TX Parting 72 Cheyenne Super

[lynnfield]

DDD

More cab pics

[blap]

Please put me in line for the air cleaner with spacer...and rear wheel tubs ...Thankyou

[lynnfield]

OK got to work on this some late last night and some more today.

Sharpie, I have pics of the gauges, emblems, and knobs. One stud on the "super" was broke on the side tha got hit, there might be enough to work with a barrel clip. Radiator hold downs are ok, it's just the uppers. I have you down for the lighter also, I'm assuming you want socket and all. I'll work on a total and send it to you

sjarrett71, radio works $15.00, under dash harness looks good so far, but I dont have it all the way out yet.

leddzepp, The rear harness is cut and spliced and pretty ugly, sorry.

c1069, working on the shipping, it's not looking good, I may not be able to get it done, but I have been working on it.

crig39, The trans lines, I thought were cut up are not. If you are still interested in them all and don't mind a few shipping bends then, $38.00 shipped for all

hotfun, Mark hopefully I will have these off tomorrow. I looked at the bed panel and found one ding only

makamer, The jack and handle are there no lug wrench. $40.00 shipped

Roughedup, a/c panel is not out yet, later tonight and I'll post pics

davedr, I have posted pics of the passenger fender, if you were refering to the inner fender it was no good. Let me know

67chevy1series, I will have the ebrake stuff together and pics later tonight. I want to make sure you get what you need

1967BBC10, column is out, $80.00 shipped without the steering wheel. If you need the wheel let me know, and I'll adjust

[sjarrett71]

Ok sounds good. I'll commit to the radio and wait until you have the harness all the way out to see what it looks like. It will include the neutral safety switch wiring right? If it's ok with you I'll wait to send payment until we decide if it's any good so I take care of it all at once.

[lynnfield]

clos69, I still have you second on the wheels, I'll know more tomorrow

wideside, wire looms are gone, heatshields depends on condition. I'll know more when the motor sells. (I have a guy local comming to look at it)

mcbassin, so far the under hood harness looks good, I'll know more later. dash harness depends on if the other guy/s pass. I'll let you know

dozerman, I got you in line

burb71, I'll check the bracket, and let you know if the tubs get to you. It's not a sport bumper

astevens, I have posted pics, but don't have it removed yet. I'd like to make sure of the condition, I'll be working on it tonight

1956 cameo, I'll post pics and prices for the items you asked about


I'm not caught up yet, still going to do some more tonight. Hopefully I didn't step over or skip anyone. Thanks Greg

[astevens]

Originally Posted by lynnfield

clos69, I still have you second on the wheels, I'll know more tomorrow

wideside, wire looms are gone, heatshields depends on condition. I'll know more when the motor sells. (I have a guy local comming to look at it)

mcbassin, so far the under hood harness looks good, I'll know more later. dash harness depends on if the other guy/s pass. I'll let you know

dozerman, I got you in line

burb71, I'll check the bracket, and let you know if the tubs get to you. It's not a sport bumper

astevens, I have posted pics, but don't have it removed yet. I'd like to make sure of the condition, I'll be working on it tonight

1956 cameo, I'll post pics and prices for the items you asked about


I'm not caught up yet, still going to do some more tonight. Hopefully I didn't step over or skip anyone. Thanks Greg

Ok. I appreciate it. Thanks
Aaron

[crig39]

how much for e-brake pedal assembly?

[lynnfield]

Late night

[lynnfield]

More pics

[lynnfield]

Still more

[67chevy1series]

wel i wont be needing the cable i will only need the two hooks and the e brake equalizer bracket and one e brake cable connector

[lynnfield]

sjarrett71, Radio is out, under dash harness is also out. The harness includes everything, door pin to door pin, dome light to fuse block. There is a small splice in the cig. lighter wire, and a small spot on the ignition plug that looks like it got warm at some point, (see pics) overall in good shape. Radio and dash harness, $80.00 shipped for it all

crig39, Lines and e-brake, $65.00 shipped for all

roughedup, A/c control is out, I have this pigtail for the switch from another truck I will include if you need it

67chevy1series, Is this all the ebrake stuff you need? Let me know, I can get more

Mcbassin, the under hood harness it out. It's in good condition, with some minor issues. There is a hole in the purple ignition wire at the block, someone checking voltage at some point I guess, the left headlamp plastic plug is missing, wires are there and ok, dist. wire has been spliced, temp sender wire missing plug, and I cut the wire at the fast idle solenoid, it was the only way to disconnect. $50.00 shipped

astevens, Outer box in good shape, the metal plate has some rust thru at the bottom. Inner box is in good shape, no issues. S duct is useable, but cracked around screw holes. The plastic diverter duct door is no good, and the metal floor duct is in good shape with no issues. $110.00 shipped

[lynnfield]

1967BBC10 has passed on the column, Repeeler you are up.

[lynnfield]

1956cameo, I have that stuff, ran out of time. Tomorrow, ok?

burb71, still need to look at that bracket

Blap, I believe I have another air cleaner and spacer, let me find it and post pics.

Thanks to all for being patient with me, I am off tomorrow, so I'll be back at it in the morning. Greg

[gastrader35]

what about the brake pedal and mounting bracket

[leddzepp]

Originally Posted by lynnfield

leddzepp, The rear harness is cut and spliced and pretty ugly, sorry.

No problem, thanks for checking.

[1956cameo]

Thanks! No rush just get to it when you can. I will keep an eye on the thread.

[mcbassin]

Originally Posted by lynnfield

sjarrett71, Radio is out, under dash harness is also out. The harness includes everything, door pin to door pin, dome light to fuse block. There is a small splice in the cig. lighter wire, and a small spot on the ignition plug that looks like it got warm at some point, (see pics) overall in good shape. Radio and dash harness, $80.00 shipped for it all

crig39, Lines and e-brake, $65.00 shipped for all

roughedup, A/c control is out, I have this pigtail for the switch from another truck I will include if you need it

67chevy1series, Is this all the ebrake stuff you need? Let me know, I can get more

Mcbassin, the under hood harness it out. It's in good condition, with some minor issues. There is a hole in the purple ignition wire at the block, someone checking voltage at some point I guess, the left headlamp plastic plug is missing, wires are there and ok, dist. wire has been spliced, temp sender wire missing plug, and I cut the wire at the fast idle solenoid, it was the only way to disconnect. $50.00 shippedastevens, Outer box in good shape, the metal plate has some rust thru at the bottom. Inner box is in good shape, no issues. S duct is useable, but cracked around screw holes. The plastic diverter duct door is no good, and the metal floor duct is in good shape with no issues. $110.00 shipped

I'm really only interested in the harness if I can get complete inside cab and under hood. Let me know if and when the guys ahead of me pass. and best price shipped together. thanks

[xman]

how much for all the tailgate parts in post #48 shipped to 60435 bussiness
would you happen to have a tailgate handle w/ screws and the rest of the inner hardware

Thanks
Dave

[lynnfield]

1956Cameo, A/c & alt. brackets, points dist, breather, spacer & tube. $80.00 shipped

Burb71, I looked at the bracket, it will go with the complete rear, sorry.

blap, Second breather, spacer and tube. Lid needs to be cleaned and painted the rest is clean. $40.00 shipped

gastrader35, brake pedal and mount, $35.00 shipped

Xman, tailgate trunions and hinges, $35.00 shipped. I don't have the inner hardware right now.

Hotfun, Mark, pics of the wheel tubs. I hope to have the bed apart in a few hours.

c1069, I have tried to get this done, but I'm sorry, I will not be able to ship the wheels.

[lynnfield]

clos69, You are up on the wheels and tires.

[bean]

just out of curiosity what would you want for the bed floor

[lynnfield]

Headed back out now, if I have missed anyone please let me know. Thanks, Greg

[lynnfield]

Bean, I'd take $75.00 for the whole thing or just the rear section, your choice come and get it!

[olblue60@aol.com]

Are the window regulators for sale? Do they operate smoothly? Thanks

John