454 Question - The 1947 - Present Chevrolet & GMC Truck Message Board Network

cweber · 03-10-2011, 05:22 PM

So a buddy is tearing down his mud bogger and is wanting to sell me his 454. Its stock and runs but has recently develped a knock, so he is going back to his 350. He only wants $75 bucks for the complete motor minus the carb and distributor. My question is how hard and expensive is it to get about 500-600 horse from this motor? It doesnt sound like its that difficult to get 1hp/1ci from what i have seen. Any thoughts or suggestions?

vin63 · 03-10-2011, 07:56 PM

Yes, it is not too difficult to reach 500 bhp from a BBC. But, in your case, I would have the block thoroughly checked. Good luck.

**PGSigns** · 03-10-2011, 10:07 PM

How hard and how expensive it is to 500 or 600 greatly depends on what you are starting with. Getting 500 is a lot easier than 600 out of a 454. Any ideas of what is in the motor he wants to sell you and how much water and dirt has been through it?
Jimmy

djracer · 03-11-2011, 08:48 AM

Try to get the casting numbers off the heads and block. If you can find out if it has a cast or steal crank?

cweber · 03-11-2011, 10:51 AM

I dont think its had any water or dirt in it, but Im sure some could have made its way in. Its just a bone stock from a 70s or 80s truck. I think I may have decided against it. I havnt even put 600 miles on my 350, and have enough trouble keeping the tires stuck to the ground.

dougminton · 03-11-2011, 01:27 PM

Go big block. Always go big block.

cweber · 03-14-2011, 04:16 PM

So I told the guy no and now I have a big block in my shed. The research begins!

03-10-2011, 05:22 PM	#1
cweber Registered User Join Date: Jun 2007 Location: Fay, OK Posts: 69	454 Question So a buddy is tearing down his mud bogger and is wanting to sell me his 454. Its stock and runs but has recently develped a knock, so he is going back to his 350. He only wants $75 bucks for the complete motor minus the carb and distributor. My question is how hard and expensive is it to get about 500-600 horse from this motor? It doesnt sound like its that difficult to get 1hp/1ci from what i have seen. Any thoughts or suggestions?

03-10-2011, 07:56 PM	#2
vin63 It's Better With Nitro Join Date: Apr 2008 Location: Chino Hills, CA Posts: 2,261	Re: 454 Question Yes, it is not too difficult to reach 500 bhp from a BBC. But, in your case, I would have the block thoroughly checked. Good luck. __________________ 1963 C-10: Deluxe-optioned cab, shortbed, fleetside Pontiac 462 ci, Kauffman D-Port alum. heads 4L80E, narrowed sheetmetal Ford 9-inch Tubular front and rear suspension Custom 6-piston front disc and 4-piston rear disc brakes

03-10-2011, 10:07 PM	#3
PGSigns Senior Member Join Date: Jan 2011 Location: Hayes Va Posts: 4,569	Re: 454 Question How hard and how expensive it is to 500 or 600 greatly depends on what you are starting with. Getting 500 is a lot easier than 600 out of a 454. Any ideas of what is in the motor he wants to sell you and how much water and dirt has been through it? Jimmy __________________ 60 to 66 Chevy and GMC window decals http://67-72chevytrucks.com/vboard/s...d.php?t=661131 Good friends, good food and a hotrod what else do you need? 1966 BBW long fleet Daily driver 1965 BBW short fleet Sold and going to a good home 1965 Suburban 2003 3500 Duramax 2005 Ultra Classic

03-11-2011, 08:48 AM	#4
djracer Registered User Join Date: Feb 2001 Location: Wetumpka, Al, U.S. Posts: 8,891	Re: 454 Question Try to get the casting numbers off the heads and block. If you can find out if it has a cast or steal crank? __________________ Kevin Special Thanks to All who have helped on the TRUCK! My Pass Time Show http://s129.photobucket.com/albums/p...Chapter1-0.mp4 So Far my best Times are: Motor only: 6.44 1/8 @ 104.13 10.39 1/4 @ 125.83 Nitrous Times: 5.785 1/8 @ 118.65 with a 1.336 60ft 9.168 1/4 @ 142.58 with a 250 shot dead out of the hole!

03-11-2011, 10:51 AM	#5
cweber Registered User Join Date: Jun 2007 Location: Fay, OK Posts: 69	Re: 454 Question I dont think its had any water or dirt in it, but Im sure some could have made its way in. Its just a bone stock from a 70s or 80s truck. I think I may have decided against it. I havnt even put 600 miles on my 350, and have enough trouble keeping the tires stuck to the ground.

03-11-2011, 01:27 PM	#6
dougminton Registered User Join Date: Mar 2009 Location: norman okahoma Posts: 269	Re: 454 Question Go big block. Always go big block. __________________ The TEAL GMC build thread is HERE 1972 GMC SWB 454 oval ports TH400 fastest 1/4 mile time so far 13.05 @ 104 If you think you have too much horsepower you obviously have a traction problem !

03-14-2011, 04:16 PM	#7
cweber Registered User Join Date: Jun 2007 Location: Fay, OK Posts: 69	Re: 454 Question So I told the guy no and now I have a big block in my shed. The research begins! Last edited by cweber; 03-14-2011 at 04:17 PM.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.