Register or Log In To remove these advertisements. |
|
|
|
Thread Tools | Display Modes |
|
07-20-2010, 07:38 AM | #1 |
Registered User
Join Date: Jun 2010
Location: Caledonia Ohio
Posts: 49
|
Re: My T-5 swap all done but got bad trany
Ya sorry I menT input shaft. Just woke up and rePlied lol. No I did not use a step ring where can I get one at? The only time I had trouble geting it in gear was the first start up after that never a problem shifting. I have origa bell in my truck. Let me no about the step ring would like to have one thanx.
|
07-20-2010, 10:40 AM | #2 | |
The Older Generation
Join Date: Aug 2006
Location: Montezuma, Iowa
Posts: 25,373
|
Re: My T-5 swap all done but got bad trany
Quote:
Not to step on raycows toes but I got mine here: http://dennymac.com/mod.php?mod=user...103&page_id=54 Some good info on the site also... I spoke to a nice lady on the phone and the ring was $28.00 shipped. That is the best price I could find anywhere.. LockDoc
__________________
Leon Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles (My Dually Pickup Project Thread) http://67-72chevytrucks.com/vboard/s...d.php?t=829820 - Last edited by LockDoc; 07-20-2010 at 10:45 AM. |
|
07-20-2010, 11:14 AM | #3 | |
Registered User
Join Date: Mar 2003
Location: San Francisco, CA USA
Posts: 2,454
|
Re: My T-5 swap all done but got bad trany
Quote:
Ray |
|
07-20-2010, 11:22 AM | #4 |
Registered User
Join Date: Jun 2010
Location: Caledonia Ohio
Posts: 49
|
Re: My T-5 swap all done but got bad trany
Thanks I just goT it ordered should be hear thursday. I Hope!
|
07-20-2010, 11:36 AM | #5 |
Registered User
Join Date: Mar 2003
Location: San Francisco, CA USA
Posts: 2,454
|
Re: My T-5 swap all done but got bad trany
|
07-20-2010, 12:06 PM | #6 |
Registered User
Join Date: Jun 2010
Location: Caledonia Ohio
Posts: 49
|
Re: My T-5 swap all done but got bad trany
What dose the test entail?
|
07-20-2010, 12:51 PM | #7 |
Registered User
Join Date: Mar 2003
Location: San Francisco, CA USA
Posts: 2,454
|
Re: My T-5 swap all done but got bad trany
Well you would need to bolt the transmission to the bellhousing, but not install the driveshaft. Then have a helper get inside the car, put the transmission in 4th gear, and hold down the clutch pedal. Go underneath the car and try to turn the output shaft. If the shaft doesn't turn easily, that means you have a problem.
I also recommend that you try this same test with the transmission that is installed in there now before you remove it. You can do the test with the driveshaft installed if you get the rear wheels off the ground. Ray |
07-20-2010, 11:12 AM | #8 | |
Registered User
Join Date: Mar 2003
Location: San Francisco, CA USA
Posts: 2,454
|
Re: My T-5 swap all done but got bad trany
Quote:
http://dennymac.com/mod.php?mod=user...103&page_id=54 I have not purchased from them yet, but they have the lowest price for the ring I have seen so far. Ray |
|
Bookmarks |
|
|