Air Ride Install - '69 Chevrolet SWB Stepside - Page 2 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

GRIMSS · 12-23-2009, 07:39 PM

Looking good Doug. I need to come and check it out sometime.

Sinister · 12-23-2009, 08:20 PM

Lookin good Doug. Subscribed.

tcb-1 · 12-23-2009, 10:06 PM

was visited tonight by a box full of SMC valves from suicidedoors. first off, let me say that ***************** is a great place to do business with. I ordered these valves Monday, and here today and packaged well...... and I stole them @ $22 a piece. brand new, still in the factory bubble wrap. so now I have......

I removed the front springs tonight. here's a tip. if PB Blaster doesn't work to get the taper fit free, try a propane torch. only heat the spindle body, not the ball joint studs. the heat will expand the female taper fit. works like a charm eerytime I remove ball joints.

Chris, I plan on checking the front cups (drop ins) for fit and finish. I am also completely cleaning the front suspension as well as I can until I can put it on a rack. (hint hint scottrod?!)

got to thinking tonight about a "backup" in case the compressor failed. I may put a tee on at each bag and run a Schrader. bad luck tends to follow me, so anything to increase my odds in the other direction, I should explore.

*Dylan · 12-23-2009, 10:46 PM

Looking great, I can't wait to see how this progresses.

tcb-1 · 12-23-2009, 10:52 PM

Nate,
I used Rustoleum Industrial OIL based enamel in flat black in a can. it goes on smooth, self levels, and after dry, is fairly tough, especially when brushed on.

I was going to use POR15, but that stuff does NOT come off..... and eventually, I want the frame completely blasted and powdercoated. but for now, this is a viable choice that will come off under normal media blasting. I highly recommend the Rustoleum for normal underbody protection!!

Grandpa's CST · 12-24-2009, 05:33 PM

Sounds like the balljoint delema is solved, another way to do it is loosen the castle nut half of the way on the balljoint and while the joint is under spring load take two 3 lb hammers, one is held tight against one side of the spindle at the joint mounting and then the other hammer stikes the opposite side of the spindle temporarily oblonging the hole and releasing the two, make sure from here the spring is unloaded again before the nut is removed, usually works first or second hammer blow.

Like the project, subscribing.

soala70 · 12-24-2009, 09:34 PM

got to hook on

firedog · 12-24-2009, 10:33 PM

the rear install is pretty much bolt on. The front depending on how you do it is a little more demanding. Good Luck and you will want to go lower it will be just a matter of time. As far as a back up to the compressor put the schrader valve on the tank.
I sent you a pm also

72BlckButy · 12-25-2009, 04:20 PM

Okay Doug... what pieces did you unwrap this morning?

tcb-1 · 12-25-2009, 06:13 PM

how did you guess, Nato??!

got rear shock relocators (ECE) and front bag bracket/cups.

72BlckButy · 12-25-2009, 06:21 PM

Awesome!

Spray-Bomb · 12-26-2009, 01:19 PM

Gonna be sweet man

I have some dodge 17" wheels like yours, but never wanted to re-drill my axles & stuff for them to fit

As for the bags, I would buy the Slams... I have both & the Slams look much better made

As for the back up, I put a schrader on my tank as well

tcb-1 · 12-26-2009, 01:58 PM

spray bomber,
if you have a 67-70 truck you want to go 17" steelies on, these will work straight outta the box. they are Toyota FJ Cruiser rims, 17" x 7.5" wide on a 6 x 5.5" bc. I'm running a .75 spacer on them now, but once the truck is lower, I may remove them to tuck in better.

I've always liked your builds! thanks for coming by my build. my truck will still look like a 4x4 compared to some of your rigs!!!

!!

bad6772 · 12-27-2009, 12:33 AM

Doug awesome dude...You know you have my favorite truck of all time...Now you are going to make me get a 2nd job and put sweet pea on air huh? awesome dude.......Cannot not wait to see it.........

**invicta455** · 12-28-2009, 02:01 PM

Doug looking gooood

bigguy69 · 12-28-2009, 09:43 PM

looking good! subscribed!

tcb-1 · 12-28-2009, 11:43 PM

starting on the bolt on upper bag plates tonight. made my own drill bit to get to one of the holes.... call me McGyver!

took my suicidedoors drop in bag cups in this afternoon to get a shave. I estimated 5/8" off the total height would be good.

I'll get pics soon of my progress.

and.... thanks guys for the kind words. I hope I won't disappoint!

my67chevytruck · 12-29-2009, 01:11 AM

looking good Doug!

tcb-1 · 12-30-2009, 10:33 PM

got a little done over the past couple of nights. I also ordered my bags. with a lot of thought and with suicidedoors recommendations, I went with Airlift Dominator D2600's. can't wait 'til they show up on the doorstep! thanks again suicidedoors!

first, I took my drop in lower bag cups to my fabricator and had him cut them down approximately 5/8". they seem to sit perfect now. 5/8" doesn't sound like a lot, but it actually is when your trying to get as close to the floor as you can. here's the look of the cup in the pocket:

you know, specialized tools are expensive, but my God, they are so worth it. I even cut down a drill bit, and made my own short length bit. when you have to get something done, nothing should stand in the way......

nothing's more beautiful than a cab full of new parts.....

and for the grand unveiling..... in this pic, I raised the entire assembly up to when my tire was touching the inner fender. I measured and I still have about a inch to play with if I decide to ditch the inner fenders. but for now, this is where I'll dial the front end to.....

and lastly, this is where I would be without inner fenders.. and without a tire:

the first place I head to after we get back on the road is my muffler shop!! may have to modify the crossmember, buy a CPP unit, or drop out right under the cab. oh well, that decision for another day.

and before I wrap up this installment, I want to thank LOLIFE99 for giving me the kick in the pants to go on air. Keith is a great guy and knows his stuff. I owe you.......

hope everyone has a safe and an enjoyable New Year!!!

**LEEVON** · 12-30-2009, 11:47 PM

Looking good! Are you talking about the trailing arm or transmission crossmember?

tcb-1 · 12-30-2009, 11:49 PM

Leevon, should have clarified... the trailing arm cross member.

**lolife99** · 12-31-2009, 08:36 AM

Great Progress Doug! (Thanks for the kind words also)

If you decide to get a trailing arm crossmember,... DEFINITELY get the Porterbuilt unit.
http://porterbuiltstreetrods.com/site/?p=178

These are by far, the nicest ones out there. (I just happen to own one now)
Plus, they have the multiple mounting point to help dial in the pinion angle.
And,... you might as well get a set of Nate's new tubular trailing arms,... and,...

Keep up the good work!

72BlckButy · 12-31-2009, 09:34 AM

Nice work Doug!

I was in your hometown for a little while yesterday. Needless to say they didn't receive any snow...

powell72 · 12-31-2009, 08:05 PM

Looks like you're making some good progress.

I gotta ask, is your truck always that clean?

tcb-1 · 12-31-2009, 11:59 PM

Quote:

Originally Posted by powell72

Looks like you're making some good progress.

I gotta ask, is your truck always that clean?

As a matter of fact Chris, I'm on medication so I'm not so clean and organized

!!

12-23-2009, 07:39 PM	#26
GRIMSS --------------- Join Date: Mar 2008 Location: Central Missouri Posts: 1,791	Re: Air Ride Install - '69 Chevrolet SWB Stepside Looking good Doug. I need to come and check it out sometime. __________________ 2001 GMC SIERRA 1956 Chevy Panel *Build Page* with a Scott's Hotrods IFS 1953 Chevy trucks *Project Dime Time* 1968 Camaro 1968 Volksrod "NOBACK" 55-59 one piece window *Video* 55-59 one piece window *template files* Jared

12-23-2009, 08:20 PM	#27
Sinister Between Trucks... Join Date: Mar 2002 Location: Los Angeles, CA. Posts: 3,830	Re: Air Ride Install - '69 Chevrolet SWB Stepside Lookin good Doug. Subscribed. __________________ Beat it to fit, Paint it to match...

12-23-2009, 10:06 PM	#28
tcb-1 Nothing to see here..... Join Date: Jun 2007 Location: Shawnee, KS Posts: 4,625	Re: Air Ride Install - '69 Chevrolet SWB Stepside was visited tonight by a box full of SMC valves from suicidedoors. first off, let me say that *************** is a great place to do business with. I ordered these valves Monday, and here today and packaged well...... and I stole them @ $22 a piece. brand new, still in the factory bubble wrap. so now I have...... I removed the front springs tonight. here's a tip. if PB Blaster doesn't work to get the taper fit free, try a propane torch. only heat the spindle body, not the ball joint studs. the heat will expand the female taper fit. works like a charm eerytime I remove ball joints. Chris, I plan on checking the front cups (drop ins) for fit and finish. I am also completely cleaning the front suspension as well as I can until I can put it on a rack. (hint hint scottrod?!) got to thinking tonight about a "backup" in case the compressor failed. I may put a tee on at each bag and run a Schrader. bad luck tends to follow me, so anything to increase my odds in the other direction, I should explore. __________________ Doug THANK YOU** to our American Soldiers & Veterans - POW MIA "You will NEVER be forgotten". The democracy will cease to exist when you take away from those who are willing to work and give to those who would not. Thomas Jefferson Last edited by tcb-1; 12-23-2009 at 10:41 PM.

12-23-2009, 10:46 PM	#29
*Dylan Mean Buzzin' Half Dozen Join Date: Mar 2008 Location: Orlando, Florida Posts: 1,081	Re: Air Ride Install - '69 Chevrolet SWB Stepside Looking great, I can't wait to see how this progresses. __________________ "War is an ugly thing, but not the ugliest of things. The decayed and degraded state of moral and patriotic feeling which thinks that nothing is worth war is much worse. The person who has nothing for which he is willing to fight, nothing which is more important than his own personal safety, is a miserable creature and has no chance of being free unless made and kept so by the exertions of better men than himself." MY TRUCK (Now for sale) 1967 C10 SWB *Dylan* IIMY?

12-23-2009, 10:52 PM	#30
tcb-1 Nothing to see here..... Join Date: Jun 2007 Location: Shawnee, KS Posts: 4,625	Re: Air Ride Install - '69 Chevrolet SWB Stepside Nate, I used Rustoleum Industrial OIL based enamel in flat black in a can. it goes on smooth, self levels, and after dry, is fairly tough, especially when brushed on. I was going to use POR15, but that stuff does NOT come off..... and eventually, I want the frame completely blasted and powdercoated. but for now, this is a viable choice that will come off under normal media blasting. I highly recommend the Rustoleum for normal underbody protection!! __________________ Doug THANK YOU to our American Soldiers & Veterans - POW MIA "You will NEVER be forgotten". The democracy will cease to exist when you take away from those who are willing to work and give to those who would not. Thomas Jefferson

12-24-2009, 05:33 PM	#31
Grandpa's CST Registered User Join Date: Apr 2007 Location: Seattle area Posts: 28	Re: Air Ride Install - '69 Chevrolet SWB Stepside Sounds like the balljoint delema is solved, another way to do it is loosen the castle nut half of the way on the balljoint and while the joint is under spring load take two 3 lb hammers, one is held tight against one side of the spindle at the joint mounting and then the other hammer stikes the opposite side of the spindle temporarily oblonging the hole and releasing the two, make sure from here the spring is unloaded again before the nut is removed, usually works first or second hammer blow. Like the project, subscribing. __________________ ........................ ..........._____\|__\___ ..........\|_(O)_____(O)]

12-24-2009, 09:34 PM	#32
soala70 Registered User Join Date: Mar 2002 Location: geneva al usa Posts: 343	Re: Air Ride Install - '69 Chevrolet SWB Stepside got to hook on __________________ bogey5

12-24-2009, 10:33 PM	#33
firedog Registered User Join Date: Jun 2000 Location: Festus, Missouri Posts: 1,004	Re: Air Ride Install - '69 Chevrolet SWB Stepside the rear install is pretty much bolt on. The front depending on how you do it is a little more demanding. Good Luck and you will want to go lower it will be just a matter of time. As far as a back up to the compressor put the schrader valve on the tank. I sent you a pm also __________________ SOLD 1968 Chevy SWB Fleet 350/350 combo Tach/tilt/buddy buckets Bagged/18" Wheels Black on Black Project "Pandemic" the Farm Rat 1927 Chevy Capitol Truck Rat rod '30 Model A Frame Dual Carb 5.3 LS http://www.67-72chevytrucks.com/vboa...d.php?t=804162 2007 GMC 4 DOOR 2WD BUILT 5.3 STAGE 3 CAM 93 TUNE LIFTED 22X12 WHEELS 33" TIRES 2023 Jeep RENEGADE Wifes ride Last edited by firedog; 12-24-2009 at 11:05 PM.

12-25-2009, 04:20 PM	#34
72BlckButy Tot Roddin' Join Date: Apr 2005 Location: Mid-MO Posts: 24,461	Re: Air Ride Install - '69 Chevrolet SWB Stepside Okay Doug... what pieces did you unwrap this morning? __________________ -Nate 1969 CST SWB - Project Blank Slate (4.5/6" ECE Static Drop, 6-lug disc brake upgrade (manual), Billet Specialties Vintec 20x8.5 255/40 (F) 20x10 295/40 (R), 250 I-6) 1960 AMF Skylark - Tot Roddin' (Lowered with custom frame; soon to include custom push bar and interior) 2008 Silverado CrewCab 1LT (5.3L, 3:73, 4x4, LT1, Z-71, Towing Package)

12-25-2009, 06:13 PM	#35
tcb-1 Nothing to see here..... Join Date: Jun 2007 Location: Shawnee, KS Posts: 4,625	Re: Air Ride Install - '69 Chevrolet SWB Stepside how did you guess, Nato??! got rear shock relocators (ECE) and front bag bracket/cups. __________________ Doug THANK YOU to our American Soldiers & Veterans - POW MIA "You will NEVER be forgotten". The democracy will cease to exist when you take away from those who are willing to work and give to those who would not. Thomas Jefferson

12-25-2009, 06:21 PM	#36
72BlckButy Tot Roddin' Join Date: Apr 2005 Location: Mid-MO Posts: 24,461	Re: Air Ride Install - '69 Chevrolet SWB Stepside Awesome! __________________ -Nate 1969 CST SWB - Project Blank Slate (4.5/6" ECE Static Drop, 6-lug disc brake upgrade (manual), Billet Specialties Vintec 20x8.5 255/40 (F) 20x10 295/40 (R), 250 I-6) 1960 AMF Skylark - Tot Roddin' (Lowered with custom frame; soon to include custom push bar and interior) 2008 Silverado CrewCab 1LT (5.3L, 3:73, 4x4, LT1, Z-71, Towing Package)

12-26-2009, 01:19 PM	#37
Spray-Bomb Texas Big Wig Join Date: Jan 2007 Location: Mineola, Texas Posts: 5,620	Re: Air Ride Install - '69 Chevrolet SWB Stepside Gonna be sweet man I have some dodge 17" wheels like yours, but never wanted to re-drill my axles & stuff for them to fit As for the bags, I would buy the Slams... I have both & the Slams look much better made As for the back up, I put a schrader on my tank as well __________________ Just not low enough... ----------------------------- Sinister Killer

12-26-2009, 01:58 PM	#38
tcb-1 Nothing to see here..... Join Date: Jun 2007 Location: Shawnee, KS Posts: 4,625	Re: Air Ride Install - '69 Chevrolet SWB Stepside spray bomber, if you have a 67-70 truck you want to go 17" steelies on, these will work straight outta the box. they are Toyota FJ Cruiser rims, 17" x 7.5" wide on a 6 x 5.5" bc. I'm running a .75 spacer on them now, but once the truck is lower, I may remove them to tuck in better. I've always liked your builds! thanks for coming by my build. my truck will still look like a 4x4 compared to some of your rigs!!! !! __________________ Doug THANK YOU to our American Soldiers & Veterans - POW MIA "You will NEVER be forgotten". The democracy will cease to exist when you take away from those who are willing to work and give to those who would not. Thomas Jefferson

12-27-2009, 12:33 AM	#39
bad6772 Official Site Guitar Shredder Join Date: May 2006 Location: Oz Posts: 3,952	Re: Air Ride Install - '69 Chevrolet SWB Stepside Doug awesome dude...You know you have my favorite truck of all time...Now you are going to make me get a 2nd job and put sweet pea on air huh? awesome dude.......Cannot not wait to see it.........

12-28-2009, 02:01 PM	#40
invicta455 Senior Member Join Date: May 2009 Location: greensboro north carolina Posts: 531	Re: Air Ride Install - '69 Chevrolet SWB Stepside Doug looking gooood



Register or Log In To remove these advertisements.

12-28-2009, 09:43 PM	#41
bigguy69 dazed and confused Join Date: Jul 2008 Location: marion nc Posts: 1,649	Re: Air Ride Install - '69 Chevrolet SWB Stepside looking good! subscribed! __________________ members met: redbaron69, billsbowtie,nc67

12-28-2009, 11:43 PM	#42
tcb-1 Nothing to see here..... Join Date: Jun 2007 Location: Shawnee, KS Posts: 4,625	Re: Air Ride Install - '69 Chevrolet SWB Stepside starting on the bolt on upper bag plates tonight. made my own drill bit to get to one of the holes.... call me McGyver! took my suicidedoors drop in bag cups in this afternoon to get a shave. I estimated 5/8" off the total height would be good. I'll get pics soon of my progress. and.... thanks guys for the kind words. I hope I won't disappoint! __________________ Doug THANK YOU to our American Soldiers & Veterans - POW MIA "You will NEVER be forgotten". The democracy will cease to exist when you take away from those who are willing to work and give to those who would not. Thomas Jefferson Last edited by tcb-1; 12-28-2009 at 11:44 PM.

12-29-2009, 01:11 AM	#43
my67chevytruck Under Construction Join Date: Oct 2007 Location: Midlothian,TX (DFW) Posts: 4,555	Re: Air Ride Install - '69 Chevrolet SWB Stepside looking good Doug! __________________ Heath subscribe to the board here: http://67-72chevytrucks.com/vboard/payments.php http://67-72chevytrucks.com/vboard/s...d.php?t=157669 FAQ how to's 1956 Chevy Apache 1967 C10 SWB FleetSide (under construction) 1969 K10 SWB FleetSide (Future Build) 1972 C10 SWB Stepside (Future Build) 56 chevy truck : http://www.cardomain.com/ride/2955823/1 67 truck build: http://www.67-72chevytrucks.com/vboard/showthread.php?t=281357/1 69 k10: http://67-72chevytrucks.com/vboard/s...d.php?t=389470

12-30-2009, 10:33 PM	#44
tcb-1 Nothing to see here..... Join Date: Jun 2007 Location: Shawnee, KS Posts: 4,625	Re: Air Ride Install - '69 Chevrolet SWB Stepside got a little done over the past couple of nights. I also ordered my bags. with a lot of thought and with suicidedoors recommendations, I went with Airlift Dominator D2600's. can't wait 'til they show up on the doorstep! thanks again suicidedoors! first, I took my drop in lower bag cups to my fabricator and had him cut them down approximately 5/8". they seem to sit perfect now. 5/8" doesn't sound like a lot, but it actually is when your trying to get as close to the floor as you can. here's the look of the cup in the pocket: you know, specialized tools are expensive, but my God, they are so worth it. I even cut down a drill bit, and made my own short length bit. when you have to get something done, nothing should stand in the way...... nothing's more beautiful than a cab full of new parts..... and for the grand unveiling..... in this pic, I raised the entire assembly up to when my tire was touching the inner fender. I measured and I still have about a inch to play with if I decide to ditch the inner fenders. but for now, this is where I'll dial the front end to..... and lastly, this is where I would be without inner fenders.. and without a tire: the first place I head to after we get back on the road is my muffler shop!! may have to modify the crossmember, buy a CPP unit, or drop out right under the cab. oh well, that decision for another day. and before I wrap up this installment, I want to thank LOLIFE99 for giving me the kick in the pants to go on air. Keith is a great guy and knows his stuff. I owe you....... hope everyone has a safe and an enjoyable New Year!!! __________________ Doug THANK YOU to our American Soldiers & Veterans - POW MIA "You will NEVER be forgotten". The democracy will cease to exist when you take away from those who are willing to work and give to those who would not. Thomas Jefferson

12-30-2009, 11:47 PM	#45
LEEVON Registered User Join Date: Jul 2006 Location: Ozark, MO Posts: 4,887	Re: Air Ride Install - '69 Chevrolet SWB Stepside Looking good! Are you talking about the trailing arm or transmission crossmember? __________________ '20 Silverado Trail Boss ~ '17 Tahoe ~ '79 K15 Sierra Grande ~ '76 Blazer 2wd ~ '71 Cheyenne swb ~ '55 Pontiac Safari ~'50 3100 bagged ~ '80 Wife ~ Late model kids Last edited by LEEVON; 12-30-2009 at 11:48 PM.

12-30-2009, 11:49 PM	#46
tcb-1 Nothing to see here..... Join Date: Jun 2007 Location: Shawnee, KS Posts: 4,625	Re: Air Ride Install - '69 Chevrolet SWB Stepside Leevon, should have clarified... the trailing arm cross member. __________________ Doug THANK YOU to our American Soldiers & Veterans - POW MIA "You will NEVER be forgotten". The democracy will cease to exist when you take away from those who are willing to work and give to those who would not. Thomas Jefferson

12-31-2009, 08:36 AM	#47
lolife99 67-72 parts collector,… Join Date: Nov 2002 Location: Mid-MO Posts: 22,684	Re: Air Ride Install - '69 Chevrolet SWB Stepside Great Progress Doug! (Thanks for the kind words also) If you decide to get a trailing arm crossmember,... DEFINITELY get the Porterbuilt unit. http://porterbuiltstreetrods.com/site/?p=178 These are by far, the nicest ones out there. (I just happen to own one now) Plus, they have the multiple mounting point to help dial in the pinion angle. And,... you might as well get a set of Nate's new tubular trailing arms,... and,... Keep up the good work!

12-31-2009, 09:34 AM	#48
72BlckButy Tot Roddin' Join Date: Apr 2005 Location: Mid-MO Posts: 24,461	Re: Air Ride Install - '69 Chevrolet SWB Stepside Nice work Doug! I was in your hometown for a little while yesterday. Needless to say they didn't receive any snow... __________________ -Nate 1969 CST SWB - Project Blank Slate (4.5/6" ECE Static Drop, 6-lug disc brake upgrade (manual), Billet Specialties Vintec 20x8.5 255/40 (F) 20x10 295/40 (R), 250 I-6) 1960 AMF Skylark - Tot Roddin' (Lowered with custom frame; soon to include custom push bar and interior) 2008 Silverado CrewCab 1LT (5.3L, 3:73, 4x4, LT1, Z-71, Towing Package)

12-31-2009, 08:05 PM	#49
powell72 Senior Member Join Date: Jan 2005 Location: Loveland Co. Posts: 3,098	Re: Air Ride Install - '69 Chevrolet SWB Stepside Looks like you're making some good progress. I gotta ask, is your truck always that clean? __________________ Chris 74 Custom Deluxe SWB 350/350/3.73’s 99 2wd Silverado RCSB 5.3/4L60/3.90’s http://www.classictrucks.com/feature...short_bed.html

Register or Log In To remove these advertisements.