VA Parting out 70 Blazer

[clamcake]

PM sent. Thank you Zicc1835!

[briank]

Any news?

[72ghost]

Do you have the rear bench seat brackets?

[Rust Buster]

Originally Posted by briank

Interested in transfer case cover for the dana 20 as well as the trans hump cover or just the trim ring for it I see pictured. Also for the screws on the door near the vent windows. Do you have the original speaker anywhere?

Sorry, the cover is gone, don't know where, but those pics were taken last year and in the move I can't find it. Will let you know if I do. I will check on the screws for door vent window this weekend as well as the speaker. It was a long trip back to VA and I'm headed out on a military trip this week.
Thanks

[Rust Buster]

Originally Posted by HarleyT

I need a fuel filler cover if you have it
Thanks

Sorry, I know that is gone. I'm sure the tank is full of water.

[Rust Buster]

Originally Posted by pwdcougar

How is the grill?

The grille has a large crack down the middle.

[Rust Buster]

I'm sorry to leave you all hanging, I got crazy busy over the holiday and it was a long trip back to VA last night. If I haven't already PM'd you, I promise I will this weekend. I only had time today to unhitch the trailer and pack as I'm headed out on a military trip this week. Hoping to get it in my shop this weekend and can write you all back on the status of the parts you have asked about. I also need to figure out what I need to keep for my project.
Sorry for the wait!
-Tim

[briank]

I also need the dana 20 transfer case pivot box cover on the bottom of the transfer case.

[pound41]

I need the Drivers side exhaust manifold if you are willing to sell
Thanks

[JimH2828]

I see you will be answering all these posts this weekend, I decided to add to my list, which is below. Let me know, pics would be great.

1) Front seat mount parts, driver and pass
2) Ignition lock if it is a 1970 "J" keyway, other ignition switch assembly parts too, if price is right.
3) Tailgate seal brackets\trim
4) Duel wall top hardware
5) Emergency brake parts
6) Rear fender support bar parts, in front of rear tire
7) Ball bearing ash tray
8) Differential housing air vent fittings
9) Drum brake strut bars


Thanks
Jim

[midunes]

I'll take the front bumper, if you'll ship to 49441. Price

[72blazerblue]

I would like to buy each outer bracket that mounts the front bumper. Let me know what kind of shape these are in..
Thanks!

[Rem701]

how much for the steering wheel?

[68lowburb]

hi need the door latch reinforcement plates if you have them thanks

[IronCanine]

Interested in:

1)Rear seat mounting hardware
2)Would like to get in line for door reinforcing plates (only need drivers side). Would be interested in whole door pending condition.

What kind of shape are the wheels in?

Thanks.

[Bishops Trucks]

What shape is the gas tank in? Does it mount between the rear frame rails like the burbs? I want to relocate the tank from inside the cab.

[toyplumbertrucks]

It is a longshot but I will ask. How are the rear frame horns that hold the step bumper on? If they are good would you be willing to cut them off or would you be interested in selling the whole frame after iit is parted out? I am not in a hurry so let me know when you get a chance. Thanks.

[Jdubs71]

Interested in the rear spring hangers. The two that mount to the frame in front of the rear axle. Let me know what your price is shipped to 93657. Thanks

[Jake1971]

Interested in the gas filler neck if in good driver condition like this one shipped to 78602

[Rust Buster]

Originally Posted by Jake1971

Interested in the gas filler neck if in good driver condition like this one shipped to 78602

Sorry, This was in pretty bad shape and I'm keeping what's left of it to convert my 72 K20 to a bedside fill.
Thanks

[DeadheadNM]

Any chance the front brace for the seats that's spot welded under the floor pan is usable and you could carve it out?

[Rust Buster]

Sorry guys, the blazer is all parted out and gone. All that is left is the Dana 20 transfer case and engine.