LS1 into a 73 cheyenne - Page 3 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

78-5.3 · 12-11-2009, 09:29 AM

Quote:

Originally Posted by smokedat

has anyone used rubber type if so how is it holding up?

sample pic

i used factory tahoe fule lines in my truck im amazed it not used as much??
i got them from a wreck 2001 tahoe your engine being from a camaro? why not look a the fuel lines from that?? i did some slight rebending but it followed down the back of the engine on the transmission across to the chassis rair down to the tank where i modified it to suit my 78 job done im sure the camaro lines have a similar setup

JohnC · 12-11-2009, 10:22 AM

This seems to be an awesome build. Definitely subscribing!

That willwood set up looks pretty sweet on there.

mcbassin · 12-15-2009, 09:09 AM

Quote:

Originally Posted by 78-5.3

i used factory tahoe fule lines in my truck im amazed it not used as much??
i got them from a wreck 2001 tahoe your engine being from a camaro? why not look a the fuel lines from that?? i did some slight rebending but it followed down the back of the engine on the transmission across to the chassis rair down to the tank where i modified it to suit my 78 job done im sure the camaro lines have a similar setup

This is a good idea if you can make them work in your truck.

LMDGUY · 01-14-2010, 02:25 PM

Quote:

Originally Posted by smokedat

has anyone used rubber type if so how is it holding up?

sample pic

I used rubber efi fuel line (with high presure clamps) on 5.0 swaps in mustangs and it holds up great. One of my builds is at about 7 years old with no issues.

smokedat · 01-15-2010, 12:59 AM

Quote:

Originally Posted by LMDGUY

I used rubber efi fuel line (with high presure clamps) on 5.0 swaps in mustangs and it holds up great. One of my builds is at about 7 years old with no issues.

Thanks for the input, will consider this option.

menace121978 · 12-10-2009, 08:33 PM

ive heard they hold great when used with the right high psi hose clamps. not those pictured

the screw type.

Thealien · 12-10-2009, 09:55 PM

I recently bought the mastercool hydraulic flaring tool. It is "THE" flaring tool! The only flare die it doesn't have is the 37 degree and I "may" add it. I bought it just for the GM pushloc flare, everything else is a bonus. Anyone can make a good flare with that tool! It can be found for just under $300 if you look.

smokedat · 12-11-2009, 01:04 AM

clinebarger

so i did some research on the net, and i think im finding that the 799 was a pre production ls6 head, and the 243 replaced them, but im also seeing some 06 corvettes with the 799 heads as well??

Casting number 799 is also an LS2 head. Came on some late 06 and up tbss and other LS2 vehicles. These are the mexico cast heads. Little rougher finish. Same basic head and flow though.

smokedat · 12-11-2009, 01:06 AM

Thealien

Thanks for the recomendation will look into getting one.

smokedat · 12-11-2009, 01:25 AM

Wilwood tandem chamber master cylinder 1 1/8 bore

3r!c84 · 12-11-2009, 07:40 AM

how much was that little guy?

smokedat · 12-11-2009, 01:33 PM

3r!c84

The little guy was $240 in the polish $200 for the natural finish

smokedat · 12-12-2009, 02:39 PM

..

rongstad · 12-12-2009, 07:36 PM

x2............change to high pressure hose and plastic to stainless clamps

smokedat · 12-13-2009, 02:24 PM

thanks for the input will upgrade the clamps

smokedat · 12-15-2009, 03:12 AM

new bumper

smokedat · 12-15-2009, 03:18 AM

nade shifter

HevyChevy42 · 02-06-2012, 10:32 PM

Quote:

Originally Posted by smokedat

nade shifter

Where did you find that nade shift knobe...sweet man

smokedat · 02-06-2012, 10:42 PM

That was a real nade that had been drilled out and had the powder removed, it had some weight on it, i got it at the swap meet sum dude that was selling military novelties

Quote:

Originally Posted by HevyChevy42

Where did you find that nade shift knobe...sweet man

The_BullDog · 02-09-2012, 01:49 PM

WOW finally tracked down your build tread and I am blown away! All I can say is SICK!

menace121978 · 12-15-2009, 09:32 AM

looking good man! you arent messing around!

btw, what mount plates are you going with for the LSx?

smokedat · 12-15-2009, 02:46 PM

btw, what mount plates are you going with for the LSx?[/QUOTE]

the motor mount plates are from S&P, allows you to bolt LS-1 to original V-8 motor mounts

mcbassin · 12-15-2009, 05:23 PM

Looking Good!

JohnC · 12-15-2009, 06:53 PM

Sweet!

78-5.3 · 12-16-2009, 09:30 PM

Quote:

Originally Posted by smokedat

btw, what mount plates are you going with for the LSx?

the motor mount plates are from S&P, allows you to bolt LS-1 to original V-8 motor mounts[/QUOTE]

ls1 & vortec 4.8 -5.3-6.0

12-11-2009, 10:22 AM	#2
JohnC Registered User Join Date: Feb 2009 Location: Oklahoma Posts: 7,461	Re: LS1 into a 73 cheyenne This seems to be an awesome build. Definitely subscribing! That willwood set up looks pretty sweet on there.

12-10-2009, 08:33 PM	#6
menace121978 Registered User Join Date: Jan 2009 Location: orangevale, ca Posts: 3,626	Re: LS1 into a 73 cheyenne ive heard they hold great when used with the right high psi hose clamps. not those pictured the screw type. __________________ "Dennis the Menace" 1978 Silverado (2wd, 1/2 ton, short bed)complete nut & bolt frame off restomod LQ9/4L80E MY LS SWAP/FRAME OFF BUILD BOOK 2006 TBSS way too much to list

12-10-2009, 09:55 PM	#7
Thealien Senior Member Join Date: Jun 2007 Location: Pine Ridge Florida Posts: 4,120	Re: LS1 into a 73 cheyenne I recently bought the mastercool hydraulic flaring tool. It is "THE" flaring tool! The only flare die it doesn't have is the 37 degree and I "may" add it. I bought it just for the GM pushloc flare, everything else is a bonus. Anyone can make a good flare with that tool! It can be found for just under $300 if you look.

12-11-2009, 01:04 AM	#8
smokedat Registered User Join Date: Nov 2009 Location: santa paula Ca Posts: 772	Re: LS1 into a 73 cheyenne clinebarger so i did some research on the net, and i think im finding that the 799 was a pre production ls6 head, and the 243 replaced them, but im also seeing some 06 corvettes with the 799 heads as well?? Casting number 799 is also an LS2 head. Came on some late 06 and up tbss and other LS2 vehicles. These are the mexico cast heads. Little rougher finish. Same basic head and flow though.

12-11-2009, 01:06 AM	#9
smokedat Registered User Join Date: Nov 2009 Location: santa paula Ca Posts: 772	Re: LS1 into a 73 cheyenne Thealien Thanks for the recomendation will look into getting one.

12-11-2009, 01:25 AM	#10
smokedat Registered User Join Date: Nov 2009 Location: santa paula Ca Posts: 772	Re: LS1 into a 73 cheyenne Wilwood tandem chamber master cylinder 1 1/8 bore Attached Images

12-11-2009, 07:40 AM	#11
3r!c84 Badass Join Date: Jan 2009 Location: lox. fl Posts: 4,586	Re: LS1 into a 73 cheyenne how much was that little guy? __________________ Think outside the box? -84c10 (1stcar)→My Build← -00 Saturn 5spd drop a gear and disappear! 1/4:13:90

12-11-2009, 01:33 PM	#12
smokedat Registered User Join Date: Nov 2009 Location: santa paula Ca Posts: 772	Re: LS1 into a 73 cheyenne 3r!c84 The little guy was $240 in the polish $200 for the natural finish

12-12-2009, 02:39 PM	#13
smokedat Registered User Join Date: Nov 2009 Location: santa paula Ca Posts: 772	Re: LS1 into a 73 cheyenne .. Last edited by smokedat; 12-13-2009 at 02:17 PM.

12-12-2009, 07:36 PM	#14
rongstad Future: 86 on GenIV power! Join Date: Jun 2009 Location: San Antonio, Texas Posts: 105	Re: LS1 into a 73 cheyenne x2............change to high pressure hose and plastic to stainless clamps

12-13-2009, 02:24 PM	#15
smokedat Registered User Join Date: Nov 2009 Location: santa paula Ca Posts: 772	Re: LS1 into a 73 cheyenne thanks for the input will upgrade the clamps

12-15-2009, 03:12 AM	#16
smokedat Registered User Join Date: Nov 2009 Location: santa paula Ca Posts: 772	Re: LS1 into a 73 cheyenne new bumper Attached Images

12-15-2009, 03:18 AM	#17
smokedat Registered User Join Date: Nov 2009 Location: santa paula Ca Posts: 772	Re: LS1 into a 73 cheyenne nade shifter Attached Images Last edited by smokedat; 12-15-2009 at 03:27 AM.

02-09-2012, 01:49 PM	#20
The_BullDog Registered User Join Date: May 2010 Location: Orange Park Florida Posts: 204	Re: LS1 into a 73 cheyenne WOW finally tracked down your build tread and I am blown away! All I can say is SICK!

12-15-2009, 09:32 AM	#21
menace121978 Registered User Join Date: Jan 2009 Location: orangevale, ca Posts: 3,626	Re: LS1 into a 73 cheyenne looking good man! you arent messing around! btw, what mount plates are you going with for the LSx? __________________ "Dennis the Menace" 1978 Silverado (2wd, 1/2 ton, short bed)complete nut & bolt frame off restomod LQ9/4L80E MY LS SWAP/FRAME OFF BUILD BOOK 2006 TBSS way too much to list



Register or Log In To remove these advertisements.

12-15-2009, 02:46 PM	#22
smokedat Registered User Join Date: Nov 2009 Location: santa paula Ca Posts: 772	Re: LS1 into a 73 cheyenne btw, what mount plates are you going with for the LSx?[/QUOTE] the motor mount plates are from S&P, allows you to bolt LS-1 to original V-8 motor mounts Attached Images

12-15-2009, 05:23 PM	#23
mcbassin Still Learning Join Date: Jul 2009 Location: Central Oklahoma Posts: 10,108	Re: LS1 into a 73 cheyenne Looking Good! __________________ Mike "69 Short Wide" My Project 86 Silverado Landen's Project Instagram: @mcbassin My Website C/10 Club Oklahoma Facebook Group

12-15-2009, 06:53 PM	#24
JohnC Registered User Join Date: Feb 2009 Location: Oklahoma Posts: 7,461	Re: LS1 into a 73 cheyenne Sweet!

Register or Log In To remove these advertisements.