The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > Welcome and Discussion > General Discussion

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 08-04-2022, 05:46 PM   #1
kglowacky
Registered User
 
Join Date: Mar 2020
Location: The Woodlands,Tx
Posts: 555
emblem challange

going to test everyone's knowledge on Chevy/Bowtie name plates. I am looking for any year / type logo emblem to replace the round Cadilac emblem on my LS1 engine cover. It is 3 3/38 in dia. Really open to any thing that would fit in this circle that says chey or c-10 or Silverado. Going to remove Cadilac emblem paint the cover and hopefully find something to glue in the empty circle. Below is a picture of the exact cover I am going to use.

Name:  20220804_161607.jpg
Views: 338
Size:  21.1 KB
kglowacky is offline   Reply With Quote
Old 08-04-2022, 05:54 PM   #2
Keith Seymore
Registered User
 
Keith Seymore's Avatar
 
Join Date: May 2009
Location: Motor City
Posts: 9,135
Re: emblem challange

Quote:
Originally Posted by kglowacky View Post
going to test everyone's knowledge on Chevy/Bowtie name plates. I am looking for any year / type logo emblem to replace the round Cadilac emblem on my LS1 engine cover. It is 3 3/38 in dia. Really open to any thing that would fit in this circle that says chey or c-10 or Silverado. Going to remove Cadilac emblem paint the cover and hopefully find something to glue in the empty circle. Below is a picture of the exact cover I am going to use.

Attachment 2209417
Looks like the bowtie from a rally wheel centercap might be a good fit.

Check 2wd (smaller) and 4wd (larger) for fit.

K
__________________
Chevrolet Flint Assembly
1979-1986
GM Full Size Truck Engineering
1986 - 2019
Intro from an Old Assembly Guy: http://67-72chevytrucks.com/vboard/s...d.php?t=342926
My Pontiac story: http://forums.maxperformanceinc.com/...d.php?t=560524
Chevelle intro: http://www.superchevy.com/features/s...hevy-chevelle/
Keith Seymore is offline   Reply With Quote
Old 08-04-2022, 06:32 PM   #3
cwcarpenter98
Senior Member


 
cwcarpenter98's Avatar
 
Join Date: Jan 2018
Location: Hickory Flat, GA
Posts: 4,419
Re: emblem challange

Quote:
Originally Posted by Keith Seymore View Post
Looks like the bowtie from a rally wheel centercap might be a good fit.

Check 2wd (smaller) and 4wd (larger) for fit.

K
I was thinking the same thing
__________________
Christian Carpenter

1963 C10 - Frankentruck 283, 3 speed with overdrive
Overdrive wiring here
1963-ish truck bed trailer - Half-Wit

1981 C10 - Penny 305, th350

1995 Dodge Dakota Sport

"I'll put it simple: if you're going hard enough left, you'll find yourself turning right." - Doc Hudson
cwcarpenter98 is offline   Reply With Quote
Old 08-04-2022, 09:32 PM   #4
mongocanfly
Post Whore

 
mongocanfly's Avatar
 
Join Date: May 2015
Location: Alabama
Posts: 14,557
Re: emblem challange

or just get any other LS engine cover..thats what i did..my LS engine came from a Caddy, i just swapped out the cover for a standard truck engine cover
but i think Keiths on to something
__________________
Mongo...aka Greg

RIP Dad
RIP Jesse

1981 C30 LQ9 NV4500..http://67-72chevytrucks.com/vboard/s...d.php?t=753598
Mongos AD- LS3 TR6060...http://67-72chevytrucks.com/vboard/s...34#post8522334
Columbus..the 1957 IH 4x4...http://67-72chevytrucks.com/vboard/s...63#post8082563
2023 Chevy Z71..daily driver
mongocanfly is offline   Reply With Quote
Old 08-04-2022, 10:37 PM   #5
kglowacky
Registered User
 
Join Date: Mar 2020
Location: The Woodlands,Tx
Posts: 555
Re: emblem challange

Looks like Keith is the winner. Does anyone have a part number for the largest one so I can find one. Thanks

Last edited by kglowacky; 08-07-2022 at 08:32 PM.
kglowacky is offline   Reply With Quote
Old 09-27-2022, 05:51 PM   #6
kglowacky
Registered User
 
Join Date: Mar 2020
Location: The Woodlands,Tx
Posts: 555
Re: emblem challange

Here's what I found. After a lot of hunting, I found A aftermarket oil breather unit that I bought cut off the top and got me an emblem. Here are the results. Thanks everyone
Attached Images
   
kglowacky is offline   Reply With Quote
Old 09-27-2022, 08:41 PM   #7
4u2nv
Registered User
 
Join Date: Oct 2018
Location: Ontario Peterborough
Posts: 732
Re: emblem challange

There's an idea that came out right , nice work looks awesome
4u2nv is offline   Reply With Quote
Old 09-28-2022, 09:39 PM   #8
yuccales
Registered User
 
yuccales's Avatar
 
Join Date: May 2011
Location: Northern Calif.
Posts: 3,559
Re: emblem challange

Just in case you want a change, these are 3 3/8" od.
Attached Images
 
yuccales is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 04:19 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com