Is my drive shaft toast? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

spudz · 12-14-2010, 07:30 PM

I pulled the drive shaft from my 79 c30 today to replace the u-joints. Upon doing so, I could slide the carrier bearing off the shaft! I know this bearing is pressed on. Maybe someone turned it down? or a hacked old repair where the bearing ate it out? I dint know. I just know that your not supposed to be able to slide it on and off. I bought a new carrier bearing and it does the same thing.. you can see in the pic, the area on the left is smaller then the little 1/4in space where the spacer ring goes. you can see the line. Sorry for the crappy cell pics, I didn't have my camera at work. Is there anything I can do short of finding a new shaft? Anyone have the front half drive shaft in SC they want to sell? just my luck... oh well. :-(

*78 Chevyrado* · 12-14-2010, 08:11 PM

I think it would be toast unless theres some kind of sleeve kit or undersize bearing available.

spudz · 12-14-2010, 08:22 PM

thats what I was wondering. If there is a sleeve kit like a harmonic balancer repair sleeve or something., this sucks... I had to get a ride home from work lol.

**old Rusty C10** · 12-14-2010, 09:28 PM

i had an old dodge like that the carrier bearing was shot and the thing slid on and off . I put it back together and drove the truck with the replaced sliding carrier and it was fine .

spudz · 12-14-2010, 10:01 PM

I didn't even notice any slop in it while bolted in the truck. Just slid off when I removed it. I think I am going to reinstall the original bearing with new joints until I can find a replacement front shaft. Then I will install the new bearing on the new shaft. I will hit the local junk yards tomorrow and see if I can find anything.

12-14-2010, 07:30 PM	#1
spudz Registered User Join Date: Oct 2005 Location: Branchville SC Posts: 1,647	Is my drive shaft toast? I pulled the drive shaft from my 79 c30 today to replace the u-joints. Upon doing so, I could slide the carrier bearing off the shaft! I know this bearing is pressed on. Maybe someone turned it down? or a hacked old repair where the bearing ate it out? I dint know. I just know that your not supposed to be able to slide it on and off. I bought a new carrier bearing and it does the same thing.. you can see in the pic, the area on the left is smaller then the little 1/4in space where the spacer ring goes. you can see the line. Sorry for the crappy cell pics, I didn't have my camera at work. Is there anything I can do short of finding a new shaft? Anyone have the front half drive shaft in SC they want to sell? just my luck... oh well. :-( Attached Images __________________ 2004 z71, 96 z71 on 38s, 88 Chevy k5 blazer, 4in lift. 84 swb project, 82 SWB project , 84 chevy 4x4 lwb project, 88 Jimmy beater/highschool ride. 79 c30. 99 tahoe 4x4 project. and a bunch of parts trucks.. Last edited by spudz; 12-14-2010 at 10:09 PM.

12-14-2010, 08:11 PM	#2
78 Chevyrado Account Suspended Join Date: Dec 2007 Location: Unnapreciative, Trollville Posts: 2,079	Re: Is my drive shaft toast? I think it would be toast unless theres some kind of sleeve kit or undersize bearing available.

12-14-2010, 08:22 PM	#3
spudz Registered User Join Date: Oct 2005 Location: Branchville SC Posts: 1,647	Re: Is my drive shaft toast? thats what I was wondering. If there is a sleeve kit like a harmonic balancer repair sleeve or something., this sucks... I had to get a ride home from work lol. __________________ 2004 z71, 96 z71 on 38s, 88 Chevy k5 blazer, 4in lift. 84 swb project, 82 SWB project , 84 chevy 4x4 lwb project, 88 Jimmy beater/highschool ride. 79 c30. 99 tahoe 4x4 project. and a bunch of parts trucks.. Last edited by spudz; 12-14-2010 at 10:08 PM.

12-14-2010, 09:28 PM	#4
old Rusty C10 Robert Olson Transport Join Date: Oct 2002 Location: recent transplant to NC USA Posts: 20,277	Re: Is my drive shaft toast? i had an old dodge like that the carrier bearing was shot and the thing slid on and off . I put it back together and drove the truck with the replaced sliding carrier and it was fine . __________________ Bob 1951 International running on a squarebody chassis "If a man's worth is judged by the people he associates himself with, then i am the richest man in the world knowing some of the fine people of this board" http://67-72chevytrucks.com/vboard/a...t.php?f=25&a=9 (you can review the site rules here!) PM Me for your vehicle/parts hauling needs in the North East US or see my Facebook page Robert Olson Transport Live each day to the fullest.. you never know when fate is going to pull the rug out from under you... I hate cancer!!

12-14-2010, 10:01 PM	#5
spudz Registered User Join Date: Oct 2005 Location: Branchville SC Posts: 1,647	Re: Is my drive shaft toast? I didn't even notice any slop in it while bolted in the truck. Just slid off when I removed it. I think I am going to reinstall the original bearing with new joints until I can find a replacement front shaft. Then I will install the new bearing on the new shaft. I will hit the local junk yards tomorrow and see if I can find anything. __________________ 2004 z71, 96 z71 on 38s, 88 Chevy k5 blazer, 4in lift. 84 swb project, 82 SWB project , 84 chevy 4x4 lwb project, 88 Jimmy beater/highschool ride. 79 c30. 99 tahoe 4x4 project. and a bunch of parts trucks.. Last edited by spudz; 12-14-2010 at 10:10 PM.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.