PCM programming in Phoenix, AZ - The 1947 - Present Chevrolet & GMC Truck Message Board Network

azsmokey · 02-13-2011, 01:37 PM

Can anyone recommend a reputable shop/person that can assist us with reprogramming our PCM?

We have a 72 K-10 with a Vortech SC'd 6.0/4L65E/NP205 combo. We used the Painless 60221 powertrain harness. Painless states that the PCM needs reprogramming prior to successful startup. At this point the engine cranks and all systems appear nominal, however it will not run. Unless I missed something, which is quite possible, I probably should have the PCM done.

Any ideas, comments, suggestions?

Thanks

67C10BUB · 02-13-2011, 01:39 PM

I thought that Painless included ECM tuning with the purchase of their harness. If not then I went with Speartech and have been happy so far.

**Clyde65** · 02-13-2011, 03:13 PM

Nelson Performance is who I am going with, they are in San Antonio.

http://www.nelsonperformance.com/NPTuneInfo.htm

azsmokey · 02-13-2011, 05:32 PM

Quote:

I thought that Painless included ECM tuning with the purchase of their harness. If not then I went with Speartech and have been happy so far.

They do include PCM reprogramming with the purchase of the harness. However, I would prefer to have someone in the Phoenix area handle that task for a multitude of reasons. If that is not possible I will send it out.

67C10BUB · 02-13-2011, 06:23 PM

I don't know of anyone in AZ.
Posted via Mobile Device

matthew20061 · 02-14-2011, 03:30 AM

Try this place, I believe a guy named zippy (Mike) works there, he's been tuning for a very long time and very good at it. He did the tune for my truck over the phone for the 5.3L with a cam and now for the modded 6.0L. I contacted him directly, via Silveradoss.com username zippy. Here's the link for the place he works: http://www.adsautorepair.com/hp_customtuning.htm

c10seconds · 02-15-2011, 06:02 AM

If you haven't found anybody go to arizona dyno chip and they'll hook you up.
Posted via Mobile Device

68 c10 ls2 · 02-18-2011, 11:42 PM

Quote:

Originally Posted by matthew20061

Try this place, I believe a guy named zippy (Mike) works there, he's been tuning for a very long time and very good at it. He did the tune for my truck over the phone for the 5.3L with a cam and now for the modded 6.0L. I contacted him directly, via Silveradoss.com username zippy. Here's the link for the place he works: http://www.adsautorepair.com/hp_customtuning.htm

Please go se Zippy!!!! He does AWSOME work!! He is tuning my truck via e-mail and tuned my buddys LSX427 Suburban (1000hp, 725hp to the wheels). Zippy is the BEST when it comes to tuning any setup!! You will be very happy!!!

02-13-2011, 01:37 PM	#1
azsmokey Registered User Join Date: Dec 2007 Location: Glendale, AZ Posts: 156	PCM programming in Phoenix, AZ Can anyone recommend a reputable shop/person that can assist us with reprogramming our PCM? We have a 72 K-10 with a Vortech SC'd 6.0/4L65E/NP205 combo. We used the Painless 60221 powertrain harness. Painless states that the PCM needs reprogramming prior to successful startup. At this point the engine cranks and all systems appear nominal, however it will not run. Unless I missed something, which is quite possible, I probably should have the PCM done. Any ideas, comments, suggestions? Thanks

02-13-2011, 01:39 PM	#2
67C10BUB Registered User Join Date: Aug 2010 Location: Alta Loma, CA Posts: 610	Re: PCM programming in Phoenix, AZ I thought that Painless included ECM tuning with the purchase of their harness. If not then I went with Speartech and have been happy so far. __________________ 67 5.3L Build

02-13-2011, 03:13 PM	#3
Clyde65 1965 Chevy C10, 2005 4.8L/4l60 Join Date: Aug 2004 Location: DFW Texas Posts: 8,540	Re: PCM programming in Phoenix, AZ Nelson Performance is who I am going with, they are in San Antonio. http://www.nelsonperformance.com/NPTuneInfo.htm __________________ Clyde65 Rebuild of Clyde http://67-72chevytrucks.com/vboard/s...84#post8338184 69 Aristocrat Lo Liner build http://67-72chevytrucks.com/vboard/s...84#post7561684 *support our troops!*

02-13-2011, 06:23 PM	#5
67C10BUB Registered User Join Date: Aug 2010 Location: Alta Loma, CA Posts: 610	Re: PCM programming in Phoenix, AZ I don't know of anyone in AZ. Posted via Mobile Device __________________ 67 5.3L Build

02-14-2011, 03:30 AM	#6
matthew20061 69' Chevy Stepside Join Date: Mar 2008 Location: Anchorage, Ak Posts: 526	Re: PCM programming in Phoenix, AZ Try this place, I believe a guy named zippy (Mike) works there, he's been tuning for a very long time and very good at it. He did the tune for my truck over the phone for the 5.3L with a cam and now for the modded 6.0L. I contacted him directly, via Silveradoss.com username zippy. Here's the link for the place he works: http://www.adsautorepair.com/hp_customtuning.htm __________________ -Matthew -69' Chevy Custom/10 Shortbed Stepside 2WD "Copperhead" - Restored, 6.0L LQ9 Built. L92 Heads and LS3 Intake with Comp Cam 223/231 .610/.617 112 LSA, 4L60E with Shift Kit and Circle-D 3200 Stall Converter ~Build Thread -1957 Chevy BelAir 2 Door Post Sedan, Full Frame off Restoration done myself - 6.0L with T56 six speed -1957 Chevy BelAir 2 Door Post Sedan - Nearly rust free AK car, Project in the waiting -2003' Chevy Silverado SS AWD 6.0L! - Daily Driver Last edited by matthew20061; 02-14-2011 at 03:31 AM.

02-15-2011, 06:02 AM	#7
c10seconds Registered User Join Date: Oct 2009 Location: gilbert,AZ Posts: 947	Re: PCM programming in Phoenix, AZ If you haven't found anybody go to arizona dyno chip and they'll hook you up. Posted via Mobile Device



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.