Drive shaft ujoint straps - The 1947 - Present Chevrolet & GMC Truck Message Board Network

kaycee · 05-26-2021, 09:14 PM

Swapped out the 63 rearend for one out of a 71 went in without a problem ,that is until I went to bolt the rear DS up. The straps are to small from my 63 to go into the 71 the holes are 3/16" to narrow.So the parts guy gave me a new strap kit MOOG 330-10 they are the right spacing but the bolts are biggir and wont fit in the yoke

Parts house was closed by the time I got home plus its 35 miles 1 way ,keep telling myself to drill them out to the needed size. I have a 69 C-10 and they are the same as the 63 I guess I could swap the yoke, Any advice would be great about now

**cwcarpenter98** · 05-26-2021, 09:28 PM

Can you use the old bolts with the new straps?

kaycee · 05-26-2021, 09:46 PM

They are u bolts not straps ,my bad ,63 are 5/16 and the 71 is 3/8 " diameter bolts or close to that size . I would have to go measure for sure, so I went and looked and the pad that the u bolt slides through is 1 " on the 63 and on the 71 it is 1 1/2" I wonder if it takes a strap and bolts any one have a # book 63 is 3896838 and the # on the 71 is 3856525
Looks like I need the straps as the yoke is threaded ,see sometimes it pays to talk to yourself or think outloud .

**Mike_The_Grad** · 06-02-2021, 01:06 PM

I have a 1972 c10 with 12 bolt rearend. My pinion yoke takes the u joint straps. It took me about 10 years to find out where to get them. And I'm not joking. I found a set on summit. Yukon gear makes them but they want $40+s&h. Which is ridiculous. One day I was explaining this to a friend of mine and he suggested that I try the local napa store. Not feeling to confident about it I went in asked the counter guy and he knew exactly what I was looking for.(he owns a 72 c10 swb.) Sure enough he had them in stock. For about $10. I was expecting at least $20based off the ones I seen on summit. Try the local napa. I will try and find that box or at least a part number if it helps.

kaycee · 06-02-2021, 05:55 PM

Yeah I found out they needed straps allso ,went to NAPA and they had them in stock around $6.00 told the parts guy to look up 73 C-10 and booom there it was

**Mike_The_Grad** · 06-02-2021, 07:15 PM

Napa part number I have for the u joint straps is: UJ360-10

05-26-2021, 09:14 PM	#1
kaycee Registered User Join Date: Jan 2000 Location: Wyoming USA Posts: 2,445	Drive shaft ujoint straps Swapped out the 63 rearend for one out of a 71 went in without a problem ,that is until I went to bolt the rear DS up. The straps are to small from my 63 to go into the 71 the holes are 3/16" to narrow.So the parts guy gave me a new strap kit MOOG 330-10 they are the right spacing but the bolts are biggir and wont fit in the yoke Parts house was closed by the time I got home plus its 35 miles 1 way ,keep telling myself to drill them out to the needed size. I have a 69 C-10 and they are the same as the 63 I guess I could swap the yoke, Any advice would be great about now __________________ 2001 Silverado K-1500 2005 FXDWG stage3 69 CHEVY Short/Step 327/4L60 373 posi 63 IMPALA 327

05-26-2021, 09:28 PM	#2
cwcarpenter98 Senior Member Join Date: Jan 2018 Location: Hickory Flat, GA Posts: 4,421	Re: Drive shaft ujoint straps Can you use the old bolts with the new straps? __________________ Christian Carpenter 1963 C10 - Frankentruck 283, 3 speed with overdrive Overdrive wiring here 1963-ish truck bed trailer - Half-Wit 1981 C10 - Penny 305, th350 1995 Dodge Dakota Sport "I'll put it simple: if you're going hard enough left, you'll find yourself turning right." - Doc Hudson

05-26-2021, 09:46 PM	#3
kaycee Registered User Join Date: Jan 2000 Location: Wyoming USA Posts: 2,445	Re: Drive shaft ujoint straps They are u bolts not straps ,my bad ,63 are 5/16 and the 71 is 3/8 " diameter bolts or close to that size . I would have to go measure for sure, so I went and looked and the pad that the u bolt slides through is 1 " on the 63 and on the 71 it is 1 1/2" I wonder if it takes a strap and bolts any one have a # book 63 is 3896838 and the # on the 71 is 3856525 Looks like I need the straps as the yoke is threaded ,see sometimes it pays to talk to yourself or think outloud . __________________ 2001 Silverado K-1500 2005 FXDWG stage3 69 CHEVY Short/Step 327/4L60 373 posi 63 IMPALA 327 Last edited by kaycee; 05-26-2021 at 11:16 PM.

06-02-2021, 01:06 PM	#4
Mike_The_Grad Senior Member Join Date: Oct 2013 Location: Santa Paula, CA Posts: 582	Re: Drive shaft ujoint straps I have a 1972 c10 with 12 bolt rearend. My pinion yoke takes the u joint straps. It took me about 10 years to find out where to get them. And I'm not joking. I found a set on summit. Yukon gear makes them but they want $40+s&h. Which is ridiculous. One day I was explaining this to a friend of mine and he suggested that I try the local napa store. Not feeling to confident about it I went in asked the counter guy and he knew exactly what I was looking for.(he owns a 72 c10 swb.) Sure enough he had them in stock. For about $10. I was expecting at least $20based off the ones I seen on summit. Try the local napa. I will try and find that box or at least a part number if it helps. __________________ 1972 C/10 LWB - Mine 1964 C/10 LWB - My Dad's Instagram: Mike_The_Grad

06-02-2021, 05:55 PM	#5
kaycee Registered User Join Date: Jan 2000 Location: Wyoming USA Posts: 2,445	Re: Drive shaft ujoint straps Yeah I found out they needed straps allso ,went to NAPA and they had them in stock around $6.00 told the parts guy to look up 73 C-10 and booom there it was __________________ 2001 Silverado K-1500 2005 FXDWG stage3 69 CHEVY Short/Step 327/4L60 373 posi 63 IMPALA 327

06-02-2021, 07:15 PM	#6
Mike_The_Grad Senior Member Join Date: Oct 2013 Location: Santa Paula, CA Posts: 582	Re: Drive shaft ujoint straps Napa part number I have for the u joint straps is: UJ360-10 __________________ 1972 C/10 LWB - Mine 1964 C/10 LWB - My Dad's Instagram: Mike_The_Grad



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.