Rear end options for a 62 c10 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

62427stepside · 06-05-2019, 06:00 PM

Ok so I just purchased a 62 stepside. I’m going to replace the front suspension from a 79 c10 . What can I do for the rear to go from 6 lug to 5 x 5 to match the front?
Posted via Mobile Device

b454rat · 06-05-2019, 06:10 PM

The rear should be an Eaton, don't think there is any 5 luggers for it. Tho a different type of truck, I had a 62 4wd burb that I swapped 3/4 ton axles into. Rear was a bolt in Dana 60 from a 78/79 Ford. Why not use the axle from the donor?

**Clyde65** · 06-05-2019, 06:31 PM

Take the axles out, replace bearings if needed, take the axles to a racing machine shop, have them fill and redrill the bolt pattern to what you need. Make sure they turn down the center of the axle hub a bit

62427stepside · 06-05-2019, 06:52 PM

Quote:

Originally Posted by Clyde65

Take the axles out, replace bearings if needed, take the axles to a racing machine shop, have them fill and redrill the bolt pattern to what you need. Make sure they turn down the center of the axle hub a bit

I’ll check into that. Is there a posi unit available for the stock rear end?
Posted via Mobile Device

**Captainfab** · 06-05-2019, 11:08 PM

The Eaton HO32/33 differential that is currently under your truck more than likely has 3.90 gears in it. Depending on what your plans are as far as engine, trans and rear tire size, you might consider changing the entire differential. The '79 12 bolt will work once you weld on the trailing arm mounts and a panhard bar mount, but it will also be 1.5" wider than the Eaton. The increased width may or may not be an issue depending on what rear tires you plan to run. If the width is an issue, look for a '63-'70 truck 12 bolt. They will be the same width as your Eaton and conversion axles are readily available.

BTW, I love those wheels.

62427stepside · 06-05-2019, 11:29 PM

Quote:

Originally Posted by Captainfab

The Eaton HO32/33 differential that is currently under your truck more than likely has 3.90 gears in it. Depending on what your plans are as far as engine, trans and rear tire size, you might consider changing the entire differential. The '79 12 bolt will work once you weld on the trailing arm mounts and a panhard bar mount, but it will also be 1.5" wider than the Eaton. The increased width may or may not be an issue depending on what rear tires you plan to run. If the width is an issue, look for a '63-'70 truck 12 bolt. They will be the same width as your Eaton and conversion axles are readily available.

BTW, I love those wheels.

Thanks truck currently has a 427 with a 4 speed. I plan to change it to s automatic. Tires on it are 33 x11.5 I like the wheels also put the wife insists on chrome.
Posted via Mobile Device

**slepysal** · 06-05-2019, 11:36 PM

I used one out of a '67 that had 3.73 as mentioned on 60-62 you have to relocate the trailing arm mounts and swap out the pan hard bar.

62427stepside · 06-05-2019, 11:53 PM

Quote:

Originally Posted by slepysal

I used one out of a '67 that had 3.73 as mentioned on 60-62 you have to relocate the trailing arm mounts and swap out the pan hard bar.

Thanks
Posted via Mobile Device

**slepysal** · 06-06-2019, 12:13 AM

no worries... by the way nice looking truck

06-05-2019, 06:00 PM	#1
62427stepside Registered User Join Date: May 2019 Location: Loganton Pa Posts: 4	Rear end options for a 62 c10 Ok so I just purchased a 62 stepside. I’m going to replace the front suspension from a 79 c10 . What can I do for the rear to go from 6 lug to 5 x 5 to match the front? Posted via Mobile Device Attached Images

06-05-2019, 06:10 PM	#2
b454rat Senior Member Join Date: May 2004 Location: Binghamton, NY Posts: 3,454	Re: Rear end options for a 62 c10 The rear should be an Eaton, don't think there is any 5 luggers for it. Tho a different type of truck, I had a 62 4wd burb that I swapped 3/4 ton axles into. Rear was a bolt in Dana 60 from a 78/79 Ford. Why not use the axle from the donor?

06-05-2019, 06:31 PM	#3
Clyde65 1965 Chevy C10, 2005 4.8L/4l60 Join Date: Aug 2004 Location: DFW Texas Posts: 8,540	Re: Rear end options for a 62 c10 Take the axles out, replace bearings if needed, take the axles to a racing machine shop, have them fill and redrill the bolt pattern to what you need. Make sure they turn down the center of the axle hub a bit __________________ Clyde65 Rebuild of Clyde http://67-72chevytrucks.com/vboard/s...84#post8338184 69 Aristocrat Lo Liner build http://67-72chevytrucks.com/vboard/s...84#post7561684 *support our troops!*

06-05-2019, 11:08 PM	#5
Captainfab 60-66 Nut Join Date: Mar 2007 Location: Coeur d'Alene, Idaho Posts: 23,246	Re: Rear end options for a 62 c10 The Eaton HO32/33 differential that is currently under your truck more than likely has 3.90 gears in it. Depending on what your plans are as far as engine, trans and rear tire size, you might consider changing the entire differential. The '79 12 bolt will work once you weld on the trailing arm mounts and a panhard bar mount, but it will also be 1.5" wider than the Eaton. The increased width may or may not be an issue depending on what rear tires you plan to run. If the width is an issue, look for a '63-'70 truck 12 bolt. They will be the same width as your Eaton and conversion axles are readily available. BTW, I love those wheels. __________________ Power Steering Box Adapter Plates For Sale HERE Power Brake Booster Adapter Brackets For Sale '63-'66 HERE and '67-'72 HERE and '60-'62 HERE and "60-'62 with clutch HERE Rear Disc Brake Brackets For Sale. Impala SS calipers HERE Camaro Calipers HERE D52 Calipers HERE 6 Lug HERE Hydroboost Mounting Plates HERE

06-05-2019, 11:36 PM	#7
slepysal Registered User Join Date: Oct 2006 Location: San Jose NOR*CAL Posts: 3,080	Re: Rear end options for a 62 c10 I used one out of a '67 that had 3.73 as mentioned on 60-62 you have to relocate the trailing arm mounts and swap out the pan hard bar. __________________ 1960 Apache long bed fleet L6 250 Clifford intake 2 bbl carb. Langdon cast headers with dual exhaust and bellflower tips. T-5 5 speed, power steering and power disc brakes. "Over, Around or through it... "

06-06-2019, 12:13 AM	#9
slepysal Registered User Join Date: Oct 2006 Location: San Jose NOR*CAL Posts: 3,080	Re: Rear end options for a 62 c10 no worries... by the way nice looking truck __________________ 1960 Apache long bed fleet L6 250 Clifford intake 2 bbl carb. Langdon cast headers with dual exhaust and bellflower tips. T-5 5 speed, power steering and power disc brakes. "Over, Around or through it... "



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.