|
05-13-2014, 03:50 PM
|
#1 |
|
Registered User
Join Date: Feb 2012
Location: Mission Viejo, CA
Posts: 1,856
|
jack stand dolly
knocked one of these together last week. Need to paint it electric orange so I dont go sliding across the shop.
damn casters aint cheap. They should hold 1200 lbs per stand. assuming my welds hold    the next 3 I'm going to move the wheels out more and trim off the part of the plate that will then stick out. Im not to worried about it but Id like a slightly wider wheelbase. home depot casters where about $6 each x16. 2 4' angle iron and 2 4' square stock. Cost around $150 total. Should support over 4000lbs which willmove any car i have around the show without to much trouble. |
|
|
|
05-13-2014, 04:44 PM
|
#2 |
|
Registered User
Join Date: Jul 2009
Location: San Jose Ca
Posts: 2,871
|
Re: jack stand dolly
Not a bad idea but would buying them at harbor freight be about the same price without the work?
http://www.harborfreight.com/2-piece...ies-67511.html
__________________
David Used parts build: http://67-72chevytrucks.com/vboard/s...d.php?t=638991 My brother's Nova: http://www.67-72chevytrucks.com/vboa...d.php?t=727985 Rear suspension rework: http://www.67-72chevytrucks.com/vboa...d.php?t=750557 Instagram: myfabguy |
|
|
|
|
05-13-2014, 04:48 PM
|
#3 |
|
Registered User
Join Date: Feb 2012
Location: Mission Viejo, CA
Posts: 1,856
|
Re: jack stand dolly
well yea but those dont work so well when you have no wheels and tires
|
|
|
|
|
05-13-2014, 04:49 PM
|
#4 |
|
Registered User
Join Date: Jul 2009
Location: San Jose Ca
Posts: 2,871
|
Re: jack stand dolly
Good point!
__________________
David Used parts build: http://67-72chevytrucks.com/vboard/s...d.php?t=638991 My brother's Nova: http://www.67-72chevytrucks.com/vboa...d.php?t=727985 Rear suspension rework: http://www.67-72chevytrucks.com/vboa...d.php?t=750557 Instagram: myfabguy |
|
|
|
|
05-13-2014, 04:53 PM
|
#5 |
|
Registered User
Join Date: Feb 2012
Location: Mission Viejo, CA
Posts: 1,856
|
Re: jack stand dolly
heres my previous incarnation: they creak and groan with the rear end so I knew I needed something better for the frame buildup and future use.
|
|
|
|
|
05-14-2014, 04:11 PM
|
#6 |
|
2WD Jimmy
 
Join Date: Mar 2005
Location: Davis County, Utah
Posts: 2,563
|
Re: jack stand dolly
Be Very Very careful. Looks like a potential tip hazard to me. Just dont want to see you injured.
|
|
|
|
|
05-14-2014, 04:45 PM
|
#7 |
|
Registered User
Join Date: Feb 2012
Location: Mission Viejo, CA
Posts: 1,856
|
Re: jack stand dolly
Yea me either. The next 3 I build im going to put the wheels more outboard.
|
|
|
|
|
05-17-2014, 09:09 AM
|
#8 |
|
Registered User
Join Date: Feb 2012
Location: Mission Viejo, CA
Posts: 1,856
|
Re: jack stand dolly
pffft. well i can admit to being wrong... I now see why nobody sells jack stand dollys. Lawsuit waiting to happen.
I made 3 more with the wheels more outboard but the stand the same size as the jack stand base.  even like this I had one tip over under my frame when pushing it around when the wheel caught on a piece of trash. The only way I think to make this work would be to weld the jack stand to the dolly and make the dolly 2sqft at least. next time... |
|
|
|
|
05-17-2014, 11:57 PM
|
#9 |
|
Registered User
Join Date: Jul 2010
Location: Mesa, AZ
Posts: 513
|
Re: jack stand dolly
The thought is in the right place. I saw this product on Jay Leno's garage youtube channel. Pricey, but maybe you can reverse engineer it.
http://www.ezvjack.com/
__________________
JB from AZ 1969 Chevy Sub K10 1957 Chevy 3200 1962 VW Beetle 1957 Willys CJ5 
|
|
|
|
 |
| Bookmarks |
|
|
Linear Mode
