What did you do to your truck today? - Page 7 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

DWright · 11-07-2009, 05:25 PM

Just got done with hacking my '79 donor with the good 'ole red-wrench and tractor. Now i have ps, power disc brakes and a 350 w/ 62cc heads to go in front of my camaro T5. SLowly making progress...

scotts62 · 11-07-2009, 05:45 PM

Hey there ya go! A little progress goes a long way

Tx Firefighter · 11-07-2009, 09:29 PM

I got a used engine and trans for my quick build 63 farm truck.

monolith · 11-07-2009, 10:18 PM

Rattle canned the bed flat black and installed some new 2 ga battery cables on the 64 GMC- now I need a new carb.

**DPowers** · 11-08-2009, 01:23 PM

Yesterday I picked up a '64 GMC cab that is sitting- I mean literally just sitting on a '73-87 frame. Now to figure out what to do with this one....

Rich 5150 69 · 11-08-2009, 03:03 PM

http://i154.photobucket.com/albums/s...9/IMG_0273.jpg
Yesterday front wheel bearing pack , brake check, greased frontend, resealed old factory seal at lower seam on cowl just below vent, it started leaking a couple of years ago.

DWright · 11-08-2009, 03:56 PM

Quote:

Originally Posted by monolith

Rattle canned the bed flat black and installed some new 2 ga battery cables on the 64 GMC- now I need a new carb.

What carb do ya' need? For which motor?

monolith · 11-08-2009, 04:48 PM

Quote:

Originally Posted by DWright

What carb do ya' need? For which motor?

This is what's on there now:

1964 GMC 305 V6

Truthfully, I don't even know what brand or model it is as I'm pretty new to these trucks, Old Rochester maybe? This one's shooting fuel out from under the brown washer in the middle of the body where the arm comes up.

Can these be rebuilt expediently?

I've also read that folks are swapping out Holley 500's on these motors- any advice on the matter is appreciated.

DWright · 11-08-2009, 06:55 PM

I believe that is a stromberg ww carb and it looks like you have a busted accelerator pump seal. The part number for the rebuild kit is CK449 and it should run you about $50. They arent hard to rebuild but switching to a 500cfm 2bbl Holley would be a better choice as these carbs are very outdated; even in '64. Now would be the time to swap. But thats just my opinion. If you had an inline 6 i have a freshly rebuilt rochester laying around and was gonna offer it to you to get you going again, but thats not the case here.

sams60gmc · 11-08-2009, 08:17 PM

Picked up these yesterday.

quickchevy · 11-08-2009, 08:28 PM

Opened the garage door and looked at it.

joe231 · 11-08-2009, 08:45 PM

Quote:

Originally Posted by sams60gmc

Picked up these yesterday.

whatcha gonna do with those?

sams60gmc · 11-08-2009, 08:49 PM

Quote:

Originally Posted by joe231

whatcha gonna do with those?

I'm going to run one of them after I shorten my frame. And I'm selling one to a guy at work. I'm in the market for some 60's style fenders tho.

MXmaniac · 11-08-2009, 08:51 PM

I put some new lug nuts on the front, put the driver's side fender back on. Then I went for a joyride with my girlfriend and taught her how to drive three-on-the-tree.

jgh64pkup · 11-08-2009, 08:53 PM

put the hood on it

Hottrucks · 11-08-2009, 09:00 PM

use it to haul the smoker to a freinds house...ok so it weighs about 6 lbs but I did put a full bag of charcoal in the bed and had 14 lbs of dry rubbed ribs in a cookie sheet on the pass floor..........

alot better than what it has been doing...yea still on cord wood duty maybe another coulpe weeks of that most everyday then the old girl is going to get a fluid change before winter.....

Hey MX gotte love them Texas Girls...does she have an older sister or single Mom?? If they love old trucks then I love them too......

Scot_Douglas · 11-08-2009, 09:18 PM

Drove about 100 miles taking the long way and back from a buddy's house. He loaned me a cherry picker and an engine stand. Got lots of looks cruising alone in the 66 with those things out back.

Slow Build · 11-08-2009, 09:39 PM

I drove mine over to check out lownslw64's ride (his build thread http://67-72chevytrucks.com/vboard/s...d.php?t=367652 ). When my truck grows up it wants to be just like that. His frame and suspension are pretty much done and done nice. You can tell he's not rushing things and doing them right. We talked for awhile and it sounds like we have alot of common goals for our trucks. It's great to see someone making good strides toward his goals, mine are still in dream, or more accurately delusional state. It inspired me though. I hope I can help him out sometime and get more inspired.

Great guy too. Showed me everything on the truck and shared alot of knowledge. I can't believe this is his first build. I'm hoping to run into him at the Goodguy's Get Together in Pleasanton next weekend (Nov 14-15) and by that man a beer.

Vernski · 11-09-2009, 01:13 AM

I've also read that folks are swapping out Holley 500's on these motors- any advice on the matter is appreciated.[/QUOTE] Monolith Here is a web site that may answer your questions about the Hollys.

http://www.6066gmcguy.org/holley.htm

Hope that helps.---Vernski

19GMC63 · 11-09-2009, 01:21 AM

Cool thread Sam.
I didn't do much... replaced the heater wheel, OG one was making a racket. Wired in some courtesy lights with door jamb switches.
Might have a line on a posi 3.73 rear end... the 3.08 peg-leg and T5 is a bad combo.

sams60gmc · 11-09-2009, 01:28 AM

Quote:

Originally Posted by 19GMC63

Cool thread Sam.
.

Thank you

sams60gmc · 11-09-2009, 02:12 AM

Did this today. Also tagged my glove box.

Scot_Douglas · 11-09-2009, 09:20 AM

Quote:

Originally Posted by sams60gmc

Did this today. Also tagged my glove box.

Nice work!

jbgroby · 11-09-2009, 09:28 AM

Monolith,

The change is not hard, you already have the rare part - "The Dual Intake", with out that you're dead in the water.

You need a holley 500 CFM carb, or another brand of your likin' and adaptor plate and you might need to make a new accelator linkage due to the dog leg you'll need, but other than that you're good to good. See webshots pics below.

http://rides.webshots.com/album/560082574YsEssM

monolith · 11-09-2009, 09:46 AM

Thanks a million for the advice guys! This site is a goldmine of encouragement and knowledge.

I'll be ordering a Holley 500 today after work, went around to my FLAPS's yesterday- no luck finding one in stock, have to order it.

11-07-2009, 05:25 PM	#151
DWright Shlong Bed Club Join Date: Apr 2009 Location: Milford, VA Posts: 220	Re: What did you do to your truck today? Just got done with hacking my '79 donor with the good 'ole red-wrench and tractor. Now i have ps, power disc brakes and a 350 w/ 62cc heads to go in front of my camaro T5. SLowly making progress... Attached Images Last edited by DWright; 11-07-2009 at 05:32 PM.

11-07-2009, 05:45 PM	#152
scotts62 One day... Join Date: Apr 2008 Location: Tuttle, Ok Posts: 9,240	Re: What did you do to your truck today? Hey there ya go! A little progress goes a long way __________________ Scott 93 crew cab build Project 62

11-07-2009, 09:29 PM	#153
Tx Firefighter Watch out for your cornhole ! Join Date: Jun 2003 Location: Azle, Texas Posts: 14,162	Re: What did you do to your truck today? I got a used engine and trans for my quick build 63 farm truck. __________________ I'm on the Instagram- @Gearhead_Kevin

11-07-2009, 10:18 PM	#154
monolith Zero Albedo Join Date: Mar 2009 Location: San Gabriel, California Posts: 478	Re: What did you do to your truck today? Rattle canned the bed flat black and installed some new 2 ga battery cables on the 64 GMC- now I need a new carb. __________________ Baz "Deserve's got nothin' to do with it." 66 GMC 1500 wideside longbed 250 4spd "Project Rekker"http://67-72chevytrucks.com/vboard/s...d.php?t=467467 65 GMC 1Ton Panelhttp://67-72chevytrucks.com/vboard/s...32#post4794432 65 Chevy Panel (former U.S.Navy truck) 64 Chevy Suburban Carryall 4x4http://67-72chevytrucks.com/vboard/s...d.php?t=358348 64 GMC 1000 wideside longbed 305 4spdhttp://67-72chevytrucks.com/vboard/s....php?p=3600890(Rip- parts truck now) 68 Dodge Charger

11-08-2009, 01:23 PM	#155
DPowers One foot in front of the other Join Date: Aug 2008 Location: Parrottsville, TN Posts: 5,428	Re: What did you do to your truck today? Yesterday I picked up a '64 GMC cab that is sitting- I mean literally just sitting on a '73-87 frame. Now to figure out what to do with this one.... Last edited by DPowers; 11-08-2009 at 01:23 PM.

11-08-2009, 03:03 PM	#156
Rich 5150 69 Registered User Join Date: Nov 2009 Location: Galt, Calif Posts: 2,437	Re: What did you do to your truck today? http://i154.photobucket.com/albums/s...9/IMG_0273.jpg Yesterday front wheel bearing pack , brake check, greased frontend, resealed old factory seal at lower seam on cowl just below vent, it started leaking a couple of years ago.

11-08-2009, 06:55 PM	#159
DWright Shlong Bed Club Join Date: Apr 2009 Location: Milford, VA Posts: 220	Re: What did you do to your truck today? I believe that is a stromberg ww carb and it looks like you have a busted accelerator pump seal. The part number for the rebuild kit is CK449 and it should run you about $50. They arent hard to rebuild but switching to a 500cfm 2bbl Holley would be a better choice as these carbs are very outdated; even in '64. Now would be the time to swap. But thats just my opinion. If you had an inline 6 i have a freshly rebuilt rochester laying around and was gonna offer it to you to get you going again, but thats not the case here.

11-08-2009, 08:17 PM	#160
sams60gmc Registered User Join Date: Sep 2008 Location: Vancouver Washington Posts: 726	Re: What did you do to your truck today? Picked up these yesterday. Attached Images __________________ 1960 GMC short fleet, full frame build... http://67-72chevytrucks.com/vboard/s...d.php?t=329718

11-08-2009, 08:28 PM	#161
quickchevy Registered User Join Date: Apr 2008 Location: Augusta,Ga Posts: 119	Re: What did you do to your truck today? Opened the garage door and looked at it.

11-08-2009, 08:51 PM	#164
MXmaniac Registered User Join Date: Jan 2007 Location: Denton, Texas Posts: 356	Re: What did you do to your truck today? I put some new lug nuts on the front, put the driver's side fender back on. Then I went for a joyride with my girlfriend and taught her how to drive three-on-the-tree. Attached Images __________________ Andrew '69 C-20(292, 4-speed) Retired Daily Driver '64 C-10(250, 3-speed) Fixerupper '97 F*rd Mustang GT(4.6L, 5-speed) Daily Driver If I only wanted two pedals I'd have bought a bicycle.

11-08-2009, 08:53 PM	#165
jgh64pkup Sunburst C10!!! Join Date: Jan 2009 Location: Texas Posts: 2,560	Re: What did you do to your truck today? put the hood on it __________________ Gage 1967 C10 Shortbed Stepside

11-08-2009, 09:00 PM	#166
Hottrucks Redefining LowBudget Join Date: Mar 2009 Location: lebanon Cow Hampshire Posts: 4,538	Re: What did you do to your truck today? use it to haul the smoker to a freinds house...ok so it weighs about 6 lbs but I did put a full bag of charcoal in the bed and had 14 lbs of dry rubbed ribs in a cookie sheet on the pass floor.......... alot better than what it has been doing...yea still on cord wood duty maybe another coulpe weeks of that most everyday then the old girl is going to get a fluid change before winter..... Hey MX gotte love them Texas Girls...does she have an older sister or single Mom?? If they love old trucks then I love them too......

11-08-2009, 09:18 PM	#167
Scot_Douglas Fabrication OCD Join Date: Oct 2009 Location: Howell, MI Posts: 403	Re: What did you do to your truck today? Drove about 100 miles taking the long way and back from a buddy's house. He loaned me a cherry picker and an engine stand. Got lots of looks cruising alone in the 66 with those things out back. __________________ 1964 C10 - sold to chris1044 1966 C10 Build 'Fread

11-08-2009, 09:39 PM	#168
Slow Build Registered User Join Date: Sep 2009 Location: California Delta Posts: 2,163	Re: What did you do to your truck today? I drove mine over to check out lownslw64's ride (his build thread http://67-72chevytrucks.com/vboard/s...d.php?t=367652 ). When my truck grows up it wants to be just like that. His frame and suspension are pretty much done and done nice. You can tell he's not rushing things and doing them right. We talked for awhile and it sounds like we have alot of common goals for our trucks. It's great to see someone making good strides toward his goals, mine are still in dream, or more accurately delusional state. It inspired me though. I hope I can help him out sometime and get more inspired. Great guy too. Showed me everything on the truck and shared alot of knowledge. I can't believe this is his first build. I'm hoping to run into him at the Goodguy's Get Together in Pleasanton next weekend (Nov 14-15) and by that man a beer. __________________ Name: Rich Current Ride: 1964 C-10 Short Fleetside Daily Driver: 2005 GMC crew cab short fleetside /2001 Chevy Tahoe Past GM Trucks: 1959 GMC short stepside 1968 GMC short stepside-4x4 1973 Chevy short stepside 1989 Chevy short fleetside-reg cab 1993 Chevy short fleetside-Xcab 2002 Chevy short fleetside-Xcab Save the dinosaurs, use synthetic oil.

11-09-2009, 01:13 AM	#169
Vernski Registered User Join Date: May 2009 Location: Rathdrum, Idaho Posts: 1,135	Re: What did you do to your truck today? I've also read that folks are swapping out Holley 500's on these motors- any advice on the matter is appreciated.[/QUOTE] Monolith Here is a web site that may answer your questions about the Hollys. http://www.6066gmcguy.org/holley.htm Hope that helps.---Vernski Last edited by Vernski; 11-09-2009 at 01:29 AM.



Register or Log In To remove these advertisements.

11-09-2009, 01:21 AM	#170
19GMC63 Registered User Join Date: Nov 2006 Location: Nashville, TN Posts: 1,510	Re: What did you do to your truck today? Cool thread Sam. I didn't do much... replaced the heater wheel, OG one was making a racket. Wired in some courtesy lights with door jamb switches. Might have a line on a posi 3.73 rear end... the 3.08 peg-leg and T5 is a bad combo.

11-09-2009, 02:12 AM	#172
sams60gmc Registered User Join Date: Sep 2008 Location: Vancouver Washington Posts: 726	Re: What did you do to your truck today? Did this today. Also tagged my glove box. Attached Images __________________ 1960 GMC short fleet, full frame build... http://67-72chevytrucks.com/vboard/s...d.php?t=329718

11-09-2009, 09:28 AM	#174
jbgroby Registered User Join Date: Nov 2008 Location: Lacombe, LA Posts: 2,770	Re: What did you do to your truck today? Monolith, The change is not hard, you already have the rare part - "The Dual Intake", with out that you're dead in the water. You need a holley 500 CFM carb, or another brand of your likin' and adaptor plate and you might need to make a new accelator linkage due to the dog leg you'll need, but other than that you're good to good. See webshots pics below. http://rides.webshots.com/album/560082574YsEssM Attached Images __________________ http://s1299.photobucket.com/user/jb...23904108567829 Last edited by jbgroby; 11-09-2009 at 10:13 AM.

11-09-2009, 09:46 AM	#175
monolith Zero Albedo Join Date: Mar 2009 Location: San Gabriel, California Posts: 478	Re: What did you do to your truck today? Thanks a million for the advice guys! This site is a goldmine of encouragement and knowledge. I'll be ordering a Holley 500 today after work, went around to my FLAPS's yesterday- no luck finding one in stock, have to order it. __________________ Baz "Deserve's got nothin' to do with it." 66 GMC 1500 wideside longbed 250 4spd "Project Rekker"http://67-72chevytrucks.com/vboard/s...d.php?t=467467 65 GMC 1Ton Panelhttp://67-72chevytrucks.com/vboard/s...32#post4794432 65 Chevy Panel (former U.S.Navy truck) 64 Chevy Suburban Carryall 4x4http://67-72chevytrucks.com/vboard/s...d.php?t=358348 64 GMC 1000 wideside longbed 305 4spdhttp://67-72chevytrucks.com/vboard/s....php?p=3600890(Rip- parts truck now) 68 Dodge Charger

Register or Log In To remove these advertisements.