|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
04-11-2022, 01:43 PM
|
#1 |
|
Registered User
Join Date: Jul 2015
Location: Hudson
Posts: 43
|
Front Crossmember Swap
Swapping 4wd k5 to 2wd.
Full Parts 88 suburban, 2wd. Moved front crossmember over, and got it lined up in the rear bottom hole (where the k5 brake line used to go through) wheels look centered also. The engine perch when set on the bottom of the subframe is about 1inch too high on the frame rails? What should I be doing here? Going to be dropping in a 5.3/4l60e. Have the square body swap mounts and new clamshells. Any help appreciated. |
|
|
|
04-11-2022, 01:47 PM
|
#2 |
|
Registered User
Join Date: Jul 2015
Location: Hudson
Posts: 43
|
Re: Front Crossmember Swap
Pics Attached.
|
|
|
|
|
04-11-2022, 02:30 PM
|
#3 |
|
Carpe manana
  
Join Date: Dec 2010
Location: Eau Claire, WI
Posts: 12,280
|
Re: Front Crossmember Swap
Greetings from Eau Claire. I've moved this thread to the general Blazer/Jimmy board for more eye balls.
__________________
1972 K5 CST Highlander Blazer: http://67-72chevytrucks.com/vboard/s...d.php?t=708547 1972 K20 Cheyenne Super: http://67-72chevytrucks.com/vboard/s...d.php?t=528308  Members met: ORANGBLAZ, 2003 silverado, MikeCofield, BB72CHEVKT, Duncan&Son, Sameyrasmea72, THENEWMEXICAN, HotRod C/10, brianthelion02, Sport/Truck, ryanroo, michael bustamante, Dirt's72, Already Gone, WestButteTruck, 57taskforce, Moreyel, painterljp, AASmedic, SoCoC10, Lumaestas, carbuff382, Chevyland
|
|
|
|
|
04-11-2022, 02:41 PM
|
#4 |
|
Registered User
Join Date: Jul 2015
Location: Hudson
Posts: 43
|
Re: Front Crossmember Swap
Thank you, Thought "project problems" Appreciate it.
|
|
|
|
|
04-12-2022, 11:06 AM
|
#5 |
|
Senior Member
 
Join Date: Jun 2002
Location: Murray, Kentucky
Posts: 3,364
|
Re: Front Crossmember Swap
Contact livrat, he has done it many times.
https://67-72chevytrucks.com/vboard/member.php?u=1049 Good luck, Rg
__________________
Roger '68 Short step - https://67-72chevytrucks.com/vboard/...d.php?t=849675 '69 ('70?) 2wd Blazer '70 GMC Jimmy 2wd |
|
|
|
04-12-2022, 01:03 PM
|
#6 |
|
Registered User
Join Date: Jul 2015
Location: Hudson
Posts: 43
|
Re: Front Crossmember Swap
I test fit the 5.3 I'm just going to cut them down and weld some plate across the top for more support. The height doesn't seem to be necessary for anything, except the taller frame rails from the 88. Wheels are centered, and motor is sitting in a decent spot.
Small problems, small solutions, tons of work time. |
|
|
|
|
| Bookmarks |
|
|
Linear Mode
