factory looking rear discs... - The 1947 - Present Chevrolet & GMC Truck Message Board Network

bagged91 · 01-16-2007, 04:54 PM

I picked up a rear disc setup from a 79' Caddy deville the other day at the u-pull-it yard for $35. Got both backing plates, rotors, calipers & e-brake cables along with the proportioning valve. I had the axles on turned down so the caddy rotors would go on, cost= $40 for both axles... The caddy rear has the small bolt pattern backingplate flange with the staggered bolt holes and smaller center hole whereas the truck backing plate bolts are wider spaced and has a big hole for the axle tube. I took the truck backing plate and cut the center out cut the center from the disc backing plate. I then welded the truck center into the disc center & after a little cleaning up, it bolted on... It looks like I will need to use 2 drivers side caddy e brake cables to make it work.

bagged91 · 01-16-2007, 05:04 PM

Some pics...

bagged91 · 01-16-2007, 05:11 PM

and more... New rotors & calipers will be used when I install on the rear in my truck

ghetto_superman · 01-16-2007, 05:15 PM

very nice!

68shortfleet · 01-16-2007, 05:22 PM

Very cool, i always thought that the caddy stuff just bolted straight on without these mods though? Might it bolt to the 73-87 rearend? Make sure to hook up and use your parking brake, thats what keep this design caliper adjusted properly. If not done they seem to start leaking around the adjuster arm on the back of the caliper.

Jason

AesC10s · 01-16-2007, 06:07 PM

Hell yea good job man!!!

Longhorn Man · 01-16-2007, 08:45 PM

don't forget to set the e-brake from time to time too, otherwise they won't agjust properly

bagged91 · 01-17-2007, 03:32 PM

Thanks

Bob Moore · 01-17-2007, 05:09 PM

What model is the Deville? I have a set-up from the Caddy 77-79 rear wheel drive like the Chev Caprice/Pontiac Bonneville etc. I think it is called the Seville? Was the Deville a FRONT wheel drive?

Thanks - Bob

1969k10stepside · 01-17-2007, 08:15 PM

Good job!

bagged91 · 01-19-2007, 12:28 PM

The Seville is the "midsize" RWD caddy... The Deville is the ocean liner bodystyle, RWD...

Bob Moore · 01-19-2007, 06:01 PM

Thanks - Bagged91

a1953mdl · 01-19-2007, 09:29 PM

Would you give more details on the fitting the rotors on the axles, please. Do the rotors slip on the studs and flange of the factory pickup axle? Any pics would be appreciated.
Thanks for this great thread.
Lee

Bob Moore · 01-20-2007, 12:34 AM

Bagged91 - one more question. The Seville has one caliper in front of the axle and one to the rear. How about the DeVille? Are they both to to the rear?(I hope)

Thanks again - Bob

bagged91 · 01-22-2007, 07:33 PM

Lee, I had to have the outer flange of the axle turned down at a machine shop so that the inside of the caddy rotor would clear it. Now it slips on like the factory drum did...

Bob, the Deville is setup the same as the Seville... I assume that was a GM cost cutting measure so they only had to use one backing plate. I may mess around a little and see if I can make it "symmetrical" when I mod the other backing plate... Defininitely would look better....

01-16-2007, 04:54 PM	#1
bagged91 Out draggin' Join Date: Jan 2004 Location: Pitman,NJ Posts: 1,574	factory looking rear discs... I picked up a rear disc setup from a 79' Caddy deville the other day at the u-pull-it yard for $35. Got both backing plates, rotors, calipers & e-brake cables along with the proportioning valve. I had the axles on turned down so the caddy rotors would go on, cost= $40 for both axles... The caddy rear has the small bolt pattern backingplate flange with the staggered bolt holes and smaller center hole whereas the truck backing plate bolts are wider spaced and has a big hole for the axle tube. I took the truck backing plate and cut the center out cut the center from the disc backing plate. I then welded the truck center into the disc center & after a little cleaning up, it bolted on... It looks like I will need to use 2 drivers side caddy e brake cables to make it work. __________________ 91 GMC Xcab LB-Bags/bd/caddy clip SOLD 72 C10 Cheyenne Super LWB SOLD 92 GMC K1500 Burb 72 C10 Burb (ex. Cheesewagon)SOLD 72 C20 Burb parts truck 71 C10 Burb "project"

01-16-2007, 05:04 PM	#2
bagged91 Out draggin' Join Date: Jan 2004 Location: Pitman,NJ Posts: 1,574	Re: factory looking rear discs... Some pics... Attached Images __________________ 91 GMC Xcab LB-Bags/bd/caddy clip SOLD 72 C10 Cheyenne Super LWB SOLD 92 GMC K1500 Burb 72 C10 Burb (ex. Cheesewagon)SOLD 72 C20 Burb parts truck 71 C10 Burb "project"

01-16-2007, 05:11 PM	#3
bagged91 Out draggin' Join Date: Jan 2004 Location: Pitman,NJ Posts: 1,574	Re: factory looking rear discs... and more... New rotors & calipers will be used when I install on the rear in my truck Attached Images __________________ 91 GMC Xcab LB-Bags/bd/caddy clip SOLD 72 C10 Cheyenne Super LWB SOLD 92 GMC K1500 Burb 72 C10 Burb (ex. Cheesewagon)SOLD 72 C20 Burb parts truck 71 C10 Burb "project"

01-16-2007, 05:15 PM	#4
ghetto_superman Registered User Join Date: Sep 2006 Location: Omaha, NE Posts: 1,982	Re: factory looking rear discs... very nice! __________________ -1947 3100 -1968 C10 -1970 K20

01-16-2007, 05:22 PM	#5
68shortfleet Registered User Join Date: Oct 2006 Location: Dundee, Oregon Posts: 311	Re: factory looking rear discs... Very cool, i always thought that the caddy stuff just bolted straight on without these mods though? Might it bolt to the 73-87 rearend? Make sure to hook up and use your parking brake, thats what keep this design caliper adjusted properly. If not done they seem to start leaking around the adjuster arm on the back of the caliper. Jason

01-16-2007, 06:07 PM	#6
AesC10s Chevy truck addict Join Date: Apr 2005 Location: Thornton Colorado Posts: 825	Re: factory looking rear discs... Hell yea good job man!!!

01-16-2007, 08:45 PM	#7
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,693	Re: factory looking rear discs... don't forget to set the e-brake from time to time too, otherwise they won't agjust properly

01-17-2007, 03:32 PM	#8
bagged91 Out draggin' Join Date: Jan 2004 Location: Pitman,NJ Posts: 1,574	Re: factory looking rear discs... Thanks __________________ 91 GMC Xcab LB-Bags/bd/caddy clip SOLD 72 C10 Cheyenne Super LWB SOLD 92 GMC K1500 Burb 72 C10 Burb (ex. Cheesewagon)SOLD 72 C20 Burb parts truck 71 C10 Burb "project"

01-17-2007, 05:09 PM	#9
Bob Moore Registered User Join Date: Feb 2004 Location: Tacoma WA Posts: 1,365	Re: factory looking rear discs... What model is the Deville? I have a set-up from the Caddy 77-79 rear wheel drive like the Chev Caprice/Pontiac Bonneville etc. I think it is called the Seville? Was the Deville a FRONT wheel drive? Thanks - Bob __________________ 67 C-20 LWB, tilt, speed alert, vac, 454, T400 67 C-10 SWB, factory air with more to follow

01-17-2007, 08:15 PM	#10
1969k10stepside Registered User Join Date: Mar 2006 Location: USA Posts: 21,020	Re: factory looking rear discs... Good job!

01-19-2007, 12:28 PM	#11
bagged91 Out draggin' Join Date: Jan 2004 Location: Pitman,NJ Posts: 1,574	Re: factory looking rear discs... The Seville is the "midsize" RWD caddy... The Deville is the ocean liner bodystyle, RWD... __________________ 91 GMC Xcab LB-Bags/bd/caddy clip SOLD 72 C10 Cheyenne Super LWB SOLD 92 GMC K1500 Burb 72 C10 Burb (ex. Cheesewagon)SOLD 72 C20 Burb parts truck 71 C10 Burb "project"

01-19-2007, 06:01 PM	#12
Bob Moore Registered User Join Date: Feb 2004 Location: Tacoma WA Posts: 1,365	Re: factory looking rear discs... Thanks - Bagged91 __________________ 67 C-20 LWB, tilt, speed alert, vac, 454, T400 67 C-10 SWB, factory air with more to follow

01-19-2007, 09:29 PM	#13
a1953mdl Rusty but Trusty Join Date: Jan 2007 Location: Texas Posts: 228	Re: factory looking rear discs... Would you give more details on the fitting the rotors on the axles, please. Do the rotors slip on the studs and flange of the factory pickup axle? Any pics would be appreciated. Thanks for this great thread. Lee

01-20-2007, 12:34 AM	#14
Bob Moore Registered User Join Date: Feb 2004 Location: Tacoma WA Posts: 1,365	Re: factory looking rear discs... Bagged91 - one more question. The Seville has one caliper in front of the axle and one to the rear. How about the DeVille? Are they both to to the rear?(I hope) Thanks again - Bob __________________ 67 C-20 LWB, tilt, speed alert, vac, 454, T400 67 C-10 SWB, factory air with more to follow

01-22-2007, 07:33 PM	#15
bagged91 Out draggin' Join Date: Jan 2004 Location: Pitman,NJ Posts: 1,574	Re: factory looking rear discs... Lee, I had to have the outer flange of the axle turned down at a machine shop so that the inside of the caddy rotor would clear it. Now it slips on like the factory drum did... Bob, the Deville is setup the same as the Seville... I assume that was a GM cost cutting measure so they only had to use one backing plate. I may mess around a little and see if I can make it "symmetrical" when I mod the other backing plate... Defininitely would look better.... __________________ 91 GMC Xcab LB-Bags/bd/caddy clip SOLD 72 C10 Cheyenne Super LWB SOLD 92 GMC K1500 Burb 72 C10 Burb (ex. Cheesewagon)SOLD 72 C20 Burb parts truck 71 C10 Burb "project"



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.