NC 71 Super Cheyenne Project Parting - The 1947 - Present Chevrolet & GMC Truck Message Board Network

gcburdic · 08-18-2011, 05:28 PM

Well...couldn't sell her whole....so we'll part her out

Member Brn Agn and I will monitor this thread....

here's the build thread for her so you can see what we did...more pictures here too...

1. Chassis $1,200
(A 1967 short bed frame was sand blasted and painted with Eastwood Extreme Chassis Black paint (satin). The following parts are new: A-arm bushings, trailing arm bushings, rear axle u-bolts, front rotors, bearings, seals, tie rod ends, CPP 4" rear drop springs, CPP 2" front drop springs, CPP shocks. Grade 8 hardware was used to reassemble the chassis. The rear is the original 3.07 positraction axle. The chassis is currently sitting on 15x7 rally wheels. The chassis has also been dimpled to accommodate the power steering box which is included)
2. Cab with title $800
Cab includes windshield, back glass, dash pad (no good)....The rocker panels, cab corners, lower kick panels, lower a-pillars and front driver's side cab support have been replaced. No body filler has been used so the buyer can inspect the repaired areas and pictures were taken during the repair process and are available. The front windsield is fogged along the bottom, there's a dent below the roof seam on the passenger side
(look in the more pictures thread up top for all pictures of the cab)
3. Seat $100 (no ship) SOLD
4. Door panels $40 + ship
5. Very nice 71 Super Glovebox door No longer for sale
6. Dash Bezel $65 shipped (not original to the truck so it doesn't match the glovebox door woodgrain) SOLD to 71 super
7. Gas Tank $50 (no ship)
8. Front clip...No shipping on these items
rust free 69-72 rad support $150
clean cowl $25 SOLD
69-72 nice hood w/ hinges $100
71 pass fender (lower cup has been replaced...needs finished welded) $60 SOLD
71 dr fender $75 SOLD
71-72 grille (some dents and the inner has some small cracks) $100
dr side inner fender $40
9. Bed Parts....no ship on these parts
bedfloor $250
front panel $50
wheel wells $50
shortened lwb bedsides $150 for both
10. Doors $100 for both (rusted on bottoms....includes vents, glass, door innards, mirror (not good) and door handles (not good)) SOLD to frednoah
11. AC controller $45 shipped
12. ignition switch with key $20 shipped can include the door locks with this for additional $10
13. Lighter $15+ ship
14. Cheyenne emblems $10+ship SOLD
15. Super emblems $20 + ship SOLD
16. parchment visors and arm rests $50 shipped SOLD
17. NEW 69-72 cab mounting bushings/ hardware $50 +ship
18. NEW rad support bushings/mounts/ hardware for 68 $15+ship SOLD
19. brake booster/ MC $40 +ship
20. AC box on firewall $50 +ship This does have a little rust in the metal piece.
21. Black seat belts $100 SOLD
22 Extra Hood Hinges $25+ship SOLD
23 71 Head light bezels and head lights $30+ship
24. One piece piece drive shaft. $50 no ship
25. Two-piece LWB drive shaft. $50 no ship
26. A/T cross member. $25 +ship
27. V8 Engine stands. $25 +ship
28. Frame cuts...as needed (will get pictures up of what we have)

If ya need a picture let me know....

**DeadheadNM** · 08-18-2011, 05:33 PM

in line for belts pending pics. Thanks. Pete

Prathbun · 08-18-2011, 05:34 PM

I need to know whats included with the radiator support bushings/ mounts #18. First in line. Thanks

**rob32472** · 08-18-2011, 05:45 PM

I cant get the link to work so can you post a pic of the dent you spoke of?

Tuff Gong · 08-18-2011, 06:00 PM

in line for glove box door pending detailed pics of condition.

**blap** · 08-18-2011, 07:15 PM

I take the super emblems as long as the studs are intact.
PM sent

Leroy-B1 · 08-18-2011, 07:26 PM

Any lowering components? If so in line
Posted via Mobile Device

frednoah · 08-18-2011, 08:12 PM

I think I'd like the doors. Any chance you could bring em back down this way?

brn agn · 08-18-2011, 09:41 PM

Quote:

Originally Posted by DeadheadNM

in line for belts pending pics. Thanks. Pete

I will get you some pictures of the belts tomorrow.

Quote:

Originally Posted by Prathbun

I need to know whats included with the radiator support bushings/ mounts #18. First in line. Thanks

Geoff bought these and assembled the core support to the frame, so I will let him chime in with what is included.

Quote:

Originally Posted by rob32472

I cant get the link to work so can you post a pic of the dent you spoke of?

Here is the picture of the dent:

Try this link for cab pictures. I took 50+ today. The only thing I saw of any concern was some rust on the top windshield lip under the weather stripping. It looks like it will clean up to me.

http://s973.photobucket.com/albums/a...pZZ11QQtppZZ20

Quote:

Originally Posted by Brian Atkinson

in line for glove box door pending detailed pics of condition.

I will get you some additional pictures tomorrow as well.

Quote:

Originally Posted by blap

I take the super emblems as long as the studs are intact.
PM sent

The studs are intact, but I can take pictures of these tomorrow as well.

Quote:

Originally Posted by Leroy-B1

Any lowering components? If so in line
Posted via Mobile Device

The only lowering components we have are installed on the frame.

Quote:

Originally Posted by frednoah

I think I'd like the doors. Any chance you could bring em back down this way?

I'm sure we can work something out. I would like to get down there for Autofair in a couple of weeks. If that doesn't work out, I will be in Charlotte over Labor Day weekend sometime.

**rob32472** · 08-18-2011, 09:49 PM

Will you remove the windshield and take some pics of the rust you are speaking of? I am not concerned with the dent.

71meangreenc10 · 08-18-2011, 10:27 PM

Geoff,
You know I am looking for a good passenger fender for the burb.....

Smitty

mo · 08-19-2011, 01:05 AM

I'll take the glove box door as is...if Brian passes.
thanks.

btw whats he price?

Micks72 · 08-19-2011, 02:55 AM

ashtray?

astevens · 08-19-2011, 09:07 AM

Do you have any pics of the wheel wells? Thanks
Aaron

Prathbun · 08-19-2011, 09:54 AM

If #18 (radiator core support mounting stuff) contains 2 bolts, 2 square washers 2 upper and 2 lower rubber bushings with 2 nuts with washers, I'll take them. Other wise I'll pass.

Thanks

gcburdic · 08-19-2011, 10:27 AM

Quote:

Originally Posted by rob32472

Will you remove the windshield and take some pics of the rust you are speaking of? I am not concerned with the dent.

I'll let Jesse chime in...the winshield is fogged and has a crack, so it's not worth using....

Quote:

Originally Posted by 71meangreenc10

Geoff,
You know I am looking for a good passenger fender for the burb.....
Smitty

Smitty...look at this picture...we replaced the cup under the battery area, it just needs to be finished welded....so you're 1st if ya want it

Quote:

Originally Posted by Brian Atkinson

in line for glove box door pending detailed pics of condition.

Jesse will get more pictures for ya

Quote:

Originally Posted by mo

I'll take the glove box door as is...if Brian passes.
thanks.
btw whats he price?

You're 2nd in line....price is $125

Quote:

Originally Posted by Micks72

ashtray?

sorry...no ashtray

Quote:

Originally Posted by astevens

Do you have any pics of the wheel wells? Thanks
Aaron

Jesse will get more pictures for you...but here's one

Quote:

Originally Posted by Prathbun

If #18 (radiator core support mounting stuff) contains 2 bolts, 2 square washers 2 upper and 2 lower rubber bushings with 2 nuts with washers, I'll take them. Other wise I'll pass.
Thanks

Yep...that's what it includes....give us a couple days to get them off the truck and get ya a shipping price....cool?

Prathbun · 08-19-2011, 11:26 AM

Quote:

Originally Posted by Prathbun

If #18 (radiator core support mounting stuff) contains 2 bolts, 2 square washers 2 upper and 2 lower rubber bushings with 2 nuts with washers, I'll take them. Other wise I'll pass.

Thanks

I'll take them!!! Let me know how much and how I can send you money.

Thanks!!!

hatred · 08-19-2011, 04:06 PM

Passenger fender still available?

brn agn · 08-19-2011, 04:40 PM

Quote:

Originally Posted by DeadheadNM

in line for belts pending pics. Thanks. Pete

Seatbelt pics:

http://i973.photobucket.com/albums/a...r/IMG_5823.jpg
http://i973.photobucket.com/albums/a...r/IMG_5824.jpg
http://i973.photobucket.com/albums/a...r/IMG_5825.jpg
http://i973.photobucket.com/albums/a...r/IMG_5826.jpg
http://i973.photobucket.com/albums/a...r/IMG_5827.jpg
http://i973.photobucket.com/albums/a...r/IMG_5828.jpg
http://i973.photobucket.com/albums/a...r/IMG_5829.jpg

Quote:

Originally Posted by Prathbun

I need to know whats included with the radiator support bushings/ mounts #18. First in line. Thanks

Here are the pictures of the hardware. Please note that these are for a 67-68 model. You can PM me or Geoff for payment info.

http://i973.photobucket.com/albums/a...r/IMG_5831.jpg
http://i973.photobucket.com/albums/a...r/IMG_5832.jpg
http://i973.photobucket.com/albums/a...r/IMG_5833.jpg

Quote:

Originally Posted by Brian Atkinson

in line for glove box door pending detailed pics of condition.

Glovebox pics:

http://i973.photobucket.com/albums/a...r/IMG_5834.jpg
http://i973.photobucket.com/albums/a...r/IMG_5835.jpg
http://i973.photobucket.com/albums/a...r/IMG_5836.jpg
http://i973.photobucket.com/albums/a...r/IMG_5837.jpg
http://i973.photobucket.com/albums/a...r/IMG_5844.jpg
http://i973.photobucket.com/albums/a...r/IMG_5845.jpg

Quote:

Originally Posted by blap

I take the super emblems as long as the studs are intact.
PM sent

Emblem pics:

http://i973.photobucket.com/albums/a...r/IMG_5858.jpg
http://i973.photobucket.com/albums/a...r/IMG_5859.jpg

Quote:

Originally Posted by rob32472

Will you remove the windshield and take some pics of the rust you are speaking of? I am not concerned with the dent.

It is trying to rain here now. I'll try to pull it this weekend and get you some pics of the metal under the weather stripping.

Quote:

Originally Posted by 71meangreenc10

Geoff,
You know I am looking for a good passenger fender for the burb.....

Smitty

Smitty, here is what still needs to be repaired on this fender. You are first in line if you want it.

http://i973.photobucket.com/albums/a...r/IMG_5856.jpg
http://i973.photobucket.com/albums/a...r/IMG_5857.jpg

Quote:

Originally Posted by astevens

Do you have any pics of the wheel wells? Thanks
Aaron

Wheel well pics:

http://i973.photobucket.com/albums/a...r/IMG_5863.jpg
http://i973.photobucket.com/albums/a...r/IMG_5864.jpg
http://i973.photobucket.com/albums/a...r/IMG_5865.jpg
http://i973.photobucket.com/albums/a...r/IMG_5866.jpg
http://i973.photobucket.com/albums/a...r/IMG_5867.jpg
http://i973.photobucket.com/albums/a...r/IMG_5868.jpg
http://i973.photobucket.com/albums/a...r/IMG_5869.jpg
http://i973.photobucket.com/albums/a...r/IMG_5870.jpg

Quote:

Originally Posted by hatred

Passenger fender still available?

Smitty has first dibs and you are second in line if he does not want it. See pictures above to see the area that still needs to be repaired.

Tuff Gong · 08-19-2011, 05:34 PM

Thank you for posting the pics. However, I am going to pass on the purchase. Thank you for your time. I believe MO is next in line.

Quote:
Originally Posted by Brian Atkinson
in line for glove box door pending detailed pics of condition.
Glovebox pics:

http://i973.photobucket.com/albums/a...r/IMG_5834.jpg
http://i973.photobucket.com/albums/a...r/IMG_5835.jpg
http://i973.photobucket.com/albums/a...r/IMG_5836.jpg
http://i973.photobucket.com/albums/a...r/IMG_5837.jpg
http://i973.photobucket.com/albums/a...r/IMG_5844.jpg
http://i973.photobucket.com/albums/a...r/IMG_5845.jpg

VA72C10 · 08-19-2011, 06:44 PM

Any chance you'll be coming up to/through VA soon? I'd be interested in the complete bed if so....also the cab if rob passed...

2wd73blazer · 08-19-2011, 08:14 PM

put me in line for the cab

**rob32472** · 08-19-2011, 08:27 PM

Thanks!

**DeadheadNM** · 08-19-2011, 09:52 PM

Geoff,

1) Thanks for the pics. Real nice looking belts. Do you have a center belt and/or bolts to include? Retractors work well?

2) Does the cost of the bezel include the gauges? I could use a driver quality wood bezel but don't need more gauges.

Thanks again,

Pete

jeffg1010 · 08-19-2011, 10:01 PM

Put me in line for the drivers fender and the cowl for my dads Burb. Got some pics? (and the pass fender if Smitty definitely passes) package deal?!

Posted via Mobile Device

08-18-2011, 05:33 PM	#2
DeadheadNM Carpe manana Join Date: Dec 2010 Location: Eau Claire, WI Posts: 12,336	Re: 71 Super Cheyenne Project Parting in line for belts pending pics. Thanks. Pete __________________ 1972 K5 CST Highlander Blazer: http://67-72chevytrucks.com/vboard/s...d.php?t=708547 1972 K20 Cheyenne Super: http://67-72chevytrucks.com/vboard/s...d.php?t=528308 Members met: ORANGBLAZ, 2003 silverado, MikeCofield, BB72CHEVKT, Duncan&Son, Sameyrasmea72, THENEWMEXICAN, HotRod C/10, brianthelion02, Sport/Truck, ryanroo, michael bustamante, Dirt's72, Already Gone, WestButteTruck, 57taskforce, Moreyel, painterljp, AASmedic, SoCoC10, Lumaestas, carbuff382, Chevyland

08-18-2011, 05:34 PM	#3
Prathbun Registered User Join Date: Jul 2007 Location: Poplar Bluff, MO 63901 Posts: 293	Re: 71 Super Cheyenne Project Parting I need to know whats included with the radiator support bushings/ mounts #18. First in line. Thanks __________________ It's Not Rust, It's Patina!! 1967 C 20 Large Window, 700R4, 283, Tilt, PS, PB.....A Rusty But Trusty Gas Hog 2008 Silverado LTZ 1500 4x4

08-18-2011, 05:45 PM	#4
rob32472 Registered User Join Date: May 2007 Location: dallas ga Posts: 1,503	Re: 71 Super Cheyenne Project Parting I cant get the link to work so can you post a pic of the dent you spoke of?

08-18-2011, 06:00 PM	#5
Tuff Gong Registered User Join Date: Jan 2011 Location: Glendale, AZ Posts: 3,178	Re: 71 Super Cheyenne Project Parting in line for glove box door pending detailed pics of condition.

08-18-2011, 07:15 PM	#6
blap Senior Member Join Date: Nov 2008 Location: bristol,CT Posts: 580	Re: 71 Super Cheyenne Project Parting I take the super emblems as long as the studs are intact. PM sent

08-18-2011, 05:28 PM	#1
gcburdic Restoration Virgin! Join Date: Jan 2008 Location: Huntersville, NC Posts: 8,298	71 Super Cheyenne Project Parting Well...couldn't sell her whole....so we'll part her out Member Brn Agn and I will monitor this thread.... here's the build thread for her so you can see what we did...more pictures here too... 1. Chassis $1,200 (A 1967 short bed frame was sand blasted and painted with Eastwood Extreme Chassis Black paint (satin). The following parts are new: A-arm bushings, trailing arm bushings, rear axle u-bolts, front rotors, bearings, seals, tie rod ends, CPP 4" rear drop springs, CPP 2" front drop springs, CPP shocks. Grade 8 hardware was used to reassemble the chassis. The rear is the original 3.07 positraction axle. The chassis is currently sitting on 15x7 rally wheels. The chassis has also been dimpled to accommodate the power steering box which is included) 2. Cab with title $800 Cab includes windshield, back glass, dash pad (no good)....The rocker panels, cab corners, lower kick panels, lower a-pillars and front driver's side cab support have been replaced. No body filler has been used so the buyer can inspect the repaired areas and pictures were taken during the repair process and are available. The front windsield is fogged along the bottom, there's a dent below the roof seam on the passenger side (look in the more pictures thread up top for all pictures of the cab) 3. Seat $100 (no ship) SOLD 4. Door panels $40 + ship 5. Very nice 71 Super Glovebox door No longer for sale 6. Dash Bezel $65 shipped (not original to the truck so it doesn't match the glovebox door woodgrain) SOLD to 71 super 7. Gas Tank $50 (no ship) 8. Front clip...No shipping on these items rust free 69-72 rad support $150 clean cowl $25 SOLD 69-72 nice hood w/ hinges $100 71 pass fender (lower cup has been replaced...needs finished welded) $60 SOLD 71 dr fender $75 SOLD 71-72 grille (some dents and the inner has some small cracks) $100 dr side inner fender $40 9. Bed Parts....no ship on these parts bedfloor $250 front panel $50 wheel wells $50 shortened lwb bedsides $150 for both 10. Doors $100 for both (rusted on bottoms....includes vents, glass, door innards, mirror (not good) and door handles (not good)) SOLD to frednoah 11. AC controller $45 shipped 12. ignition switch with key $20 shipped can include the door locks with this for additional $10 13. Lighter $15+ ship 14. Cheyenne emblems $10+ship SOLD 15. Super emblems $20 + ship SOLD 16. parchment visors and arm rests $50 shipped SOLD 17. NEW 69-72 cab mounting bushings/ hardware $50 +ship 18. NEW rad support bushings/mounts/ hardware for 68 $15+ship SOLD 19. brake booster/ MC $40 +ship 20. AC box on firewall $50 +ship This does have a little rust in the metal piece. 21. Black seat belts $100 SOLD 22 Extra Hood Hinges $25+ship SOLD 23 71 Head light bezels and head lights $30+ship 24. One piece piece drive shaft. $50 no ship 25. Two-piece LWB drive shaft. $50 no ship 26. A/T cross member. $25 +ship 27. V8 Engine stands. $25 +ship 28. Frame cuts...as needed (will get pictures up of what we have) If ya need a picture let me know.... __________________ Geoff with a G 1968 Chevy C10 SWB The Mistress 1972 Custom Deluxe C20 Suburban A Suburban Named Isabella 1966 Ford Mustang Mama's High School Graduation Present Last edited by gcburdic; 09-03-2011 at 07:24 PM.

08-18-2011, 07:26 PM	#7
Leroy-B1 Registered User Join Date: Dec 2010 Location: Mars Hill, NC Posts: 1,994	Re: 71 Super Cheyenne Project Parting Any lowering components? If so in line Posted via Mobile Device

08-18-2011, 08:12 PM	#8
frednoah 86 Scottsdale Join Date: May 2010 Location: Mooresville NC Posts: 473	Re: 71 Super Cheyenne Project Parting I think I'd like the doors. Any chance you could bring em back down this way?

08-18-2011, 09:49 PM	#10
rob32472 Registered User Join Date: May 2007 Location: dallas ga Posts: 1,503	Re: 71 Super Cheyenne Project Parting Will you remove the windshield and take some pics of the rust you are speaking of? I am not concerned with the dent. Last edited by rob32472; 08-19-2011 at 06:46 AM.

08-18-2011, 10:27 PM	#11
71meangreenc10 Its a Truck Thing...... Join Date: Dec 2004 Location: Sierra Vista, Arizona Posts: 3,159	Re: 71 Super Cheyenne Project Parting Geoff, You know I am looking for a good passenger fender for the burb..... Smitty __________________ 71 C10 283/3SPD Full Resto 71 GMC 1500 Sierra Grande http://67-72chevytrucks.com/vboard/s...d.php?t=518599 70 C10 Suburban Former military GSA truck. 72 Chevy Blazer 4X4, Sloppy Jo, Mountain Climber. Wife says no more trucks. http://67-72chevytrucks.com/vboard/s...d.php?t=707378 72 GMC 1 Ton Motor Home, wife said no more trucks until she saw this one. Gen 3 6.0/4L80E 4.10 http://67-72chevytrucks.com/vboard/s...d.php?t=761110 68 GMC Suburban was 3/4 ton, now 1/2.Wife shook her head 71 C30 Wrecker 71 C20 Scott-Bilt As weird as it gets..BB Cheyenne AC Truck 68 GMC Long Stepside. They keep following me home 71 C20 Longhorn/Ole Yellor 69 C30 Former Motor Home, Flat Bed time

08-19-2011, 01:05 AM	#12
mo Registered User Join Date: Apr 2001 Location: santa barbara, ca Posts: 829	Re: 71 Super Cheyenne Project Parting I'll take the glove box door as is...if Brian passes. thanks. btw whats he price?

08-19-2011, 02:55 AM	#13
Micks72 Registered User Join Date: Jun 2011 Location: Lancaster, CA Posts: 140	Re: 71 Super Cheyenne Project Parting ashtray? __________________ *Mick* 1972 C20 Deluxe MADE IN the U.S.A.

08-19-2011, 09:07 AM	#14
astevens Registered User Join Date: May 2008 Location: Clarksburg, WV Posts: 335	Re: 71 Super Cheyenne Project Parting Do you have any pics of the wheel wells? Thanks Aaron

08-19-2011, 09:54 AM	#15
Prathbun Registered User Join Date: Jul 2007 Location: Poplar Bluff, MO 63901 Posts: 293	Re: 71 Super Cheyenne Project Parting If #18 (radiator core support mounting stuff) contains 2 bolts, 2 square washers 2 upper and 2 lower rubber bushings with 2 nuts with washers, I'll take them. Other wise I'll pass. Thanks __________________ It's Not Rust, It's Patina!! 1967 C 20 Large Window, 700R4, 283, Tilt, PS, PB.....A Rusty But Trusty Gas Hog 2008 Silverado LTZ 1500 4x4

08-19-2011, 04:06 PM	#18
hatred Registered User Join Date: Jun 2010 Location: Denham Springs, La. Posts: 257	Re: 71 Super Cheyenne Project Parting Passenger fender still available? __________________ 05 QSM GTO - M6, Corsa, King Springs 70 SWB CST - 350/Auto, Foose 18/17 I upset whiners too....



Register or Log In To remove these advertisements.

08-19-2011, 05:34 PM	#20
Tuff Gong Registered User Join Date: Jan 2011 Location: Glendale, AZ Posts: 3,178	Re: 71 Super Cheyenne Project Parting Thank you for posting the pics. However, I am going to pass on the purchase. Thank you for your time. I believe MO is next in line. Quote: Originally Posted by Brian Atkinson in line for glove box door pending detailed pics of condition. Glovebox pics: http://i973.photobucket.com/albums/a...r/IMG_5834.jpg http://i973.photobucket.com/albums/a...r/IMG_5835.jpg http://i973.photobucket.com/albums/a...r/IMG_5836.jpg http://i973.photobucket.com/albums/a...r/IMG_5837.jpg http://i973.photobucket.com/albums/a...r/IMG_5844.jpg http://i973.photobucket.com/albums/a...r/IMG_5845.jpg

08-19-2011, 06:44 PM	#21
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,269	Re: 71 Super Cheyenne Project Parting Any chance you'll be coming up to/through VA soon? I'd be interested in the complete bed if so....also the cab if rob passed... __________________ Looking for a 67-72 swb or blazer project in or around VA.

08-19-2011, 08:14 PM	#22
2wd73blazer Registered User Join Date: Jan 2008 Location: North Augusta,SC Posts: 801	Re: 71 Super Cheyenne Project Parting put me in line for the cab

08-19-2011, 08:27 PM	#23
rob32472 Registered User Join Date: May 2007 Location: dallas ga Posts: 1,503	Re: 71 Super Cheyenne Project Parting Thanks!

08-19-2011, 09:52 PM	#24
DeadheadNM Carpe manana Join Date: Dec 2010 Location: Eau Claire, WI Posts: 12,336	Re: 71 Super Cheyenne Project Parting Geoff, 1) Thanks for the pics. Real nice looking belts. Do you have a center belt and/or bolts to include? Retractors work well? 2) Does the cost of the bezel include the gauges? I could use a driver quality wood bezel but don't need more gauges. Thanks again, Pete __________________ 1972 K5 CST Highlander Blazer: http://67-72chevytrucks.com/vboard/s...d.php?t=708547 1972 K20 Cheyenne Super: http://67-72chevytrucks.com/vboard/s...d.php?t=528308 Members met: ORANGBLAZ, 2003 silverado, MikeCofield, BB72CHEVKT, Duncan&Son, Sameyrasmea72, THENEWMEXICAN, HotRod C/10, brianthelion02, Sport/Truck, ryanroo, michael bustamante, Dirt's72, Already Gone, WestButteTruck, 57taskforce, Moreyel, painterljp, AASmedic, SoCoC10, Lumaestas, carbuff382, Chevyland

08-19-2011, 10:01 PM	#25
jeffg1010 Registered User Join Date: Aug 2010 Location: Mooresville, NC Posts: 2,675	Re: 71 Super Cheyenne Project Parting Put me in line for the drivers fender and the cowl for my dads Burb. Got some pics? (and the pass fender if Smitty definitely passes) package deal?! Posted via Mobile Device __________________ Jeff 1972 Blazer CST 2wd- My son Sam's Project "S" Project "S" 1970 Suburban - SOLD "One Bad Burb" Photobucket Album 1986 C30 Crewcab - 63K original miles, original paint Members I have met: mikey531, gcburdic, bashed, burbman69, TonyPieras, Blazester, GCncsuHD, custombuilt67-72, tsnow678, highrpm, PanelDeland, tanman722001, 47thriftmaster, babyblueoval, 68stepbed, JesseWebb, Andy4639, xs-style, TobyArnot, BigOrange, frednoah, brn_agn, k5hart, Graham57a, bhelton, AJohn6, SilverC10, 69CST, '71 Flame, RaceAGMC, Liz, Josh, MattPSU, 68corvair, Chevy350V8, mdeal, ccrorymc, mrhurt73, dmxxpert, Custom68, 84GMC, BionicABs1, BigBlockBurris, Ebfabman, ATP... Last edited by jeffg1010; 08-19-2011 at 10:56 PM.

Register or Log In To remove these advertisements.