transmission floorpan cover. - The 1947 - Present Chevrolet & GMC Truck Message Board Network

1971gmcshortbed · 07-15-2003, 02:49 PM

hello all, since i'm on the auto trans swap, do these trucks use 2 different floor pan covers? i may not need the huge one for the auto tranny.

**CPNE** · 07-15-2003, 02:53 PM

If you are talking about the transmission "humps" in the cab floor, yes. The bolt-in high hump was used on all 4x4's, all 4 speeds, and most (if not all) big blocks. The small hump is an integral part of the floor (i.e. not bolted in). So if you have a high hump cab, you don't have an option of reverting to the low-hump without a lot of welding. It's very easy to convert a low hump cab to a high hump however.

Longhorn Man · 07-15-2003, 03:58 PM

And the high hump can be found with no shifter holes...but you have to look for them.

**CPNE** · 07-15-2003, 04:05 PM

which can be had here

1971gmcshortbed · 07-15-2003, 08:23 PM

ok thanks guys, i'm gonna remove the large hump one and have the hole covered. i hope the truck megashifter doesn't sit to high, it's got a taller base and lever i think...

western star · 07-15-2003, 08:40 PM

I just completed converting my high hump to a low hump and it's very easy. Unbolt the high hump. Now I have a parts truck so all I did was cut out the low hump cutting it wider than I needed. If you look at both floors you will see in the low hump there is a line you can follow from the stamping. Once I was close to fitting it I just ground the edges down with a grinder until it fit. Make sure when you cut the low hump out cut extra high under the dash to allow for error. Once you have it sitting where you like line up the holes in your truck where you unbolted the high hump and drill the new holes in the low hump. You may have to use a little extra sealer or insulation at the fire wall but it fits very well.

07-15-2003, 02:49 PM	#1
1971gmcshortbed Registered User Join Date: Jul 2003 Location: Las Cruces, NM Posts: 284	transmission floorpan cover. hello all, since i'm on the auto trans swap, do these trucks use 2 different floor pan covers? i may not need the huge one for the auto tranny. __________________ My build, http://67-72chevytrucks.com/vboard/s...d.php?t=379006

07-15-2003, 02:53 PM	#2
CPNE Resident Curmudgeon Join Date: Dec 1999 Location: NH Posts: 6,664	If you are talking about the transmission "humps" in the cab floor, yes. The bolt-in high hump was used on all 4x4's, all 4 speeds, and most (if not all) big blocks. The small hump is an integral part of the floor (i.e. not bolted in). So if you have a high hump cab, you don't have an option of reverting to the low-hump without a lot of welding. It's very easy to convert a low hump cab to a high hump however. __________________ Currently on or near the homestead: 67 Chevy SWB 2WD stepside 350/3 on tree (Pat's) 67 GMC SWB 2WD Fleet 402/auto (Brian's under construction) 67 Chevy 3/4 ton 2WD 402/auto (Business Hauler) 67 Chevy 1 ton dually 2WD 396/4 speed (Former business hauler, Needs TLC) 68 Chevy 1/2 ton Suburban 2WD 250 six/3 on tree (Brian's Needs TLC) 70 Chevy 3/4 ton 4WD 350/4 speed (Pat's - Disguised as a 68 GMC) 71 Chevy SWB stepside (Crushed by tree - parts donor) 72 Chevy 3/4 ton 4WD (Parts donor) 72 Chevy 3/4 ton 4WD Suburban (Parts Donor) 72 GMC 3/4 ton 4WD 292 six/4 speed (Mine - Disguised as a 67 GMC) 81 GMC 4WD Dually Dump Body 350/4 speed (Business Hauler) 82 Camaro Z/28 355/Super T-10 (Pat's toy) 93 Caprice 9C1 (Brian's Cop Car) 02 Toyota Camry (Reliable but a souless steel and plastic hulk) 2011 2SS RS Camaro M6 Factory Hurst Shifter Maybe I need to sell some of this crap Yet another Bozo with a sawz-all

07-15-2003, 04:05 PM	#4
CPNE Resident Curmudgeon Join Date: Dec 1999 Location: NH Posts: 6,664	which can be had here __________________ Currently on or near the homestead: 67 Chevy SWB 2WD stepside 350/3 on tree (Pat's) 67 GMC SWB 2WD Fleet 402/auto (Brian's under construction) 67 Chevy 3/4 ton 2WD 402/auto (Business Hauler) 67 Chevy 1 ton dually 2WD 396/4 speed (Former business hauler, Needs TLC) 68 Chevy 1/2 ton Suburban 2WD 250 six/3 on tree (Brian's Needs TLC) 70 Chevy 3/4 ton 4WD 350/4 speed (Pat's - Disguised as a 68 GMC) 71 Chevy SWB stepside (Crushed by tree - parts donor) 72 Chevy 3/4 ton 4WD (Parts donor) 72 Chevy 3/4 ton 4WD Suburban (Parts Donor) 72 GMC 3/4 ton 4WD 292 six/4 speed (Mine - Disguised as a 67 GMC) 81 GMC 4WD Dually Dump Body 350/4 speed (Business Hauler) 82 Camaro Z/28 355/Super T-10 (Pat's toy) 93 Caprice 9C1 (Brian's Cop Car) 02 Toyota Camry (Reliable but a souless steel and plastic hulk) 2011 2SS RS Camaro M6 Factory Hurst Shifter Maybe I need to sell some of this crap Yet another Bozo with a sawz-all

07-15-2003, 08:23 PM	#5
1971gmcshortbed Registered User Join Date: Jul 2003 Location: Las Cruces, NM Posts: 284	ok thanks guys, i'm gonna remove the large hump one and have the hole covered. i hope the truck megashifter doesn't sit to high, it's got a taller base and lever i think... __________________ My build, http://67-72chevytrucks.com/vboard/s...d.php?t=379006

07-15-2003, 03:58 PM	#3
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,693	And the high hump can be found with no shifter holes...but you have to look for them.

07-15-2003, 08:40 PM	#6
western star Registered User Join Date: Mar 2003 Location: Victoria BC Canada Posts: 198	I just completed converting my high hump to a low hump and it's very easy. Unbolt the high hump. Now I have a parts truck so all I did was cut out the low hump cutting it wider than I needed. If you look at both floors you will see in the low hump there is a line you can follow from the stamping. Once I was close to fitting it I just ground the edges down with a grinder until it fit. Make sure when you cut the low hump out cut extra high under the dash to allow for error. Once you have it sitting where you like line up the holes in your truck where you unbolted the high hump and drill the new holes in the low hump. You may have to use a little extra sealer or insulation at the fire wall but it fits very well.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.