The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Paint & Bodywork

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 04-22-2021, 07:44 AM   #1
tinman_local2
Registered User
 
Join Date: Jul 2015
Location: Smithton, Mo.
Posts: 119
Orange peel

Getting close to painting my k20. I've read a lot about how to avoid orange peel, but no real fixes or what exactly causes it. I've heard gun settings, travel speed, and temperature are all causes. My question is, if you get orange peel what do you change? Is it too high pressure, too much volume, too low pressure, travel speed too slow or fast. I've sprayed some single stage paints before with little problems. I've never done BC/CC. Just trying to avoid alot of cutting and buffing. Any tips from the pros would be appreciated.
tinman_local2 is offline   Reply With Quote
Old 04-22-2021, 09:06 AM   #2
mongocanfly
Post Whore
 
mongocanfly's Avatar
 
Join Date: May 2015
Location: Alabama
Posts: 12,875
Re: Orange peel

I had bad op with mine..turned out my gauge was bad and my pressure was to low..
__________________
Mongo...aka Greg

1981 C30 LQ9 NV4500..http://67-72chevytrucks.com/vboard/s...d.php?t=753598
Mongos AD- LS3 TR6060...http://67-72chevytrucks.com/vboard/s...34#post8522334
Columbus..the 1957 IH 4x4...http://67-72chevytrucks.com/vboard/s...63#post8082563
2013 GMC Z71..daily driver
mongocanfly is offline   Reply With Quote
Old 04-30-2021, 08:16 PM   #3
lupo
Registered User
 
Join Date: Aug 2019
Location: usa
Posts: 145
Re: Orange peel

There is 19 different reasons for having orange peel . when you look at a chart it says the pressure is too high, the pressure is too low or too close with the gun . I would suggest painting the backside of a fender or a scrap piece and make your adjustments When you get good flow out THEN PAINT the panels. Sometimes a little extra reducer does the trick
Therefore reducing the amount of cutting and buffing.

Last edited by lupo; 04-30-2021 at 11:07 PM.
lupo is offline   Reply With Quote
Old 05-10-2021, 11:11 PM   #4
Grounded63
Registered User
 
Join Date: Dec 2016
Location: Denver, Colorado
Posts: 26
Re: Orange peel

The most common causes of "orange peel " in modern CC's ( given the gun is set up correctly ) is going to be moving too fast or the gun too far from the surface. If your moving too fast, the clear will go on too thin and dry, and wont flow out. If your too far away, kinda the same thing. Your just billowing clear over the panel and it goes on dry, unless you really slow down. You need to apply the clear to the panel.

If your in a booth with good lighting. You want to look right at where the clear is hitting the panel or slightly behind, and pay attention to what the clear is actually doing. Whether its flowing out, dry, or too thick, rippling behind the gun. You'll also pick up your cap to surface and overlap reference here. Where you are on the panel, what your hoses are doing, how much clear is still in the cup, ect you pick up in peripherals.

Using too fast of a hardener or reducer for shop conditions. Will also not allow the clear to flow out properly.
Grounded63 is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 07:30 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2021, vBulletin Solutions Inc.
Copyright 1997-2020 67-72chevytrucks.com