03-25-2017, 06:34 PM | #101 |
Registered User
Join Date: Jun 2016
Location: Cornelius, NC
Posts: 167
|
Re: 1972 Blazer CST Frame off Project in NC
Ok, I need some help.
Does anyone know the torque settings for the ball joints on the drag link that goes from front tire to front tire? I looked in the service manual and I THINK its 50 ft-lbs, then turn to the next cotter pin hole, but I can't tell for sure. The book doesn't call it a drag link or center link and only refers to a tie rod - which I think is the rod that goes from the pitman arm to the steering arm. I also looked in the assembly guide - - no dice. Heres a pic from the assembly guide of the ball joint I am speaking of.......thanks guys. |
03-26-2017, 08:30 AM | #102 |
Senior Member
Join Date: Nov 2013
Location: East Tennessee
Posts: 2,182
|
Re: 1972 Blazer CST Frame off Project in NC
Tie rod is what goes from steering knuckle....... to steering knuckle...drag link connects pitman arm to steering arm....what you are referring to is the "tie rod end"
I have a torque chart somewhere if I can find it. from LMC catalog:
__________________
1967 C10 Step side 1968 C10 Step side 1970 Chevrolet K/5 Blazer 1972 Chevrolet K/5 Blazer ............. Last edited by A1971Blazer; 03-26-2017 at 09:46 AM. |
03-26-2017, 09:46 AM | #103 |
Registered User
Join Date: Mar 2015
Location: Ontario Canada
Posts: 1,523
|
Re: 1972 Blazer CST Frame off Project in NC
There's no need for factory specs because the size of the bolt and it's grade will determine what's needed for the proper torque. I have this chart posted on the shop wall.
|
04-02-2017, 09:14 AM | #104 |
Registered User
Join Date: Jun 2016
Location: Cornelius, NC
Posts: 167
|
Re: 1972 Blazer CST Frame off Project in NC
Attempting some progress this weekend - but as always, hit some snags.
I was reviewing some build threads looking at steering dampers and stumbled across this pic on Big J's build of a front parking brake cable support. See pic from his build below. I have the two smaller rear ones that are about 3 - 4 inches long, but I don't have a longer one for the front passenger side. That one looks 14 to 16 inches long. One, am I supposed to have it (assume answer is yes) on a 1972 and two, any ideas on a source? Not shocked I don't have it as the the PO's work included taking the rear drums parking brake lever out from between the shoes, so clearly it didn't have a functioning parking brake..... |
04-02-2017, 09:40 AM | #105 |
Carpe manana
Join Date: Dec 2010
Location: Eau Claire, WI
Posts: 12,422
|
Re: 1972 Blazer CST Frame off Project in NC
Yes supposed to have one. A wtb on the parts board should turn up. I'll look here to see if I have one to spare.
__________________
1972 K5 CST Highlander Blazer: http://67-72chevytrucks.com/vboard/s...d.php?t=708547 1972 K20 Cheyenne Super: http://67-72chevytrucks.com/vboard/s...d.php?t=528308 Members met: ORANGBLAZ, 2003 silverado, MikeCofield, BB72CHEVKT, Duncan&Son, Sameyrasmea72, THENEWMEXICAN, HotRod C/10, brianthelion02, Sport/Truck, ryanroo, michael bustamante, Dirt's72, Already Gone, WestButteTruck, 57taskforce, Moreyel, painterljp, AASmedic, SoCoC10, Lumaestas, carbuff382, Chevyland |
04-02-2017, 09:26 PM | #106 |
Registered User
Join Date: Jun 2016
Location: Cornelius, NC
Posts: 167
|
Re: 1972 Blazer CST Frame off Project in NC
This is my parking brake setup based on the parts I have from the PO and the ebrake kit I bought from Inline Tube. Weird that they left the 2 little intermediate line holders but not the long one.
|
04-02-2017, 09:54 PM | #107 |
Registered User
Join Date: Jun 2016
Location: Cornelius, NC
Posts: 167
|
Re: 1972 Blazer CST Frame off Project in NC
Had a good weekend - got almost everything off the to do list for the weekend.
DONE: ** Rear brakes completed, including having to fabricate an adjuster opening in the brake backer plate. I don't think I've posted this before, but when I rebuilt the rear axles, I replaced the stock brake backer plates with an original set of heavy duty brake backer plates. This gives me a set of shoes that are 2 3/4" wide versus 2", so I gained about 30% of stopping power. I decided I wanted to keep rear drums for three reasons - 1) 70% of braking is in the front and with my new slotted rotors and dual caliper Wilwoods, that seemed sufficient. 2) Rear discs move you to a 16" wheel and I wanted to stay with 15" - that backfired when I had to move to 16" wheels due to front clearance. And, 3) Rear discs cost almost triple what this cost me. ** Tie rod cleaned, POR-15'd, tie rod ends installed and mounted ** Fuel tank modified (swapped filler neck from old tank to new tank), repainted - and POR-15'd the straps. Would've mounted it too if I'd had four arms - - or a helper. NOT DONE: ** Steering damper not installed. I bought a Monroe shock and had some clearance issues - plus I just didn't like the Monroe shock. I am going to try a Bilstein. Now, some pics.......and A ROLLING CHASIS! |
04-02-2017, 09:56 PM | #108 |
Registered User
Join Date: Jun 2016
Location: Cornelius, NC
Posts: 167
|
Re: 1972 Blazer CST Frame off Project in NC
Rest of the pics:
|
04-03-2017, 10:18 AM | #109 |
Registered User
Join Date: Apr 2016
Location: Charlotte, NC
Posts: 59
|
Re: 1972 Blazer CST Frame off Project in NC
Looking great Chris. Congrats on getting her rolling! That parking brake cable support looks easy enough to make yourself if you don't come across one.
|
04-05-2017, 06:02 AM | #110 |
Registered User
Join Date: Jun 2016
Location: Cornelius, NC
Posts: 167
|
Re: 1972 Blazer CST Frame off Project in NC
Hey guys - - I am curious if anyone has any advice on what to complete BEFORE putting the tub back on the body. My body guy texted and he is in the final stages - exciting and scary!
So far, here is what I have done: * Run all brake and fuel lines * Installed leaf springs, axles and shocks * Installed engine and trans crossmembers * Front and Rear brakes * Wheels and tires * Parking Brake installed Still left to do (at least in my mind): * Fuel tank, sending unit and rubber fuel lines * Transfer Case and Trans installed * Drive shafts installed Then put the tub on Not sure if there is anything else - tail light wires, etc - but all that seems like it would be easy post tub install. Appreciate any suggestions from guys that have been there, done that. Thanks! |
04-05-2017, 06:06 AM | #111 | |
Registered User
Join Date: Jun 2016
Location: Cornelius, NC
Posts: 167
|
Re: 1972 Blazer CST Frame off Project in NC
Quote:
And had an interesting find last week. I was looking at torque converters and discovered a guy here in Cornelius who builds them for racers all over the world. One man shop, super knowledgeable and professional. He is building mine for me and I should have it next week. The beauty of a local guy is service after the sale - he said if I was in any way unhappy with its stall limit (after I get everything back together), he'd adjust it for me for free. Hard to beat. |
|
04-05-2017, 09:38 PM | #112 |
Registered User
Join Date: May 2007
Location: Rapid City South Dakota
Posts: 2,359
|
Re: 1972 Blazer CST Frame off Project in NC
If they are done, I would install the engine, trans, and transfer case, before the tub.
__________________
Turp Mcspray New life for an old 2wd, farm blazer http://67-72chevytrucks.com/vboard/s...d.php?t=505987 My Blazer build http://67-72chevytrucks.com/vboard/s...d.php?t=342299 |
04-09-2017, 08:44 PM | #113 | |
Registered User
Join Date: Jun 2016
Location: Cornelius, NC
Posts: 167
|
Re: 1972 Blazer CST Frame off Project in NC
Quote:
I did tackle the Transfer Case - and got it mostly installed. I ran into a problem with the bolts for the side of the transfer case that connects it to the frame - the 3 piece stabilizer with the rubber bushings. I tried to reinstall the bolts from the PO and they would get tight, then slip the thread and be loose again. So, I went and got new bolts - 9/16-12 and it still felt loose in the thread. Tried to torque it up and same thing - - once it got past snug, it slipped the thread. So I thought I have the wrong bolt for sure. Bought a 5/8-11 but couldn't get it started. Also picked up some M14 (too small and slid right into the hole) and M16 (wouldn't thread, like the 5/8), and neither worked. So, I am guessing the 9/16-12 is the right bolt and pitch, but thats not fixing my slipping problem. Anyone got a recommendation on a fix - - or a confirmation on bolt size? I know alot of guys run without this brace, but I want it on there. Thanks - - kinda stuck |
|
04-10-2017, 07:07 AM | #114 |
2WD Jimmy
Join Date: Mar 2005
Location: Davis County, Utah
Posts: 2,565
|
Re: 1972 Blazer CST Frame off Project in NC
I am guessing you are sure the threads are not stripped.
|
04-10-2017, 09:27 AM | #115 |
Registered User
Join Date: Jun 2016
Location: Cornelius, NC
Posts: 167
|
Re: 1972 Blazer CST Frame off Project in NC
|
04-10-2017, 09:52 AM | #116 |
Senior Member
Join Date: Nov 2013
Location: East Tennessee
Posts: 2,182
|
Re: 1972 Blazer CST Frame off Project in NC
look down past the bad threads...if there are a few good ones below them...just get a slightly longer bolt so it will catch the good threads...
__________________
1967 C10 Step side 1968 C10 Step side 1970 Chevrolet K/5 Blazer 1972 Chevrolet K/5 Blazer ............. |
04-10-2017, 07:12 PM | #117 |
Registered User
Join Date: Jun 2016
Location: Cornelius, NC
Posts: 167
|
Re: 1972 Blazer CST Frame off Project in NC
|
04-10-2017, 07:18 PM | #118 |
Registered User
Join Date: Jun 2016
Location: Cornelius, NC
Posts: 167
|
Re: 1972 Blazer CST Frame off Project in NC
Finally something cool to share - - COLOR!!!!!!
I don't think the pics do it justice. |
04-10-2017, 08:40 PM | #119 |
I'm trying....
Join Date: Oct 2013
Location: Athens, GA
Posts: 2,701
|
Re: 1972 Blazer CST Frame off Project in NC
Congrats. Looking good. Great color. Well into the fun stuff now.
__________________
1970 K20 Z62 https://67-72chevytrucks.com/vboard/...56#post9334756 1970 Blazer http://67-72chevytrucks.com/vboard/s...d.php?t=645076 1969 K10 SWB CST http://67-72chevytrucks.com/vboard/s...52#post8520352 1971 K20 Z84 https://67-72chevytrucks.com/vboard/...90#post9047290 1946 B.F. Avery Model A Tractor http://67-72chevytrucks.com/vboard/s...55#post8292555 "Sometimes I wonder if zander208 was even real..." |
04-11-2017, 03:20 PM | #120 |
Registered 1971 K5
Join Date: Dec 2008
Location: SO.CEN.CAL
Posts: 428
|
Re: 1972 Blazer CST Frame off Project in NC
That's a beautiful color!
|
04-11-2017, 07:36 PM | #121 |
Registered User
Join Date: Jun 2016
Location: Cornelius, NC
Posts: 167
|
Re: 1972 Blazer CST Frame off Project in NC
Thanks guys - very pleased with how the color turned out.
|
04-12-2017, 10:26 PM | #122 | |
Registered User
Join Date: Jun 2016
Location: Cornelius, NC
Posts: 167
|
Re: 1972 Blazer CST Frame off Project in NC
Quote:
The silver lining is it's fixed now and I met an awesome machinist in the process. A true craftsman. |
|
04-13-2017, 09:24 AM | #123 |
Senior Member
Join Date: Jun 2002
Location: Murray, Kentucky
Posts: 3,568
|
Re: 1972 Blazer CST Frame off Project in NC
Great job on this, the paint is amazing!
Rg
__________________
Roger '68 Short step - https://67-72chevytrucks.com/vboard/...d.php?t=849675 '69 ('70?) 2wd Blazer '70 GMC Jimmy 2wd '73 Firebird - https://67-72chevytrucks.com/vboard/...d.php?t=853203 |
04-14-2017, 12:52 AM | #124 |
Registered User
Join Date: Aug 2013
Location: Central Coast, CA
Posts: 774
|
Re: 1972 Blazer CST Frame off Project in NC
Awesome! I bet you are stoked to have the paint finished.
__________________
My Build Thread 72 K5 http://67-72chevytrucks.com/vboard/s...d.php?t=628612 Build version 2.0: 72 K5 6.0 LQ9, 4L80e, NP205 http://67-72chevytrucks.com/vboard/s...d.php?t=793192 ____________________________________________ 1972 CST K5 Blazer Dark Olive |
04-17-2017, 09:25 PM | #125 |
Senior Member
Join Date: May 2006
Location: Philadelphia, Pa. 19454
Posts: 9,691
|
Re: 1972 Blazer CST Frame off Project in NC
are you still looking for the long piece for the e brake?
nice build luv the paint
__________________
Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim |
Bookmarks |
|
|