4L80E swap questions - The 1947 - Present Chevrolet & GMC Truck Message Board Network

usmcchevy · 10-26-2010, 12:12 PM

Looks like I'm going to end up with a 4L80e in my truck

. Those of you that have done this swap, will it fit under a low hump cab? What did you use for your trans cross member and mount? Any other advice? Thanks

MONTEZ · 10-26-2010, 03:31 PM

Quote:

Originally Posted by usmcchevy

Looks like I'm going to end up with a 4L80e in my truck

. Those of you that have done this swap, will it fit under a low hump cab? What did you use for your trans cross member and mount? Any other advice? Thanks

If you aren't running a drop member then it will clear fine, evne with a drop memebr it should clear, but will be a little tighter. As far as crossmembers goes, you can mod your stock one, or just get an aftermarket tube style one pretty cheap.

tonypaul · 10-27-2010, 09:29 AM

I just put in a 7.4l with the 4l80e in my 68 with no problems. My stock rear mount would have worked fine, but I used one from a old turbo trans am that I had laying around.

The only problem I might could see that if you had your motor pushed way back outside of the normal location. Then it would hit the cab, but just about any trans would hit.

usmcchevy · 10-27-2010, 01:24 PM

Thanks guys, I also PM'ed another member and he agreed with everything. It will clear low hump and use stock auto trans cross member. Thanks again, I'm sure I'll have more questions soon

Super73 · 10-30-2010, 02:39 PM

My motor is set far back and raised up that the passanger side coil is about 1/8" away from the firewall. I run and 80E and it does not hit.

10-26-2010, 12:12 PM	#1
usmcchevy Has more rust than truck... Join Date: Apr 2005 Location: Ivanhoe, MN Posts: 2,421	4L80E swap questions Looks like I'm going to end up with a 4L80e in my truck. Those of you that have done this swap, will it fit under a low hump cab? What did you use for your trans cross member and mount? Any other advice? Thanks __________________ 1972 Custom/10 SWB, 4.8/4l80e Build thread LSx Swap FAQ index

10-27-2010, 09:29 AM	#3
tonypaul Registered User Join Date: Nov 2009 Location: Austin Tx Posts: 639	Re: 4L80E swap questions I just put in a 7.4l with the 4l80e in my 68 with no problems. My stock rear mount would have worked fine, but I used one from a old turbo trans am that I had laying around. The only problem I might could see that if you had your motor pushed way back outside of the normal location. Then it would hit the cab, but just about any trans would hit.

10-27-2010, 01:24 PM	#4
usmcchevy Has more rust than truck... Join Date: Apr 2005 Location: Ivanhoe, MN Posts: 2,421	Re: 4L80E swap questions Thanks guys, I also PM'ed another member and he agreed with everything. It will clear low hump and use stock auto trans cross member. Thanks again, I'm sure I'll have more questions soon __________________ 1972 Custom/10 SWB, 4.8/4l80e Build thread LSx Swap FAQ index

10-30-2010, 02:39 PM	#5
Super73 Registered User Join Date: Nov 2007 Location: Bay Area, Ca Posts: 2,841	Re: 4L80E swap questions My motor is set far back and raised up that the passanger side coil is about 1/8" away from the firewall. I run and 80E and it does not hit. __________________ ------Motor---------------Bottle 60'---1.53---------------1.41 1/8---6.58 @ 105.92----5.87 @ 118.41 1/4---10.38 @ 126.97----9.24 @ 142.49



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.