The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1973 - 1987 Chevrolet & GMC Squarebody Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 07-23-2021, 02:05 AM   #1
79vette
Registered User
 
Join Date: Jan 2017
Location: Sandy, UT
Posts: 190
Military Blazer Build

Over the next couple months I'll hopefully be finishing up building my M1009 Blazer. I'm going to post up all the pics I have from the build up to this point, and document the remainder of the project as I go.

The truck was a factory 6.2 diesel backed by a TH400 and NP208, with 10 bolt axles and 3.08 gears. When I bought it from the national guard it was on 33" Goodyear MTRs.

Today it has a 2 speed aux trans (Advanced Adapters "Ranger"), SM465 and NP205. Axles are 10/12bolt with 3.73 gears and ARB lockers in both ends. Still on 33" MTRs and still has the 6.2 diesel.


The first project was the floor replacement. I bought it with bad floor pan rust, like to the point the seats were about to drop out onto the road and I would not allow a passenger to ride in the truck.

Here's some photos of the carnage. 3 of the 4 bolt locations on the passenger side were cracked through, and there was >2" of vertical motion of the seat every time the truck hit a bump.

Name:  IMG_20200125_115809.jpg
Views: 522
Size:  59.9 KB

Name:  IMG_20200125_115833.jpg
Views: 519
Size:  47.4 KB

Name:  IMG_20200125_115839.jpg
Views: 525
Size:  49.8 KB

Name:  IMG_20200125_151147.jpg
Views: 521
Size:  68.1 KB
__________________
1988 "Crane Truck" C30 - 350, SM465, with a 15' knuckle crane - thread
1986 M1009 - 6.2 Diesel, SM465, 2 speed aux trans, NP205 - thread
1979 Corvette - 350 T5
1977 Jimmy - 350, TH400, NP203
1982 Blazer - 350, 700R4, NP208 - Totalled, now a parts truck
Scratch built 16' flatbed trailer - thread

Last edited by 79vette; 07-23-2021 at 02:41 AM.
79vette is offline   Reply With Quote
Old 07-23-2021, 02:12 AM   #2
79vette
Registered User
 
Join Date: Jan 2017
Location: Sandy, UT
Posts: 190
Re: Military Blazer Build

First step was to torch out the rotten metal and make a carboard template, and then transfer that to new 16ga steel. As you can see the rockers are pretty bad and I should have done them at the same time, but this was my only daily driver and I needed it back on the road ASAP. Rocker replacement will be a later post...

Name:  IMG_20200125_151207.jpg
Views: 509
Size:  57.8 KB

Name:  IMG_20200125_132556.jpg
Views: 507
Size:  46.5 KB

Name:  IMG_20200125_163002.jpg
Views: 507
Size:  40.5 KB


There's an annoying upward bend in the frame which I had to box around, since I was working with flat sheet. After fixing that it fit up, and it was easy to drill and plug weld into place.

Name:  IMG_20200126_141151.jpg
Views: 549
Size:  46.0 KB


Then cut the hole for the 24v panel wiring (the military had a power distribution point near the rear bench seat for radios and other gear) and made a couple patch sections for the rear cargo area. Ignore the lousy welding here

Name:  IMG_20200126_170611.jpg
Views: 502
Size:  45.4 KB
__________________
1988 "Crane Truck" C30 - 350, SM465, with a 15' knuckle crane - thread
1986 M1009 - 6.2 Diesel, SM465, 2 speed aux trans, NP205 - thread
1979 Corvette - 350 T5
1977 Jimmy - 350, TH400, NP203
1982 Blazer - 350, 700R4, NP208 - Totalled, now a parts truck
Scratch built 16' flatbed trailer - thread

Last edited by 79vette; 07-23-2021 at 02:44 AM.
79vette is offline   Reply With Quote
Old 07-23-2021, 02:29 AM   #3
79vette
Registered User
 
Join Date: Jan 2017
Location: Sandy, UT
Posts: 190
Re: Military Blazer Build

I wasn't able to reproduce the stamped ribs in the replacement floor, so instaead I used a 1"x3"x.060" rectangle tube cut in half to make a 0.5"x3" C channel, and welded that to the floor as a stiffening rib. This spans from the front floor support to the rear floor support and provides a load path from the seats into the underlying cab structure, so the flat sheet metal floor isn't supporting the weight of the seats.

I dont have photos, but there is a piece of thick wall pipe welded between the C channel support and the floor sheet metal to allow the seat bolts to clamp up on a solid piece instead of crushing the channel.

Name:  IMG_20200201_164014.jpg
Views: 503
Size:  49.5 KB


Repeat process on the other side.

Name:  IMG_20200201_205756.jpg
Views: 506
Size:  82.3 KB

Name:  IMG_20200202_185141.jpg
Views: 504
Size:  90.9 KB


At this point I took a quick break to go pick up some new toys. Still no center section built to connect the 2 sides of the floor and the transmission tunnel cover was installed installed with one bolt, so I almost lost the turbo on the interstate...

Name:  IMG_20200208_173333.jpg
Views: 503
Size:  80.8 KB


After picking up the turbo, I raised and extended the tunnel cover to accommodate the SM465 and auxiliary trans.

Name:  IMG_20200209_161057.jpg
Views: 508
Size:  47.1 KB
__________________
1988 "Crane Truck" C30 - 350, SM465, with a 15' knuckle crane - thread
1986 M1009 - 6.2 Diesel, SM465, 2 speed aux trans, NP205 - thread
1979 Corvette - 350 T5
1977 Jimmy - 350, TH400, NP203
1982 Blazer - 350, 700R4, NP208 - Totalled, now a parts truck
Scratch built 16' flatbed trailer - thread

Last edited by 79vette; 07-23-2021 at 02:46 AM.
79vette is offline   Reply With Quote
Old 07-23-2021, 02:34 AM   #4
79vette
Registered User
 
Join Date: Jan 2017
Location: Sandy, UT
Posts: 190
Re: Military Blazer Build

Built a raised section to clear the driveshaft and connect the 2 sides of the floor, made a couple more patches for the extra rusty spots, welded everything solid, and sprayed primer

Name:  IMG_20200210_143326.jpg
Views: 500
Size:  73.1 KB

Name:  IMG_20200216_164212.jpg
Views: 498
Size:  86.2 KB

Name:  IMG_20200216_164209.jpg
Views: 499
Size:  62.5 KB

Name:  IMG_20200210_191824.jpg
Views: 499
Size:  51.8 KB

Name:  IMG_20200216_204719.jpg
Views: 486
Size:  83.4 KB
__________________
1988 "Crane Truck" C30 - 350, SM465, with a 15' knuckle crane - thread
1986 M1009 - 6.2 Diesel, SM465, 2 speed aux trans, NP205 - thread
1979 Corvette - 350 T5
1977 Jimmy - 350, TH400, NP203
1982 Blazer - 350, 700R4, NP208 - Totalled, now a parts truck
Scratch built 16' flatbed trailer - thread
79vette is offline   Reply With Quote
Old 07-23-2021, 02:40 AM   #5
79vette
Registered User
 
Join Date: Jan 2017
Location: Sandy, UT
Posts: 190
Re: Military Blazer Build

Applied Peel-n-Seal from Lowes to the floors to help reduce vibration and echos, cut out some rubber floor mats, reinstalled the interior (and rifle rack!), and its like a whole new truck. At least I dont have to wear safety glasses to keep road gravel out of my eyes when I drive now...

Name:  IMG_20200315_131041.jpg
Views: 500
Size:  53.1 KB

Name:  IMG_20200406_192129.jpg
Views: 496
Size:  32.8 KB

Name:  IMG_20200222_232312.jpg
Views: 496
Size:  77.8 KB

Name:  IMG_20200229_224713.jpg
Views: 499
Size:  68.6 KB
__________________
1988 "Crane Truck" C30 - 350, SM465, with a 15' knuckle crane - thread
1986 M1009 - 6.2 Diesel, SM465, 2 speed aux trans, NP205 - thread
1979 Corvette - 350 T5
1977 Jimmy - 350, TH400, NP203
1982 Blazer - 350, 700R4, NP208 - Totalled, now a parts truck
Scratch built 16' flatbed trailer - thread
79vette is offline   Reply With Quote
Old 07-23-2021, 08:35 AM   #6
Corts60
Just here to tinker
 
Corts60's Avatar
 
Join Date: Jun 2008
Location: Holland, MI
Posts: 3,672
Re: Military Blazer Build

That thing is going to be rugged! Very nice.
Corts60 is offline   Reply With Quote
Old 07-25-2021, 10:55 PM   #7
84 400
Sb 400 club
 
84 400's Avatar
 
Join Date: Nov 2005
Location: NH / MA
Posts: 2,741
Re: Military Blazer Build

Would love to know more about the ranger. Have one ready to go in ny 77 (has a 6.2 from a 1028 and sm465) but the tunnel and drive shaft mods are slowibg me down
__________________
1984 chevy c10, built 400sb,.(SOLD)
77 K10 Project / daily driver "The Grinch" http://67-72chevytrucks.com/vboard/s...d.php?t=318363
1956 Willys Wagon (327 chevy) Project (Now Buick 225)
1980 Corvette L-48 4 speed
1992 Mustang GT built 5.0 5 speed

1985 C10 LWB Sold
1982 K10 SWB plow truck Parted out
1986 D30 M1028 fire brush truck Parted out
84 400 is offline   Reply With Quote
Old 07-25-2021, 11:39 PM   #8
79vette
Registered User
 
Join Date: Jan 2017
Location: Sandy, UT
Posts: 190
Re: Military Blazer Build

Quote:
Originally Posted by 84 400 View Post
Would love to know more about the ranger. Have one ready to go in ny 77 (has a 6.2 from a 1028 and sm465) but the tunnel and drive shaft mods are slowibg me down
I'm quite happy with mine, and happy to answer any questions. What would you like to know?

You gotta cut a hole in the tunnel for the new shifter and offset all the driveshafts ~7" back (longer front, shorter rear). I did a bunch of tunnel work to raise the transfer case up a couple inches for better clearance, but I probably wouldn't have bothered if I hadn't cut the entire floor out already.

Advanced Adapters recently discontinued them and I'm looking for another. If for whatever reason you decide to not install yours I'd be happy to buy it off you
__________________
1988 "Crane Truck" C30 - 350, SM465, with a 15' knuckle crane - thread
1986 M1009 - 6.2 Diesel, SM465, 2 speed aux trans, NP205 - thread
1979 Corvette - 350 T5
1977 Jimmy - 350, TH400, NP203
1982 Blazer - 350, 700R4, NP208 - Totalled, now a parts truck
Scratch built 16' flatbed trailer - thread
79vette is offline   Reply With Quote
Old 07-31-2021, 09:33 PM   #9
79vette
Registered User
 
Join Date: Jan 2017
Location: Sandy, UT
Posts: 190
Re: Military Blazer Build

Here's a few pics from my center console build. Everything was done with a grinder, because I didnt have a plasma at this point.

Name:  IMG_20200330_213916.jpg
Views: 322
Size:  81.2 KB

Name:  IMG_20200330_213944.jpg
Views: 328
Size:  44.5 KB

Water bottle holder was sized to fit a 1L Nalgene, which is my favorite water bottle of all time.
Name:  IMG_20200424_163000_1.jpg
Views: 328
Size:  74.2 KB
__________________
1988 "Crane Truck" C30 - 350, SM465, with a 15' knuckle crane - thread
1986 M1009 - 6.2 Diesel, SM465, 2 speed aux trans, NP205 - thread
1979 Corvette - 350 T5
1977 Jimmy - 350, TH400, NP203
1982 Blazer - 350, 700R4, NP208 - Totalled, now a parts truck
Scratch built 16' flatbed trailer - thread
79vette is offline   Reply With Quote
Old 07-31-2021, 09:40 PM   #10
79vette
Registered User
 
Join Date: Jan 2017
Location: Sandy, UT
Posts: 190
Re: Military Blazer Build

The switches and switch guards are stainless look-alikes for the titanium hardware made by Rockwell for the Space Shuttle switch panels. A bit silly perhaps, but its the looks i was going for.

Name:  IMG_20200502_144643.jpg
Views: 327
Size:  45.1 KB

I also installed an intercom from a general aviation aircraft so I can run headsets on the highway. The military considered sound insulation to be optional equipment, and the diesel motor is too loud to yell over at freeway speeds
Name:  IMG_20200502_001717.jpg
Views: 320
Size:  40.7 KB

Installed USB charging for all the latest gadgets and gizmos
Name:  IMG_20200503_162124.jpg
Views: 316
Size:  43.7 KB

Headphone and mic jacks for the headsets
Name:  IMG_20200516_172058.jpg
Views: 321
Size:  31.2 KB


Box all assembled and mocked up. Ready for exterior paint and final wiring
Name:  IMG_20200516_172054.jpg
Views: 328
Size:  47.3 KB
__________________
1988 "Crane Truck" C30 - 350, SM465, with a 15' knuckle crane - thread
1986 M1009 - 6.2 Diesel, SM465, 2 speed aux trans, NP205 - thread
1979 Corvette - 350 T5
1977 Jimmy - 350, TH400, NP203
1982 Blazer - 350, 700R4, NP208 - Totalled, now a parts truck
Scratch built 16' flatbed trailer - thread
79vette is offline   Reply With Quote
Old 07-31-2021, 09:47 PM   #11
79vette
Registered User
 
Join Date: Jan 2017
Location: Sandy, UT
Posts: 190
Re: Military Blazer Build

I sprayed paint on the box, and left a masked off strip at the bottom. The plan is to wire everything from the bottom, and then weld in the bottom panel and touch up the paint at the end.
Name:  IMG_20200517_144821.jpg
Views: 317
Size:  49.1 KB

Here's some pics from wiring day. I made a spreadsheet showing all the needed connections and copied it to my tablet, grabbed some cold beverages and the soldering iron, and went to work.
Name:  IMG_20200516_231635.jpg
Views: 322
Size:  61.7 KB

Made up a pigtail harness for the intercom box
Name:  IMG_20200517_135357.jpg
Views: 322
Size:  50.4 KB

Here's everything wired up. Intercom, headset jacks, seat heaters, switches, USB chargers, and LED lights for inside the box.
Name:  IMG_20200517_193854.jpg
Views: 322
Size:  37.8 KB

This milspec D38999 connector allows the box and all components to be removed from the truck. There's 37 circuits that connect to various hardware outside the box, and this connector packages everything in a compact and waterproof plug.
Name:  IMG_20200526_213825.jpg
Views: 324
Size:  34.8 KB
__________________
1988 "Crane Truck" C30 - 350, SM465, with a 15' knuckle crane - thread
1986 M1009 - 6.2 Diesel, SM465, 2 speed aux trans, NP205 - thread
1979 Corvette - 350 T5
1977 Jimmy - 350, TH400, NP203
1982 Blazer - 350, 700R4, NP208 - Totalled, now a parts truck
Scratch built 16' flatbed trailer - thread

Last edited by 79vette; 07-31-2021 at 09:54 PM.
79vette is offline   Reply With Quote
Old 07-31-2021, 09:52 PM   #12
79vette
Registered User
 
Join Date: Jan 2017
Location: Sandy, UT
Posts: 190
Re: Military Blazer Build

Got all the wiring finished, and made up the harness for the truck side
Name:  IMG_20200604_221915.jpg
Views: 316
Size:  57.7 KB

Made up some magnetic covers for the exposed wiring on the headset jacks and intercom box, welded in the bottom of the console and sprayed paint
Name:  IMG_20200605_194601.jpg
Views: 308
Size:  65.2 KB

Name:  IMG_20200605_214617.jpg
Views: 311
Size:  48.4 KB

Here it is installed into the truck
Name:  IMG_20200606_152759.jpg
Views: 310
Size:  50.6 KB

Name:  IMG_20200713_085508.jpg
Views: 317
Size:  43.6 KB
__________________
1988 "Crane Truck" C30 - 350, SM465, with a 15' knuckle crane - thread
1986 M1009 - 6.2 Diesel, SM465, 2 speed aux trans, NP205 - thread
1979 Corvette - 350 T5
1977 Jimmy - 350, TH400, NP203
1982 Blazer - 350, 700R4, NP208 - Totalled, now a parts truck
Scratch built 16' flatbed trailer - thread
79vette is offline   Reply With Quote
Old 08-01-2021, 03:18 PM   #13
Corts60
Just here to tinker
 
Corts60's Avatar
 
Join Date: Jun 2008
Location: Holland, MI
Posts: 3,672
Re: Military Blazer Build

Man that is some nice work. A man after my own heart with the wiring details. Well done!
Corts60 is offline   Reply With Quote
Old 08-06-2021, 03:15 AM   #14
mikelom
Registered User
 
Join Date: Mar 2018
Location: GA
Posts: 104
Re: Military Blazer Build

Awesome work! The center console looks nice and very functional.
mikelom is offline   Reply With Quote
Old 08-06-2021, 10:55 AM   #15
Pontiac1976
Registered User
 
Pontiac1976's Avatar
 
Join Date: Oct 2015
Location: Ottawa, Ontario, Canada
Posts: 750
Re: Military Blazer Build


Very nice work but the only thing that might give you trouble. Is if you ever need to replace the body mounts on the frame to body,( If the spot welds that are on the center floor patch are on the frame in this pic ) But very nice work on the consol. Keep up the good work.
__________________
1977 REG cab Long Bed with a 1984 Front Clip, 82 305 .60 over 9.0.1 flat top pistons, 4bbl, TH350, w/84 SS-intake & cam , w/ 1977 big block rad, 1975 gear box, 1984 master w/ metric fittings top & SAE fitting @ portion block, 1975 3.42 gear open diff. Duel 77-87 Factory air cleaner, duel inlet from rad support . Down sized 9' to new 8' Steel flat bed
Was a 77 454 w/308 gear. Taken out 550 lbs. up front with motor clip change.
Pontiac1976 is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 05:08 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com