The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Engine & Drivetrain

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 06-12-2021, 12:15 AM   #1
fourspeedwagon
Registered User
 
fourspeedwagon's Avatar
 
Join Date: Oct 2010
Location: Yakima Valley, Washington
Posts: 575
Please help me diagnose an overheating 283

So— this isn’t in one of my pickups, it’s in my ‘57 Bel Air.
All stock 283 power pack. I’ve had it for a couple years and I knew the radiator leaked so I thought that was why it’d heat up. Last year I had the radiator completely rebuilt but of course Nothing happened last year and I don’t even remember taking it out.
The other day I took it off the battery tender and put a couple gallons of non ethanol in. Fired up easily and after I had my wash buckets ready I decided to take it around the block before cleaning it up. I watched the temp gauge climb and circled the block (a country block so maybe 2) and when I got back home it puked a bunch of antifreeze onto my driveway. After it cooled I put a new 180 thermostat in. Didn’t help. I called the radiator shop that redid it and left a message. Guy called me while I was at work and said I should check the temps at different spots with an infrared thermometer. I did, but of course they were closed by the time I got back and could call them.
A couple minutes warm up and a trip around the block gave me these temps:
Top tank of radiator 160 degrees
Bottom of radiator 125
Water pump 225
Top and bottom radiator hoses were hot to the touch but only showed 160 or so I think because the rubber didn’t heat as quickly as the metal.
I turned on the heat in the car and it was working.
When I turn off the car it “diesels” or runs on.
Outside ambient temp 65
I backed off the timing a bit and didn’t notice a difference either.
My thought is water pump but the heater putting out heat is causing me doubt on that.
Thanks for your help. It’s not one of my pickups but this is the forum I frequent- haven’t found a tri5 group that I fit in..
__________________
1951 GMC 250 Open Express Pickup
1968 Suburban C10
1971 C20 Olive
“People are shocked when they find out I’m not a good electrician”
Dad told me “Son, never strike a man in anger- unless you’re certain you can get away with it”

Last edited by fourspeedwagon; 06-12-2021 at 12:46 AM.
fourspeedwagon is offline   Reply With Quote
Old 06-12-2021, 12:41 AM   #2
geezer#99
Registered User
 
geezer#99's Avatar
 
Join Date: Aug 2009
Location: Bowser
Posts: 13,494
Re: Please help me diagnose an overheating 283

If you just have the stock overflow hose that vents onto the ground then it’s just puking out the excess coolant.
It should level off at a couple inches below the top when you check it cold.
The air space at the top is needed for coolant expansion when up to temp.
geezer#99 is offline   Reply With Quote
Old 06-12-2021, 11:05 AM   #3
paul mora
Senior Member
 
Join Date: Jan 2009
Location: huntington beach california
Posts: 975
Re: Please help me diagnose an overheating 283

Your radiator cap my be bad they are rated for a lbs pressure. The cap may be bad so car is running at correct temp and radiator cap is bacd so it releases the cool out the overflow.
__________________
Pulatoy
paul mora is offline   Reply With Quote
Old 06-12-2021, 04:49 PM   #4
AcampoDave
Registered User
 
AcampoDave's Avatar
 
Join Date: Feb 2013
Location: central California
Posts: 2,723
Re: Please help me diagnose an overheating 283

I always thought a car diesels after shut off because it wants more timing, not backing it off.
AcampoDave is offline   Reply With Quote
Old 06-12-2021, 07:10 PM   #5
fourspeedwagon
Registered User
 
fourspeedwagon's Avatar
 
Join Date: Oct 2010
Location: Yakima Valley, Washington
Posts: 575
Re: Please help me diagnose an overheating 283

I don’t think it’s the cap causing it to overheat.

I bought a new water pump and hoses and I’ll see if it’s that. Not sure what else to try.
Thanks again
__________________
1951 GMC 250 Open Express Pickup
1968 Suburban C10
1971 C20 Olive
“People are shocked when they find out I’m not a good electrician”
Dad told me “Son, never strike a man in anger- unless you’re certain you can get away with it”
fourspeedwagon is offline   Reply With Quote
Old 06-12-2021, 07:18 PM   #6
Dead Parrot
Registered User
 
Join Date: Aug 2012
Location: Oklahoma City, OK
Posts: 2,461
Re: Please help me diagnose an overheating 283

2nd the though on the overflow. The older no overflow tank radiators usually had a bit of air space for thermal expansion. Once they added the tank, you filled the radiator to the top.

Check the sides of the motor block with your temp gun. Also the intake next to the thermostat and the top of the thermostat housing.

Your temps so far make me suspect the water pump but easier to take more readings then pull the pump.


On the after run, usually due to too much idle. Add the timing back and maybe more if it still starts easy hot. Adjust idle mix for best rpm then turn in(lean up) about a 1/4 turn. Also possible there is a vacuum leak that a PO 'fixed' by advancing the idle adjustment.
Dead Parrot is offline   Reply With Quote
Old 06-12-2021, 07:47 PM   #7
paul mora
Senior Member
 
Join Date: Jan 2009
Location: huntington beach california
Posts: 975
Re: Please help me diagnose an overheating 283

If it is puking coolant it’s coming out at the cap. If it is not overheating the cap is bad. It’s designed to hold pressure at a lbs of spring load Good lucky
__________________
Pulatoy
paul mora is offline   Reply With Quote
Old 06-13-2021, 12:36 AM   #8
fourspeedwagon
Registered User
 
fourspeedwagon's Avatar
 
Join Date: Oct 2010
Location: Yakima Valley, Washington
Posts: 575
Re: Please help me diagnose an overheating 283

It was overheating before the radiator was rebuilt and they supplied a new 10# cap with it at that time.
Thanks again
__________________
1951 GMC 250 Open Express Pickup
1968 Suburban C10
1971 C20 Olive
“People are shocked when they find out I’m not a good electrician”
Dad told me “Son, never strike a man in anger- unless you’re certain you can get away with it”
fourspeedwagon is offline   Reply With Quote
Old 06-13-2021, 08:42 AM   #9
geezer#99
Registered User
 
geezer#99's Avatar
 
Join Date: Aug 2009
Location: Bowser
Posts: 13,494
Re: Please help me diagnose an overheating 283

What’s the coolant level in the rad when the motor is cold?
Do you fill it right to the top?
geezer#99 is offline   Reply With Quote
Old 06-13-2021, 08:49 AM   #10
cadillac_al
Registered User
 
Join Date: Oct 2013
Location: Maine
Posts: 2,325
Re: Please help me diagnose an overheating 283

So the radiator is puking coolant at 160 degrees? That's not over-heating it's just expansion. I would add an expansion tank. I had to do that on my 70 Impala to keep all the coolant in the cooling system.
__________________
76 Chevy K20
76 GMC K15
77 Chevy C10
77 Chevy K10
cadillac_al is offline   Reply With Quote
Old 06-13-2021, 02:20 PM   #11
MySons68C20
Senior Member
 
MySons68C20's Avatar
 
Join Date: Sep 2014
Location: Wenatchee, Wa
Posts: 892
Re: Please help me diagnose an overheating 283

10 lb cap is to low imho....replace with a 16 lb and see what that does.
Had a similar prob with all new components turned out the 16 lb and puke tank solved it.
MySons68C20 is offline   Reply With Quote
Old 06-13-2021, 10:28 PM   #12
paul mora
Senior Member
 
Join Date: Jan 2009
Location: huntington beach california
Posts: 975
Re: Please help me diagnose an overheating 283

Be sure to let us know how you sole the problem. I am not sure exactly what is wrong at this point. Is it overheating or just puking water. I didn’t know a 10 lb existed Be sure to change it out
__________________
Pulatoy
paul mora is offline   Reply With Quote
Old 06-13-2021, 10:35 PM   #13
fourspeedwagon
Registered User
 
fourspeedwagon's Avatar
 
Join Date: Oct 2010
Location: Yakima Valley, Washington
Posts: 575
Re: Please help me diagnose an overheating 283

Thanks Paul- I will update the posting once I get it solved. I have a message in to the shop that rebuilt the radiator as well as a new pump and hose awaiting my next day off from work. Also, a mild acid to flush the block with.
It’s definitely overheating not just overfilled. Temp gauge pegs, it runs on after shutting off and any water that hits the intake or water pump will sizzle violently and boil away. She’s hot.
It’ll be Wednesday night or Thursday before I can work on it again.
Thanks for your suggestions— Greg
__________________
1951 GMC 250 Open Express Pickup
1968 Suburban C10
1971 C20 Olive
“People are shocked when they find out I’m not a good electrician”
Dad told me “Son, never strike a man in anger- unless you’re certain you can get away with it”
fourspeedwagon is offline   Reply With Quote
Old 06-14-2021, 10:41 AM   #14
paul mora
Senior Member
 
Join Date: Jan 2009
Location: huntington beach california
Posts: 975
Re: Please help me diagnose an overheating 283

No mention of the type of cooling fan. It my be the problem if yor have a clutch fan it is is not working. Be sure your is working and you have a good fan shroud t funnel the air through the radiator
__________________
Pulatoy
paul mora is offline   Reply With Quote
Old 06-15-2021, 06:39 PM   #15
vince1
Registered User
 
Join Date: Jan 2013
Location: Calgary Alberta
Posts: 1,162
Re: Please help me diagnose an overheating 283

Maybe when you pull the water pump off you'll find the impeller off or broken. It happened to me once.
vince1 is offline   Reply With Quote
Old 06-17-2021, 05:16 PM   #16
fourspeedwagon
Registered User
 
fourspeedwagon's Avatar
 
Join Date: Oct 2010
Location: Yakima Valley, Washington
Posts: 575
Re: Please help me diagnose an overheating 283

New pump, hoses and thermostat and it’s running nice and cool. Just below half on the gauge. Let it idle a while and then drove it for the same lap around the area and back - didn’t boil or hiss.
I don’t see anything wrong with the old pump but that seems to be what it was.

Thanks again folks- Greg
Attached Images
 
__________________
1951 GMC 250 Open Express Pickup
1968 Suburban C10
1971 C20 Olive
“People are shocked when they find out I’m not a good electrician”
Dad told me “Son, never strike a man in anger- unless you’re certain you can get away with it”
fourspeedwagon is offline   Reply With Quote
Old 06-17-2021, 07:58 PM   #17
cwcarpenter98
Senior Member


 
cwcarpenter98's Avatar
 
Join Date: Jan 2018
Location: Hickory Flat, GA
Posts: 4,419
Re: Please help me diagnose an overheating 283

Good deal that it's fixed. Did you pop the back cover off the pump?
__________________
Christian Carpenter

1963 C10 - Frankentruck 283, 3 speed with overdrive
Overdrive wiring here
1963-ish truck bed trailer - Half-Wit

1981 C10 - Penny 305, th350

1995 Dodge Dakota Sport

"I'll put it simple: if you're going hard enough left, you'll find yourself turning right." - Doc Hudson
cwcarpenter98 is offline   Reply With Quote
Old 06-17-2021, 11:31 PM   #18
fourspeedwagon
Registered User
 
fourspeedwagon's Avatar
 
Join Date: Oct 2010
Location: Yakima Valley, Washington
Posts: 575
Re: Please help me diagnose an overheating 283

I did and I hammered the shaft end so I could see the impeller. Looks ok to me? No broken fins or anything obvious like that.
I let it sit overnight with descaler in the block and flushed it well. The tip hose was pretty soft but not collapsed. Thinking the pump was the worst but several little things piled up to make put it over the top.
__________________
1951 GMC 250 Open Express Pickup
1968 Suburban C10
1971 C20 Olive
“People are shocked when they find out I’m not a good electrician”
Dad told me “Son, never strike a man in anger- unless you’re certain you can get away with it”
fourspeedwagon is offline   Reply With Quote
Old 06-21-2021, 02:39 PM   #19
rockosocko
Registered User
 
Join Date: Dec 2013
Location: N/W Mississippi 'Yall
Posts: 44
Re: Please help me diagnose an overheating 283

I know it might sound goofy, but on a Sunday or weekend, find a warehouse somewhere that has 'ramps' to where you can come in from the side and get that nose pointed up as much as you can. Pop the hood, and the radiator cap and see if you can "burp" any air pockets.
Another thing is that although some people have the original engine, it's NEVER been flushed correctly, and after 50-60yrs, there's a lot of rust and crap down between the cylinders in the block. And that insulates the bottom of the cylinders.

There's a bunch of better flushes out there now. SO doesn't take a really long time to get all that crap out. Even if you can get those two pipe plugs out of the middle bottom of the Chevy blocks. And a bent piece of coat hanger to dig around while the water is being forced through.

And with all these 'import' Thermostats, a couple 1/8" holes drilled around the skirts can't hurt. That way you always have some kind of water flowing around. Even if it sticks shut. (..funny how they never seem to stick OPEN!)
rockosocko is offline   Reply With Quote
Old 06-21-2021, 10:41 PM   #20
AcampoDave
Registered User
 
AcampoDave's Avatar
 
Join Date: Feb 2013
Location: central California
Posts: 2,723
Re: Please help me diagnose an overheating 283

What Rocko said about the crap between the cylinders is so true. I actually pulled my old 283 to put it on a stand in the driveway, then I pulled the freeze plugs and flushed the block thru the holes with one of these https://www.homedepot.com/p/Gilmour-...E&gclsrc=aw.ds I turned it upside down and did it some more and I made a huge rusty powdery puddle of nastiness. Gunk just came rolling out of those freeze plug openings. It all went well. I drained the oil first course, pulled the carb and distributor and sealed those holes with plastic bags and flashing tape and just blasted the water jacket until the water finally ran clean.

Last edited by AcampoDave; 06-21-2021 at 10:49 PM.
AcampoDave is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 06:03 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com