|
06-15-2002, 03:08 PM
|
#1 |
|
Livin' it up.
 
Join Date: Nov 2001
Location: Richland, MI
Posts: 2,212
|
Adjusting doors
Any tips for this i couldnt see what tools would really fit in there to get at it with the door on and the outer fender on too. Any suggestions please?
__________________
-Greg; Sold the 69 C20. It's off to a better home with more love! Now onto the 86 CUCV M1009; K5 blazer with 6.2L diesel, corp 10 bolt axles, Detroit locker in the rear, trutrac front, 3.73 gears, 35" tires. 
|
|
|
|
06-15-2002, 07:34 PM
|
#2 |
|
Wiseass secured himself a BAN
Join Date: Nov 2000
Location: MOON!!!
Posts: 2,282
|
I have found that ratchet gear wrenches work really well for adjusting the doors. Sears sells them.
Ben |
|
|
|
|
06-15-2002, 09:08 PM
|
#3 |
|
aka Crusher, Crushergmc
Join Date: Mar 2000
Location: Oregon
Posts: 1,834
|
That's what I was going to say, I just couldn't put a name to them.
__________________
"KEEP IT DOWN!" 70 Jimmy 454 2wd 56 GMC Big Window "It's funny till someone gets hurt, then it's freakin' hilarious" |
|
|
|
|
06-15-2002, 09:16 PM
|
#4 |
|
Registered User
Join Date: May 2002
Location: lexington,South Carolina
Posts: 158
|
There is also a special Boxed in wrench that is shaped like a "S".
__________________
69-C10 LWB 71- fleetside shortbed It's a shame stupidity isn't painful Never play leapfrog with a unicorn |
|
|
|
|
06-17-2002, 01:33 PM
|
#5 |
|
Registered User
Join Date: Mar 2002
Location: Dallas, TX
Posts: 555
|
Sears sells a tool called an Obstruction Wrench that is "C" shaped 9/16 and 5/8 box end. I have used this and it works pretty well. Cost about $16.
__________________
1968 GMC 305 V6 3/4 4x4 Stepside 06 Corvette Daily Driver Dallas TX |
|
|
|
|
06-17-2002, 01:52 PM
|
#6 |
|
Registered User
Join Date: Feb 2000
Location: Georgetown, KY, USA
Posts: 631
|
Well NO Doubt about it, it is a Bi#ch to do. But I used a box/open wrench. The S- shaped wrench should work good. I found that if you leave the bolts just loose enough to hit the door with your hand, you can get it where it belongs then tighten it down.
Hope this helps! Good Luck! |
|
|
|
|
06-17-2002, 02:21 PM
|
#7 |
|
Livin' it up.
Join Date: Nov 2001
Location: Richland, MI
Posts: 2,212
|
Thanks fellas, i'm gonna try it as soon as i get it back from the paint shop...
__________________
-Greg; Sold the 69 C20. It's off to a better home with more love! Now onto the 86 CUCV M1009; K5 blazer with 6.2L diesel, corp 10 bolt axles, Detroit locker in the rear, trutrac front, 3.73 gears, 35" tires.
|
|
|
|
 |
| Bookmarks |
|
|
Linear Mode
