|
|
|
01-04-2013, 11:36 AM
|
#1 |
|
Registered User
Join Date: May 2012
Location: Houston
Posts: 461
|
Re: Jesses' 48 PU
my best buddy giving me a hand.
__________________
 Semper FiCheck out my project: http://67-72chevytrucks.com/vboard/s...d.php?t=559086 |
|
|
|
01-04-2013, 11:38 AM
|
#2 |
|
Registered User
Join Date: May 2012
Location: Houston
Posts: 461
|
Re: Jesses' 48 PU
moved it around... took off the rear end.
__________________
Semper FiCheck out my project: http://67-72chevytrucks.com/vboard/s...d.php?t=559086 |
|
|
|
|
01-04-2013, 11:40 AM
|
#3 |
|
Registered User
Join Date: May 2012
Location: Houston
Posts: 461
|
Re: Jesses' 48 PU
mocked up the 73 Camaro clip and decided that BAM was right, it runs a bit wide, so decided to get rid of it
__________________
Semper FiCheck out my project: http://67-72chevytrucks.com/vboard/s...d.php?t=559086 |
|
|
|
|
01-04-2013, 11:44 AM
|
#4 |
|
Registered User
Join Date: May 2012
Location: Houston
Posts: 461
|
Re: Jesses' 48 PU
replaced the clip with a 1997 S-10 IFS. I welded a support jig on it, that way I could set it in place and it not move. I measured about 100 times to ensure it was centered.
__________________
Semper FiCheck out my project: http://67-72chevytrucks.com/vboard/s...d.php?t=559086 |
|
|
|
|
01-04-2013, 11:46 AM
|
#5 |
|
Registered User
Join Date: May 2012
Location: Houston
Posts: 461
|
Re: Jesses' 48 PU
welded support pieces inside and out before boxing in the frame
__________________
Semper FiCheck out my project: http://67-72chevytrucks.com/vboard/s...d.php?t=559086 |
|
|
|
|
01-04-2013, 11:54 AM
|
#6 |
|
Registered User
Join Date: May 2012
Location: Houston
Posts: 461
|
Re: Jesses' 48 PU
started boxing in the frame, figured out I wasnt strong enough to bend the 1/4 inch steel with my punny arms and my vice, so had to buy a shop press. Made a tool with angle iron and a piece of 1/4 inch scrap metal and waaalaaa... i was able to manipulate the braces to do as I wanted...
hmmm wonder if it will work with my wife too???
__________________
Semper FiCheck out my project: http://67-72chevytrucks.com/vboard/s...d.php?t=559086 |
|
|
|
|
01-04-2013, 11:56 AM
|
#7 |
|
Registered User
Join Date: May 2012
Location: Houston
Posts: 461
|
Re: Jesses' 48 PU
so after a long day of cutting, bending and welding.. well this is the result...
__________________
Semper FiCheck out my project: http://67-72chevytrucks.com/vboard/s...d.php?t=559086 |
|
|
|
|
01-05-2013, 12:30 PM
|
#8 | |
|
Registered User
Join Date: Nov 2011
Location: Langley, BC
Posts: 702
|
Re: Jesses' 48 PU
Quote:
__________________
56 Chevy PU http://67-72chevytrucks.com/vboard/s...d.php?t=531955 Question: Know how to sell your truck for $50,000? Answer: Spend $100,000 building it. |
|
|
|
|
 |
| Bookmarks |
|
|
Hybrid Mode
