The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1967 - 1972 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 12-04-2022, 10:32 AM   #1
saxart
Registered User
 
saxart's Avatar
 
Join Date: Aug 2012
Location: St. Croix River Valley, WI
Posts: 795
Can temperature gauge be adjusted?

This past summer I was driving down the road and started hearing a fast ticking noise from somewhere inside the cab. Long story short, it was the temp gauge. The needle was slamming from high to low over and over and over until I pulled over, popped the hood and found that the temp gauge wire had disconnected itself from the sensor and was grounding out on the engine block.

After reconnecting the wire, the gauge now reads very low even when the engine is up to operating temp.



Is there a way to adjust these gauges so it reads at the right spot when the engine is warm, or do I need to replace the original gauge?
__________________
Meet "Old Roy": http://67-72chevytrucks.com/vboard/s...d.php?t=707801
saxart is offline   Reply With Quote
Old 12-04-2022, 12:26 PM   #2
68 C10 Driver
Senior Member
 
Join Date: Oct 2020
Location: Kathleen, GA
Posts: 615
Re: Can temperature gauge be adjusted?

As inexpensive as the gauges are, I would just replace it.
68 C10 Driver is offline   Reply With Quote
Old 12-04-2022, 01:15 PM   #3
Accelo
Senior Member
 
Accelo's Avatar
 
Join Date: Mar 2015
Location: washington
Posts: 2,145
Re: Can temperature gauge be adjusted?

A lot of people add resistance to the sensor wire to "re-calibrate" the gauge. It only works when the gauge reads high. I suspect the wild gyrations moved the needle on the stem.
Least expensive option will likely be replacing the gauge as 68 recommended.
Accelo is offline   Reply With Quote
Old 12-04-2022, 01:37 PM   #4
Palf70Step
State of Confusion!

 
Palf70Step's Avatar
 
Join Date: Jul 2002
Location: Gulfport, MS USA
Posts: 46,575
Re: Can temperature gauge be adjusted?

Make sure your sending unit is good before you do the gauge. IT's a cheaper fix to begin with.
__________________
Bill
1970 Chevy Custom/10 LWB Fleetside
2010 Toyota Tacoma PreRunner SR5 Double Cab - DD

Member of Louisiana Classic Truck Club (LCTC)

Bill's Gallery
Life isn't tied with a bow, but it's still a gift.
Live simply. Love generously. Care deeply. Speak kindly. Leave the rest to God!
Palf70Step is offline   Reply With Quote
Old 12-04-2022, 03:03 PM   #5
Steeveedee
Who Changed This?
 
Steeveedee's Avatar
 
Join Date: Jan 2013
Location: Simi Valley, CA
Posts: 10,019
Re: Can temperature gauge be adjusted?

Quote:
Originally Posted by Accelo View Post
A lot of people add resistance to the sensor wire to "re-calibrate" the gauge. It only works when the gauge reads high. I suspect the wild gyrations moved the needle on the stem.
Least expensive option will likely be replacing the gauge as 68 recommended.
Bolding mine. This.
__________________
~Steven

'70 Chevy 3/4T Longhorn CST 402/400/3.56 Custom Camper

Simi Valley, CA
Steeveedee is offline   Reply With Quote
Old 12-04-2022, 03:57 PM   #6
Accelo
Senior Member
 
Accelo's Avatar
 
Join Date: Mar 2015
Location: washington
Posts: 2,145
Re: Can temperature gauge be adjusted?

Made the assumption the sensor was good as it was before the wire came off.
Not a guarantee it's good guess in my opinion.
Accelo is offline   Reply With Quote
Old 12-05-2022, 02:04 PM   #7
mrein3
Registered User
 
mrein3's Avatar
 
Join Date: Feb 2000
Location: Center City, MN, USA
Posts: 3,253
Re: Can temperature gauge be adjusted?

Quote:
Originally Posted by saxart View Post
This past summer I was driving down the road and started hearing a fast ticking noise from somewhere inside the cab. Long story short, it was the temp gauge. The needle was slamming from high to low over and over and over until I pulled over, popped the hood and found that the temp gauge wire had disconnected itself from the sensor and was grounding out on the engine block.

After reconnecting the wire, the gauge now reads very low even when the engine is up to operating temp.

picture snipped out

Is there a way to adjust these gauges so it reads at the right spot when the engine is warm, or do I need to replace the original gauge?
Given the proximity of that wire to the exhaust manifold and the fact that it was flopping around, I might look the wire over for a break or bare spot before procuring a new temp gauge and taking the time to install it.
__________________
'70 cab, '71 chassis, 383, TH350, NP205.
'71 Malibu convertible
'72 Malibu hard top
Center City, MN
mrein3 is offline   Reply With Quote
Old 12-06-2022, 03:06 PM   #8
HO455
Post Whore
 
HO455's Avatar
 
Join Date: Feb 2016
Location: Portland Oregon
Posts: 10,755
Re: Can temperature gauge be adjusted?

I had the same thing happen to me. I didn't get to concerned as these aren't calibrated gauges. They are a reference to what is normal and if there is a problem the guage will still indicate a higher or lower than normal temperature condition.

That being said you can remove the needle from the post and reposition it to where you would like it to read when cold.

But in the big cycle of nature, mine fell off a second time, about two years after the first time, and reset itself nearly back where it was originally. So you could give that a try too.
__________________
Thanks to Bob and Jeanie and everyone else at Superior Performance for all their great help.
RIP Bob Parks.
1967 Burban the WMB,1991 S(stink)-10 Blazer,1969 GTO, 1970 Javelin, 1952 F2 Ford 4X4, 29 Model A, 72 Firebird. 85 Alfa Romeo
If it breaks I didn't want it in the first place
The WMB repair thread http://67-72chevytrucks.com/vboard/s...d.php?t=698377
HO455 is online now   Reply With Quote
Old 01-15-2023, 06:08 PM   #9
Mruss70
Registered User
 
Join Date: Dec 2017
Location: Granbury, Texas
Posts: 6
Re: Can temperature gauge be adjusted?

On my gauge the needle came off and I couldn’t find it. My father in law had an extra so I put it in and the needle wouldn’t move off below cold. I traced the circuits and didn’t find any problems. I checked the temp sending unit and noted that the ohms were going down as the engine warmed up. 1700 ohms cold and 445 warm. After messing with it for a couple of days I was going to a guys house that works on these old trucks and the gauge started working. Now the gauge stays about 1/4 inch under half way. I did notice when I shut the truck off and restarted it the needle stays under the cold line until I rev the motor then it slowly climbs to 1/4 inch under half way.

Name:  21DB2050-0ACC-4664-85D6-74BBE4D06833.jpg
Views: 195
Size:  46.6 KB
__________________
Mike
68 Chevy c10 2” drop in front & 4” drop in rear

Last edited by Mruss70; 01-15-2023 at 06:16 PM. Reason: Image
Mruss70 is offline   Reply With Quote
Old 01-15-2023, 07:01 PM   #10
Accelo
Senior Member
 
Accelo's Avatar
 
Join Date: Mar 2015
Location: washington
Posts: 2,145
Re: Can temperature gauge be adjusted?

I have the specifications for the earlier sensors. I am not 100% sure it would apply but here goes.
@ 75 deg 700 ohms
@ 180 deg 140 ohms.

I mentioned, in an earlier post, you could correct a gauge by adding resistance. If you go this route it would only be correct when it was running at the temp the gauge was corrected for. It would be possible to overheat, and the gauge not read correctly,when the motor is overheating. It all depends on how much resistance one had to add to correct the gauge.

This is a bunch of monkeying around. Best to replace the broken gauge. Used ones are around and if time is money it would be the least inexpensive repair. However, I am not saying what your time is worth! "or do I need to replace the original gauge?" "Yes."

One could measure the ohms resistance and determine if the sensor is correct. a pot of water and a ohm meter is all that is required to confirm the sensor's function.
Good luck.
Accelo is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 02:19 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com