Photos of your Floor Shifters! - The 1947 - Present Chevrolet & GMC Truck Message Board Network

smoknbarrels · 02-12-2007, 12:04 PM

I joust bought a borg-w 4 speed for my truck, its got a nice hurst shifter, but i don't know if the bench will be in the way, the handle is not that long, it was in a '80 camaro.. perhaps it won't reach.

I wanna see how long of shifters you guys use, perhaps i may need a new one..?

Willy Prost · 02-12-2007, 11:51 PM

I had a 3 speed floor shifter with the Hurst 4331 shifter handle. 6 cylinder mounting position. The handle just cleared the bench.

The 6900 handle is 3 inches shorter.

Now that I have the Tremec TKO 5 speed, the 6900 handle fits better because the shifter is on top of the transmission instead of on the side like the 3 speed.

Below is a picture of the two. Sorry I don't have a picture of them installed on the truck with the 3 speed.

smoknbarrels · 02-13-2007, 01:42 AM

Thanks! that is an awesome photo and the info I needed, mine is the same as the shorter one, but has a side bend in it.. obviously it will be too short.

nice work.

fastwillie 696969 · 02-13-2007, 03:42 AM

you will need the competiton /plus shifter4 spd to make clearance over the bench http://www.jegs.com/webapp/wcs/store...49299_-1_10523

**special-K** · 02-13-2007, 07:35 AM

When I put a "His & Hers" Hurst shifter in my`71 Blazer I bought a taller shifter.I know back then Hurst had a couple pages of levers in various configurations.I had it to where I could rest my arm along my leg on the edge of my seat and the handle was right there where my hand was.That`s the one thing I always remember about that rig.I could get in a mud-pit,steer with my left and grab gears with my right.I got another lever for my transfer case.I cut the factory lever to below the floor and welded the Hurst lever.It came up just to the right of the tranny shifter.So,I could kick it in and out of 4wd and grab gears w/o reaching,so I could do 2wd powerslides,then throw it into 4wd and blast straight out of my slide.(why did I every sell that thing?)

70c10 · 02-13-2007, 08:08 AM

This angle is not very good but here's a pic of my B&M Megashifter. The truck version is a little taller than this and better for a bench though.

Willy Prost · 02-13-2007, 08:54 AM

Yes, The Hurst catalog still has 3 pages of shifter handles (I think pages 47-49 inclusive). You can look it up online out of the Hurst master catalog (dial-up connections be warned, the master catalog takes a long time to download).

JAKES 68GMC · 02-13-2007, 05:17 PM

ttt

02-12-2007, 12:04 PM	#1
smoknbarrels Registered Mail Join Date: Jun 2006 Location: Alberta, Canada Posts: 513	Photos of your Floor Shifters! I joust bought a borg-w 4 speed for my truck, its got a nice hurst shifter, but i don't know if the bench will be in the way, the handle is not that long, it was in a '80 camaro.. perhaps it won't reach. I wanna see how long of shifters you guys use, perhaps i may need a new one..? __________________ '67 chev 496, lwb to swb, bagged - pro street project

02-12-2007, 11:51 PM	#2
Willy Prost Senior Member Join Date: Jan 2000 Location: Arlington, VA Posts: 398	Re: Photos of your Floor Shifters! I had a 3 speed floor shifter with the Hurst 4331 shifter handle. 6 cylinder mounting position. The handle just cleared the bench. The 6900 handle is 3 inches shorter. Now that I have the Tremec TKO 5 speed, the 6900 handle fits better because the shifter is on top of the transmission instead of on the side like the 3 speed. Below is a picture of the two. Sorry I don't have a picture of them installed on the truck with the 3 speed. Attached Images

02-13-2007, 01:42 AM	#3
smoknbarrels Registered Mail Join Date: Jun 2006 Location: Alberta, Canada Posts: 513	Re: Photos of your Floor Shifters! Thanks! that is an awesome photo and the info I needed, mine is the same as the shorter one, but has a side bend in it.. obviously it will be too short. nice work. __________________ '67 chev 496, lwb to swb, bagged - pro street project

02-13-2007, 03:42 AM	#4
fastwillie 696969 ~Rest In Peace~ Join Date: May 2005 Location: CALIFORNIA NOR CAL Posts: 9,707	Re: Photos of your Floor Shifters! you will need the competiton /plus shifter4 spd to make clearance over the bench http://www.jegs.com/webapp/wcs/store...49299_-1_10523 __________________ is it fast ? it has a lighting bolt donut? B___H please, I can remove 90% of your so called "beauty" with a kleenex

02-13-2007, 07:35 AM	#5
special-K Special Order Join Date: Nov 2004 Location: Mt Airy, MD Posts: 85,862	Re: Photos of your Floor Shifters! When I put a "His & Hers" Hurst shifter in my`71 Blazer I bought a taller shifter.I know back then Hurst had a couple pages of levers in various configurations.I had it to where I could rest my arm along my leg on the edge of my seat and the handle was right there where my hand was.That`s the one thing I always remember about that rig.I could get in a mud-pit,steer with my left and grab gears with my right.I got another lever for my transfer case.I cut the factory lever to below the floor and welded the Hurst lever.It came up just to the right of the tranny shifter.So,I could kick it in and out of 4wd and grab gears w/o reaching,so I could do 2wd powerslides,then throw it into 4wd and blast straight out of my slide.(why did I every sell that thing?) __________________ "BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~

02-13-2007, 08:08 AM	#6
70c10 67-72 Addict! Join Date: Feb 2002 Location: The TAX State! Posts: 7,857	Re: Photos of your Floor Shifters! This angle is not very good but here's a pic of my B&M Megashifter. The truck version is a little taller than this and better for a bench though. Attached Images __________________ Jim 1970 C/10 Fleetside w/Ghost Flames Lowered 4.5" front and 4" rear (Raked) 355/350 Turbo w/shift kit 10" Redneck Performance Verter w/2500 stall Hooker Super Comps part#2808-1 Performer RPM Air-Gap 12 Bolt w/3:73 gears- Eaton Posi Comp Cams XE262 with 1.6 Crane Energizers, Road Demon 625 and Brodix IK 180 heads

02-13-2007, 08:54 AM	#7
Willy Prost Senior Member Join Date: Jan 2000 Location: Arlington, VA Posts: 398	Re: Photos of your Floor Shifters! Yes, The Hurst catalog still has 3 pages of shifter handles (I think pages 47-49 inclusive). You can look it up online out of the Hurst master catalog (dial-up connections be warned, the master catalog takes a long time to download).

02-13-2007, 05:17 PM	#8
JAKES 68GMC Aluminum slot wheels rule... Join Date: Jan 2006 Location: Maine Posts: 6,212	Re: Photos of your Floor Shifters! ttt



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.