Register or Log In To remove these advertisements. |
|
|
|
Thread Tools | Display Modes |
|
11-17-2022, 04:47 PM | #1 | |
Proud Vet that loves the USA
Join Date: Jun 2016
Location: Beebe, AR
Posts: 458
|
Re: Sandy~~1984 C10 L86/4L80 build
Quote:
We are entertaining options now for sure, but it is def the Holley Terminator system. One option is a cam swap with a smaller fuel pump lobe, but then again we dont know if the Terminator will perform, like its supposed to. Second is pulling the Terminator out and installing a stand alone engine and another stand alone trans harness. Either was whatever we decide will be a pain in the a$$ to do. Jus waiting on some software now.... Bubba |
|
11-17-2022, 10:17 PM | #2 |
Registered User
Join Date: Jul 2005
Location: SK, Canada
Posts: 488
|
Re: Sandy~~1984 C10 L86/4L80 build
Would you use something other than Terminator if you were starting from scratch?
__________________
Evan B. |
11-19-2022, 12:17 PM | #3 |
Proud Vet that loves the USA
Join Date: Jun 2016
Location: Beebe, AR
Posts: 458
|
Re: Sandy~~1984 C10 L86/4L80 build
Yes and no brother. I have used Terminators on quite a few LS swaps and have had zero issues. And I have two builds right now that I will use it.
However if I was to swap an LT engine into something else, I would not use the Terminator. Holley makes some good stuff, but they are missed the mark on this when they put it out for the masses. More to follow I'm sure.... Bubba |
11-19-2022, 02:23 PM | #4 |
Registered User
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 21,915
|
Re: Sandy~~1984 C10 L86/4L80 build
What other options are available for Non stock LT based swaps? Motec?
__________________
67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... Cubic inches is like Indiana Jones with a cheap pistol. |
11-24-2022, 09:48 PM | #5 |
Proud Vet that loves the USA
Join Date: Jun 2016
Location: Beebe, AR
Posts: 458
|
Re: Sandy~~1984 C10 L86/4L80 build
|
11-25-2022, 12:30 AM | #6 |
Registered User
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 21,915
|
Re: Sandy~~1984 C10 L86/4L80 build
I didn't realize others were that indepth w/LT swaps already.
__________________
67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... Cubic inches is like Indiana Jones with a cheap pistol. |
11-19-2022, 09:19 PM | #7 | |
Registered User
Join Date: Jul 2005
Location: SK, Canada
Posts: 488
|
Re: Sandy~~1984 C10 L86/4L80 build
Quote:
__________________
Evan B. |
|
11-25-2022, 05:32 AM | #8 | |
Registered User
Join Date: Feb 2017
Location: Texas
Posts: 45
|
Re: Sandy~~1984 C10 L86/4L80 build
Quote:
|
|
Bookmarks |
|
|