp 60 Gal vertical tank, its 240 V, max pressure 125 psi, 15 scfm @ 40 psi and 11 1/2 scfm @ 90 psi.

It does do "ok" blasting sometimes but not always. I have glass beads in it now and I had some black aluminum oxide in it before I updated it. I really want it to remove rust better and faster than it does now. One of the problems i have with it is the glass beads do not settle very well back in to bottom, they stay on the upper edges and stay on the sides of the "funnel" so I have to shake it or beat on it to get it to settle a bit. the other day I saw an electric motor that vibrates it to help.

Does anyone have any ideas to help this cabinet to work better? Also what's the best blast media you use? Thanks for your help!!!
__________________
Take Care
Troy
Troy Sr is offline   Reply With Quote
Old 04-15-2022, 10:39 PM   #2
mongocanfly
Post Whore

 
mongocanfly's Avatar
 
Join Date: May 2015
Location: Alabama
Posts: 14,557
Re: Blast Cabinets

The glass beads are a very fine abrasive... if you want to remove rust better, then get sand..obviously the coarser grit the better..I run 80 and 120 in mine
At work, we use glass beads, we cut some teflon sheets to fit the sides to help it slide down better..moisture also creates problems..so we hang decadent bags under the screen
__________________
Mongo...aka Greg

RIP Dad
RIP Jesse

1981 C30 LQ9 NV4500..http://67-72chevytrucks.com/vboard/s...d.php?t=753598
Mongos AD- LS3 TR6060...http://67-72chevytrucks.com/vboard/s...34#post8522334
Columbus..the 1957 IH 4x4...http://67-72chevytrucks.com/vboard/s...63#post8082563
2023 Chevy Z71..daily driver
mongocanfly is offline   Reply With Quote
Old 04-16-2022, 10:55 AM   #3
Getter-Done
Senior Member
 
Getter-Done's Avatar
 
Join Date: Dec 2009
Location: TN.
Posts: 7,623
Re: Blast Cabinets

For rust removal, I use Aluminum Oxide.
It's the Longest-lasting media for fast, effective rust removal.

Here is a list of other abrasives and their application.

Glass Bead/Works best on softer metals like aluminum, brass and die-cast.

Walnut Shells/Remove paint, carbon deposits from ferrous metal, clean internal parts.

Ground Glass Media Free 40/70 Mesh Non-hazardous silica substitute to use for light rust removal.

Silicon Carbide/Sharp edges for heavy rust removal, welding/brazing prep, glass etching.

Rust Remover Bicarb Soda w/ 10% 70 Grit Alum Oxide/Most aggressive soda for rust removal; 90% soda, 10% alum. oxide.

Now for the media issue not sliding back down, I found a kick drum pedal at a scrap yard one time it works great. You can leave you hands in the gloves and you don't have to knee the cabinet
I also have a small vibration motor on there.
Name:  kickdrumpedal.jpg
Views: 646
Size:  25.5 KB
Name:  vibe.jpg
Views: 702
Size:  95.2 KB
__________________
________________________________________________________________________________________
____________________________________________
84 Chevy K-20
63 Impala (my high school car)

http://67-72chevytrucks.com/vboard/s...Crew Cab Build
Getter-Done is offline   Reply With Quote
Old 04-16-2022, 01:05 PM   #4
mongocanfly
Post Whore

 
mongocanfly's Avatar
 
Join Date: May 2015
Location: Alabama
Posts: 14,557
Re: Blast Cabinets

Love the kick pedal idea..!!..
Where'd you get the vibrator motor...that looks nice..I found a few, but they were on the big size,,,,or 12v
__________________
Mongo...aka Greg

RIP Dad
RIP Jesse

1981 C30 LQ9 NV4500..http://67-72chevytrucks.com/vboard/s...d.php?t=753598
Mongos AD- LS3 TR6060...http://67-72chevytrucks.com/vboard/s...34#post8522334
Columbus..the 1957 IH 4x4...http://67-72chevytrucks.com/vboard/s...63#post8082563
2023 Chevy Z71..daily driver
mongocanfly is offline   Reply With Quote
Old 04-16-2022, 01:12 PM   #5
Getter-Done
Senior Member
 
Getter-Done's Avatar
 
Join Date: Dec 2009
Location: TN.
Posts: 7,623
Re: Blast Cabinets

Mine is a little different.
This is a link for example.

Link: https://www.ebay.com/itm/16431955818...2Cchnl%3Dmkcid
__________________
________________________________________________________________________________________
____________________________________________
84 Chevy K-20
63 Impala (my high school car)

http://67-72chevytrucks.com/vboard/s...Crew Cab Build
Getter-Done is offline   Reply With Quote
Old 04-16-2022, 02:17 PM   #6
mongocanfly
Post Whore

 
mongocanfly's Avatar
 
Join Date: May 2015
Location: Alabama
Posts: 14,557
Re: Blast Cabinets

Thanks..!
I found the one in your pic above..looks like under $45 ..not bad
__________________
Mongo...aka Greg

RIP Dad
RIP Jesse

1981 C30 LQ9 NV4500..http://67-72chevytrucks.com/vboard/s...d.php?t=753598
Mongos AD- LS3 TR6060...http://67-72chevytrucks.com/vboard/s...34#post8522334
Columbus..the 1957 IH 4x4...http://67-72chevytrucks.com/vboard/s...63#post8082563
2023 Chevy Z71..daily driver
mongocanfly is offline   Reply With Quote
Old 04-17-2022, 01:51 PM   #7
Troy Sr
Registered User
 
Troy Sr's Avatar
 
Join Date: Nov 2013
Location: Antioch, Ca.
Posts: 442
Re: Blast Cabinets

Hello again All, I changed out the glass beads with some black iron oxide and man what a difference!!!! I was able to blast my control arms much faster!!! I think the only problem I have now it the piece of crap compressor! Thanks for your help!!!!
__________________
Take Care
Troy
Troy Sr is offline   Reply With Quote
Old 04-17-2022, 10:43 PM   #8
Getter-Done
Senior Member
 
Getter-Done's Avatar
 
Join Date: Dec 2009
Location: TN.
Posts: 7,623
Re: Blast Cabinets

Here is another upgrade I have.

This is a simple short U tube video below.

There are tons of videos on this same upgrade.
It can also be done with Pipe & ball valve from the Box stores.

__________________
________________________________________________________________________________________
____________________________________________
84 Chevy K-20
63 Impala (my high school car)

http://67-72chevytrucks.com/vboard/s...Crew Cab Build
Getter-Done is offline   Reply With Quote
Old 04-29-2022, 10:45 PM   #9
Troy Sr
Registered User
 
Troy Sr's Avatar
 
Join Date: Nov 2013
Location: Antioch, Ca.
Posts: 442
Re: Blast Cabinets

Well today I tore down my Air Compressor and rebuilt it. The cylinders and the seal rings were SHOT!!! I just started it up and it went from 0 psi to 125 psi in less than 5 mins!!! Now I think my blasters gunna kick butt!!!! Yipee!!!!
__________________
Take Care
Troy
Troy Sr is offline   Reply With Quote
Old 04-29-2022, 11:00 PM   #10
Getter-Done
Senior Member
 
Getter-Done's Avatar
 
Join Date: Dec 2009
Location: TN.
Posts: 7,623
Re: Blast Cabinets

Quote:
Originally Posted by Troy Sr View Post
Well today I tore down my Air Compressor and rebuilt it. The cylinders and the seal rings were SHOT!!! I just started it up and it went from 0 psi to 125 psi in less than 5 mins!!! Now I think my blasters gunna kick butt!!!! Yipee!!!!
That is great News
__________________
________________________________________________________________________________________
____________________________________________
84 Chevy K-20
63 Impala (my high school car)

http://67-72chevytrucks.com/vboard/s...Crew Cab Build
Getter-Done is offline   Reply With Quote
Old 06-24-2022, 12:15 PM   #11
doug_p
Registered User
 
doug_p's Avatar
 
Join Date: Sep 2014
Location: Yorktown, VA
Posts: 87
Re: Blast Cabinets

Steel grit also works very well, but if you don't do some "protecting" of the inner cabinet, it will eat through the cabinet also. Rust removal is no issue for steel grit - comes in various grades also, and honestly in my experience lasts far longer than anything else.
doug_p is offline   Reply With Quote
Old 06-24-2022, 10:56 PM   #12
Getter-Done
Senior Member
 
Getter-Done's Avatar
 
Join Date: Dec 2009
Location: TN.
Posts: 7,623
Re: Blast Cabinets

Quote:
Originally Posted by doug_p View Post
Steel grit also works very well, but if you don't do some "protecting" of the inner cabinet, it will eat through the cabinet also. Rust removal is no issue for steel grit - comes in various grades also, and honestly in my experience lasts far longer than anything else.
Yeah

I use a stainless steel Sheild behind what I am blasting.
if I use Steel shot.

With your Idea I may cut some sheets at work to protect my cabinet.
__________________
________________________________________________________________________________________
____________________________________________
84 Chevy K-20
63 Impala (my high school car)

http://67-72chevytrucks.com/vboard/s...Crew Cab Build
Getter-Done is offline   Reply With Quote
Old 06-25-2022, 06:25 AM   #13
doug_p
Registered User
 
doug_p's Avatar
 
Join Date: Sep 2014
Location: Yorktown, VA
Posts: 87
Re: Blast Cabinets

So there is a difference between grit, and shot - you are probably aware. Shot is like small bb's, grit is just that, sharp and angular. They both leave very differing surface prep's once blasted.
We use thick mud flap style rubber material to line the inside of our cabinet at work, usually 3/8".
doug_p is offline   Reply With Quote
Old 06-25-2022, 05:55 PM   #14
Getter-Done
Senior Member
 
Getter-Done's Avatar
 
Join Date: Dec 2009
Location: TN.
Posts: 7,623
Re: Blast Cabinets

Quote:
Originally Posted by doug_p View Post
So there is a difference between grit, and shot - you are probably aware. Shot is like small bb's, grit is just that, sharp and angular. They both leave very differing surface prep's once blasted.
We use thick mud flap style rubber material to line the inside of our cabinet at work, usually 3/8".
That is a great Idea

Eastwood has some good info on different media.

Link: https://www.eastwood.com/abrasive-blasting.html?cat=104

The old guy I send some of my Bigger stuff to, He has Ground up Light switch covers for media.

I just have the simple stuff.
Walnut shell, Steel shot and alum. ox
__________________
________________________________________________________________________________________
____________________________________________
84 Chevy K-20
63 Impala (my high school car)

http://67-72chevytrucks.com/vboard/s...Crew Cab Build
Getter-Done is offline   Reply With Quote
Old 09-14-2022, 09:53 AM   #15
dsraven
Registered User
 
Join Date: Nov 2010
Location: calgary alberta
Posts: 7,771
Re: Blast Cabinets

when I went to pick up some more silica sand for my cabinet blaster, the yard guy asked me what I was using it for. when I told him he asked if I have a cabinet full of powder. I said, well, yeah it doesn't seem to last long. he recommended garnet for cabinet blasters because it doesn't shatter upon the first impact and make powder. I switched over for a bag to test it out. it works better for sure and partially, i think, because it takes more impacts before powdering up
dsraven is offline   Reply With Quote
Old 09-14-2022, 01:56 PM   #16
mr48chev
Registered User
 
mr48chev's Avatar
 
Join Date: Jul 2007
Location: Toppenish, WA
Posts: 15,242
Re: Blast Cabinets

Silica sand isn't good for your lungs either. lot of people use it because it is cheap and easy go get but the dust off it is what causes silicosis.

Media for sand blast cabinets has improved greatly in the past 20 or so years as so many people have blast cabinets at home.

As far as compressors go, it takes a pretty good and big compressor to keep up with any sand blast cabinet with the amount of air they use.
__________________
Founding member of the too many projects, too little time and money club.

My ongoing truck projects:
48 Chev 3100 that will run a 292 Six.
71 GMC 2500 that is getting a Cad 500 transplant.
77 C 30 dualie, 454, 4 speed with a 10 foot flatbed and hoist. It does the heavy work and hauls the projects around.
mr48chev is offline   Reply With Quote
Old 02-10-2023, 11:33 PM   #17
sixty2pcup
Registered User
 
sixty2pcup's Avatar
 
Join Date: Dec 2011
Location: toledo oh
Posts: 12
Re: Blast Cabinets

Some good information. thanks
sixty2pcup is offline   Reply With Quote
Old 02-21-2023, 08:59 PM   #18
cbeerman
Registered User
 
Join Date: Jan 2016
Location: NJ
Posts: 406
Re: Blast Cabinets

+1 on the Garnet and it doesn't absorb moisture
Just regulate your air pressure so it doesn't hit too hard and shatter the media.
cbeerman is offline   Reply With Quote
Old 02-28-2024, 02:12 PM   #19
HO455
Post Whore
 
HO455's Avatar
 
Join Date: Feb 2016
Location: Portland Oregon
Posts: 10,752
Re: Blast Cabinets

Quote:
Originally Posted by cbeerman View Post
+1 on the Garnet and it doesn't absorb moisture
Just regulate your air pressure so it doesn't hit too hard and shatter the media.
What PSI are you running at to achieve that? I would like a ballpark starting point.

Thanks in advance.
__________________
Thanks to Bob and Jeanie and everyone else at Superior Performance for all their great help.
RIP Bob Parks.
1967 Burban the WMB,1991 S(stink)-10 Blazer,1969 GTO, 1970 Javelin, 1952 F2 Ford 4X4, 29 Model A, 72 Firebird. 85 Alfa Romeo
If it breaks I didn't want it in the first place
The WMB repair thread http://67-72chevytrucks.com/vboard/s...d.php?t=698377
HO455 is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 05:48 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com