The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1967 - 1972 Chevrolet & GMC Pickups Message Board > 67-72 Chevrolet & GMC Pickups Projects and Builds

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 03-19-2017, 09:46 AM   #1
Surge22
Registered User
 
Surge22's Avatar
 
Join Date: Mar 2017
Location: Woodlawn TN
Posts: 6
Red face Finishing Up a 350 Reuild

I'm almost done with my first-ever engine rebuild & yes it's very exciting. However I cant seem to find info on the tiny finishing touches. For instance, what do I do with all these extra holes in the block?
There should be a plug for the cyl head that doesn't have the temp sender in it, but there's also:
One fine-thread hole at the edge of the intake, under and behind the distributor
And 2 very small holes above the bell housing
I wouldn't be surprised if there are a couple more I haven't noticed.

Thanks in advance!
Surge22 is offline   Reply With Quote
Old 03-19-2017, 10:13 AM   #2
72bowtiestepper
Registered User
 
Join Date: Feb 2013
Location: Northwest NJ
Posts: 684
Re: Finishing Up a 350 Reuild

If you are refering to the threaded hole in the block behind the distributor
(1/8 -27 thread)--that is for your oil pressure sensor or oil pressure line to gauge. Don't start your engine with this hole open....you will have a HUGE oil leak !
72bowtiestepper is offline   Reply With Quote
Old 03-19-2017, 02:10 PM   #3
GR8-68
Senior Member
 
GR8-68's Avatar
 
Join Date: Jun 2009
Location: Belews Creek , NC
Posts: 4,220
Re: Finishing Up a 350 Reuild

Are you referring to these two small holes above bell housing ? (1st pic)

Second picture is where your oil pressure sensor goes, it is actually a 1/4" hole for a sending unit if your running an oil light or use a 1/4" -1/8" reducer if you are running a pressure guage. Like the one I have pictured. Hope this helps.
Attached Images
  
__________________
Larry

It is easily overlooked that what is now called vintage was once brand new.

"Project 68"

paypal.me/ldgrant
GR8-68 is offline   Reply With Quote
Old 03-19-2017, 09:06 PM   #4
Surge22
Registered User
 
Surge22's Avatar
 
Join Date: Mar 2017
Location: Woodlawn TN
Posts: 6
Re: Finishing Up a 350 Reuild

72bowtie & GR8-68, thanks for the quick responses!

Oil pressure sender- now that's slightly important, but I never thought about it, or saw it mentioned anywhere in the rebuild manuals I've got. Looking that up, I see that I've got yet another hole to fill: the alternate mounting above the oil filter.
GR8-68, is that a tube coming from yours? Where is the actual sender mounted? The photos I'm seeing show it right on the engine block, often with an angled fitting.
Yes, those are the 2 bellhousing holes I meant. What are they for?

~W
Surge22 is offline   Reply With Quote
Old 03-19-2017, 09:11 PM   #5
GR8-68
Senior Member
 
GR8-68's Avatar
 
Join Date: Jun 2009
Location: Belews Creek , NC
Posts: 4,220
Re: Finishing Up a 350 Reuild

The hose is actually the oil line to the gauge, some previous owner put a rubber hose over it to protect it. The two holes I have no idea what they are for but they are on all the blocks but do not go all the way through. Something to do with the casting maybe.
__________________
Larry

It is easily overlooked that what is now called vintage was once brand new.

"Project 68"

paypal.me/ldgrant
GR8-68 is offline   Reply With Quote
Old 03-19-2017, 09:12 PM   #6
GR8-68
Senior Member
 
GR8-68's Avatar
 
Join Date: Jun 2009
Location: Belews Creek , NC
Posts: 4,220
Re: Finishing Up a 350 Reuild

That line is for a mechanical guage
__________________
Larry

It is easily overlooked that what is now called vintage was once brand new.

"Project 68"

paypal.me/ldgrant
GR8-68 is offline   Reply With Quote
Old 03-19-2017, 09:14 PM   #7
GR8-68
Senior Member
 
GR8-68's Avatar
 
Join Date: Jun 2009
Location: Belews Creek , NC
Posts: 4,220
Re: Finishing Up a 350 Reuild

If you have a light rather than a gauge you would use this
Attached Images
 
__________________
Larry

It is easily overlooked that what is now called vintage was once brand new.

"Project 68"

paypal.me/ldgrant
GR8-68 is offline   Reply With Quote
Old 03-19-2017, 09:27 PM   #8
68c10airstream
Registered User
 
68c10airstream's Avatar
 
Join Date: Mar 2013
Location: Marquette michigan
Posts: 828
Re: Finishing Up a 350 Reuild

In post #3 with the 2 holes close together, these were used to index and hold spark plug wire holder looms. One hole threaded to hold down the bracket and the other hole was used for the loom indexing notch to fall into to prevent it from moving around. The plug wires run behind each cylinder head and then under the exhaust manifold to then come up and "Y" off to each pair of plugs. The wires ran along side the block down low to stay under the hot exhaust manifolds and near the block to be retained with more loom holders.
68c10airstream is offline   Reply With Quote
Old 03-20-2017, 06:48 AM   #9
GR8-68
Senior Member
 
GR8-68's Avatar
 
Join Date: Jun 2009
Location: Belews Creek , NC
Posts: 4,220
Re: Finishing Up a 350 Reuild

Nice, thanks for that info. Now that you say that it comes back to mind, back in the day I remember taking some of those off
__________________
Larry

It is easily overlooked that what is now called vintage was once brand new.

"Project 68"

paypal.me/ldgrant
GR8-68 is offline   Reply With Quote
Old 03-20-2017, 11:42 AM   #10
72bowtiestepper
Registered User
 
Join Date: Feb 2013
Location: Northwest NJ
Posts: 684
Re: Finishing Up a 350 Reuild

Quote:
Originally Posted by GR8-68 View Post
Are you referring to these two small holes above bell housing ? (1st pic)

Second picture is where your oil pressure sensor goes, it is actually a 1/4" hole for a sending unit if your running an oil light or use a 1/4" -1/8" reducer if you are running a pressure guage. Like the one I have pictured. Hope this helps.
Good pictures....The tapped hole in the block for the oil pressure sensor IS
1/8-27 tapered pipe thread though, not a 1/4" hole.
1/8-27 thread mics up as .390 O.D. 1/4" is .250 O.D.
Trust Me ..I have 40+ yrs. of experience as a machinist.
72bowtiestepper is offline   Reply With Quote
Old 03-20-2017, 01:32 PM   #11
GR8-68
Senior Member
 
GR8-68's Avatar
 
Join Date: Jun 2009
Location: Belews Creek , NC
Posts: 4,220
Re: Finishing Up a 350 Reuild

Quote:
Originally Posted by 72bowtiestepper View Post
Good pictures....The tapped hole in the block for the oil pressure sensor IS
1/8-27 tapered pipe thread though, not a 1/4" hole.
1/8-27 thread mics up as .390 O.D. 1/4" is .250 O.D.
Trust Me ..I have 40+ yrs. of experience as a machinist.
Sorry, you are correct, these can sometimes be confusing
__________________
Larry

It is easily overlooked that what is now called vintage was once brand new.

"Project 68"

paypal.me/ldgrant
GR8-68 is offline   Reply With Quote
Reply

Bookmarks

Tags
350, block, screw holes, vents


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 03:20 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com