Does my '64 GMC dash come unbloted? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

ChadMorris · 08-12-2005, 08:11 AM

Title says it all. Is it welded in, or if I take out the windshield, are their screws under the seal. I have looked, but can not tell anything under the dash.

Thanks guys!

rodnok1 · 08-12-2005, 09:29 AM

It is welded in

ChadMorris · 08-12-2005, 01:51 PM

Thanks, that keeps me from taking out the window and going "Where the heck are the screws!!!!!"

Demmit_Hemmit's 65 · 08-12-2005, 05:15 PM

In All These Years Of Trucks The Dash Is Welded In Under The Windshield Rubber..................go Thing You Didn't Take Out The Window Because You'd Gotten A Surprise.............i Replaced My Dash In My 65 Suburban A Few Years Ago And Had To Drill The Pinch Welds Out.........i Believe There Were 25 Or So Of Them..................it Also Was Bolted On Both Sides Under The Dash....................all In All It Wasn't That Bad Of A Job To Do..............................hemmit

08-12-2005, 08:11 AM	#1
ChadMorris Newbie truck Rebuilder! Join Date: Dec 2004 Location: Huntsville, Al Posts: 160	Does my '64 GMC dash come unbloted? Title says it all. Is it welded in, or if I take out the windshield, are their screws under the seal. I have looked, but can not tell anything under the dash. Thanks guys! __________________ "Old Blue" 1964 GMC Fleetside in pieces 350 TPI with 700R4 tranny now installed( well kinda propped in place until the tranny crossmember is bolted in !!!!! 1995 Toyota 4runner , 197,000 miles and going... 2007 Honda Odyssey Van (Wifes car)

08-12-2005, 09:29 AM	#2
rodnok1 Registered User Join Date: Jun 2003 Location: Linden, North Carolina Posts: 617	It is welded in __________________ 64 Panel Rebuild Pics Clutch Replacement and Borg Warner T10 Trans Rebuild 64 Panel 1/2 Ton 350cubes/400hp BorgWarner t-10 3:73 Auburn Posi

08-12-2005, 01:51 PM	#3
ChadMorris Newbie truck Rebuilder! Join Date: Dec 2004 Location: Huntsville, Al Posts: 160	Thanks, that keeps me from taking out the window and going "Where the heck are the screws!!!!!" __________________ "Old Blue" 1964 GMC Fleetside in pieces 350 TPI with 700R4 tranny now installed( well kinda propped in place until the tranny crossmember is bolted in !!!!! 1995 Toyota 4runner , 197,000 miles and going... 2007 Honda Odyssey Van (Wifes car)

08-12-2005, 05:15 PM	#4
Demmit_Hemmit's 65 Senior Member Join Date: Mar 2002 Location: Peru, Indiana Posts: 741	In All These Years Of Trucks The Dash Is Welded In Under The Windshield Rubber..................go Thing You Didn't Take Out The Window Because You'd Gotten A Surprise.............i Replaced My Dash In My 65 Suburban A Few Years Ago And Had To Drill The Pinch Welds Out.........i Believe There Were 25 Or So Of Them..................it Also Was Bolted On Both Sides Under The Dash....................all In All It Wasn't That Bad Of A Job To Do..............................hemmit



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.