CA Lots of NP205 New Process 205 Parts

[wesleytucker454]

Awesome! Thank you, Dan!
Posted via Mobile Device

[MAXMAN]

I may be interested in a couple of the link bars shown in this pic. I'm referring to the bar that attaches to the shift rails. I'm in need of the second design bar that was machined for use with a bushing/grommet in the link bar. Attached also is a picture of an nos unit like the one I'm looking for. You can see the machined area in it. Do you have any of this style?

[BLAZERMAN]

I would be interested in a pair of detent springs, poppet balls and plugs. Also I'm looking for an indicator light switch from an 82 to 91 GM or Dodge case.

[66gmcguy]

Hey Dan, for some reason I'm not able to send you a message. Do you have any 27 spline input gears left?

[Getter-Done]

His last time on the board was 02-28-2022.

[ChevyK10Dan]

I had to pull away from hobbies to help my dad deal with some health issues.
I oddly enough just got back into selling parts. In in effort to move more parts I started listing on eBay but checked back here tonight. I renewed my subscription for a month to let everyone know what's going, and get back to the inquiries posted.
Thanks Dan

[ChevyK10Dan]

Originally Posted by BLAZERMAN

I would be interested in a pair of detent springs, poppet balls and plugs. Also I'm looking for an indicator light switch from an 82 to 91 GM or Dodge case.

Hi, sorry for the delay but I sold the only 4 I had that worked on eBay.
They are going to your neck of the woods...

Thanks,
Dan

[ChevyK10Dan]

Originally Posted by 66gmcguy

Hey Dan, for some reason I'm not able to send you a message. Do you have any 27 spline input gears left?

Sorry, I had not renewed my paid subscription (to sell parts) while I was helping my dad deal with health issues, so my inbox was full.

If you are still interested I do have a couple and can sell them cheaper on here than eBay, and use the extra money to support this site.

Let me dig them out tomorrow and I'll get back to you in a PM.

Thanks,
Dan

[ChevyK10Dan]

Originally Posted by MAXMAN

I may be interested in a couple of the link bars shown in this pic. I'm referring to the bar that attaches to the shift rails. I'm in need of the second design bar that was machined for use with a bushing/grommet in the link bar. Attached also is a picture of an nos unit like the one I'm looking for. You can see the machined area in it. Do you have any of this style?

Hi, I believe I have at least one. I'll check tomorrow and send you a PM.

Thanks,
Dan

[BLAZERMAN]

Originally Posted by ChevyK10Dan

Hi, sorry for the delay but I sold the only 4 I had that worked on eBay.
They are going to your neck of the woods...

Thanks,
Dan

Dan, yes in fact they coming to me...Thanks, and I'm sending you a PM

[ChevyK10Dan]

All PM's have been sent/responded to.

I'm continuing to list stuff on eBay, so if anyone needs anything before I list it let me know. Once it's listed I have to pay a fee to remove it from eBay so I can't sell it on here.

Thanks,
Dan

[zach_carver]

Do you have any NP203 shift knobs left? I'm looking for one with the shift pattern on it with the highs on bottom and lows top. Id be interested if so PM me please.

[ChevyK10Dan]

Originally Posted by zach_carver

Do you have any NP203 shift knobs left? I'm looking for one with the shift pattern on it with the highs on bottom and lows top. Id be interested if so PM me please.

Hi, sorry I do not have for the 203, only the 205. I do still have a couple of the aluminum shift pattern plates that go beside the shifter boot under the retaining ring.

Thanks,
Dan

[ChevyK10Dan]

Originally Posted by ChevyK10Dan

Sorry, I had not renewed my paid subscription (to sell parts) while I was helping my dad deal with health issues, so my inbox was full.

If you are still interested I do have a couple and can sell them cheaper on here than eBay, and use the extra money to support this site.

Let me dig them out tomorrow and I'll get back to you in a PM.

Thanks,
Dan

Here is a 27 spline input gear I have. As mentioned it has good teeth, but some pitting on the bearing surface.

Thanks,
Dan

[1966 K10]

Interested in the divorced TC, have the input, retainer etc to go with it? 1350 or 1450? And the usual deal killer, cost to ship to 98022.

Thanks

[ChevyK10Dan]

Originally Posted by 1966 K10

Interested in the divorced TC, have the input, retainer etc to go with it? 1350 or 1450? And the usual deal killer, cost to ship to 98022.

Thanks

I currently have the Bare Dodge divorced case with the correct 32 spline input shaft and input bearing retainer listed on eBay. I had to go high on the list price ($595 plus shipping), the way eBay is nowadays, I have to pay a final fee on the entire total (sell price, shipping, and sales tax). I can go cheaper on here but I don't know what the fee to end the listing is.

I have the Bare divorced International case that's not listed on eBay yet, that I can also sell with the correct 32 spline input shaft and bearing retainer if you don't have a preference. They are both passenger side drop, the mounting bolt location is the main difference.

I have a complete Dodge divorced 205 that I've been saving for a project, but would consider selling it. Shipping would probably be the deal breaker though. The bare cases are $75-$175 to ship in the lower 48, the complete case would have to go freight and I don't have an account like a lot of people so it's not going to be cheap.

These divorced cases came with the Dodge style yokes that use the straps not u-bolts and I don't think they are as strong. I'll have to check what size they are but probably 1310, maybe 1350.

I'll work on the shipping quote, but it will only be a ballpark without the full address. You can also check the shipping price on the eBay listing to get an exact number.

I'll send you a PM after work tomorrow.

Thanks,
Dan

[ChevyK10Dan]

PM's sent

Dan