Post pics of trucks w/fender mount spare tire carriers

[1963c-10]

Originally Posted by J.Cagle

63c-10, what size tires are you running, and is your truck lowered?

im running a 235/75r15 on stock 6 lug steelies. im doing a disc conversion on the front end and will run the same tire on a 74 k10 factory steelie that will except my factory hubcaps-
Posted via Mobile Device

[1963c-10]

factory height and factory shocks/springs on my 63
Posted via Mobile Device

[bgbchevy]

TTT...anybody have some more pictures?
Posted via Mobile Device

[lasher78]

heres mine...
Posted via Mobile Device

[1963c-10]

Thanks for sharing the pics lasher78....great looking truck. Looks like the rear tire has a flat spot huh?

[lasher78]

Originally Posted by 1963c-10

Thanks for sharing the pics lasher78....great looking truck. Looks like the rear tire has a flat spot huh?

yea you could say that....guess that is what happens after sitting over 10yrs flat...
Posted via Mobile Device
Posted via Mobile Device

[1963c-10]

yeah, 10 years will do that. Great looking truck, tell us some more about it. Is it a Chevy or GMC? Notice the chevy grill but GMC hood, although I like the combo personally. Paint looks great for sitting so long.

[lasher78]

it all chevy...350/th350...had it for like 13 yrs just now getting ready to start working on it here are some more pics...
Posted via Mobile Device

[lasher78]

it sat in a barn for last 12 yrs so paint held up pretty good...just got to get brakes and lines done and get motor going. going to get a fuel tank from lmc to go under bed then just fine tune to drive daily
Posted via Mobile Device

[1963c-10]

Very cool. I've always like the short steppers w/spare tire carrier. Keep us posted w/pics

[Johnny Too Bad]

I run mine without the tire mounted because I like the way it looks better without it. Since I took off the spare, I've been able to replace the big dumbo mirrors the PO had on it to see around the spare (this is an older picture).
I noticed most of the pics in this thread have the bigger mirrors. Was this the factory option on steppers with fender mount spares so you could see out of the drivers side mirror?

[1963c-10]

i run a 5" round mirror with no issues. its a factory mirror head
Posted via Mobile Device

[mr57]

Mine has just a 4 x 6 mirror on a stock post. I have a 235 65 15 on the carrier, and I can see the tire, but I can also see around it.

[Johnny Too Bad]

Originally Posted by 1963c-10

i run a 5" round mirror with no issues. its a factory mirror head
Posted via Mobile Device

I started thinking about it and I remembered that the PO had 15"x10" wheels on it when I bought it, so the spare stuck out far enough that he said he needed the bigger mirrors. This is the best pic I have of it with the spare still mounted, but you can tell it stuck out quite a bit.

[1963c-10]

I have a factory cast iron fender mount mirror arm also. Has a funny bend in it. I think there is a pic earlier on in the thread that shows it.


Also...found this in my archieve

[1963c-10]

Any more new additions?

[TypeSL2]

I wish I could find one of these carriers. I have the fender already mounted on the truck, just need the carrier and a tire for my spare wheel that I have. Any good spots to nab these from?

James

[1963c-10]

I'll keep my eyes peeled for you. I just got rid of one I grabbed at a swap meet for $50 only because I knew what it was and the price was right. I almost hate to say it, but they do pop up on ebay quite frequently. The beds were the same from late 55-66, so a carrier from those years will work. Just be sure you get the appropriate carrier for your bed...ie short or long bed. There are pics of the two different carriers earlier on in this thread. If I come across one, I'll send you a private message.

[TypeSL2]

Thank you so much. And in case I didn't already mention it, ours is a long bed stepside. I will keep my eyes peeled.

James

[1963c-10]

Yeah saw it too late in the trucks working thread. The big thing on a long bed is what fender you have. You can run a short bed fender on the long bed or a long bed fender, but cannot use the long bed fender on the short bed w/o clearance issues. The short bed carrier places the tire higher than the long bed. I personally think the long bed carriers look better and you can reach over the bed side easier. Let us know which fender you have so that we can keep our eyes open for the appropriate carrier.

[TypeSL2]

I will have to do some research, I am really not sure which fender I have. I think it is the short bed fender, but I can find out for sure tonight when I go home.

James

[1963c-10]

Originally Posted by TypeSL2

I will have to do some research, I am really not sure which fender I have. I think it is the short bed fender, but I can find out for sure tonight when I go home.

James

Post a pic and I can help identify it if you need too

[FetchMeAPepsi]

I just posted a bunch of measurements for the side mount carrier a few days ago. It's not very complicated. I'll bet if you didn't really HAVE to have OEM you could pay any backyard welder to fab one up in about an hour start to finish. It's just angle iron and rods with a plate on the front. See 'em here.

http://6066gmcclub.com/forum/showthr...9405#post49405

[TypeSL2]

Can you tell from this pic? To me, it looks like the long bed fender. I could be mistaken, but I need to get some better pics tonight. I have been wicked busy the past few days and I haven't even been able to drive it.



James

[1963c-10]

Looks like a long bed fender. The short beds had a hole cut in them for the braces to pass through. Although it'd be easy to drill a hole in it if you went with the high mount like the short beds have. The long beds mounted the tire lower