Who all has air ride????? Who has rear disk brakes??

[bagged74]

Originally Posted by jkade

Yeah I am hopeing on getting by with just tucking the tire. Its hard to start chopping uo one that is already done I guess. I may have to get a truck and do it up right were I can lay it on the ground.

yeah If i had your blazer I probably wouldnt go choppin it up either..................at least for a while...lol

[jkade]

Originally Posted by bagged74

yeah If i had your blazer I probably wouldnt go choppin it up either..................at least for a while...lol

I wish I would have done this before I got my interior done. It's nothing to chop one up though. My dad is currently chopping up a numbers mathcing 327 350hp, 4 speed, 67 vette factory air car. He ditched every thing and bought a 6.0,t56, art morrison front end, 04 mustang IRS that he is narrowing and going to run like a 295/40/20 on the back of it. People will sure think that he is crazy when this one gets done.

[bagged74]

The nicer truck(or car) you start with, the nicer you have at the end.

[jkade]

Originally Posted by bagged74

The nicer truck(or car) you start with, the nicer you have at the end.

You said it there. I guess that is why I paid so much for a big head start.

[N2TRUX]

Originally Posted by bagged74;

yeah If i had your blazer I probably wouldnt go choppin it up either..................at least for a while...lol

Yes he would... He ain't skeert to cut one up. Fortunately he's able to put them back togther too....

jkade- I know it's not a Blazer, or even a 67-72 truck, but check the pics of my 77 in my sig. That's about as low as you can go and not cut holes in the bed. I could go about another inch lower but then it would not roll when aired out. Tires are 245/40/20 and 295/40/20

[bagged74]

Originally Posted by N2TRUX

Yes he would...

I know....my wife says I ruin everything.

[N2TRUX]

Dude that Blazer in your avatar is sweet. Saw it on layingbody.com. Have you seen any interior shots anywhere?

[bagged74]

Originally Posted by N2TRUX

Dude that Blazer in your avatar is sweet. Saw it on layingbody.com. Have you seen any interior shots anywhere?

no sir I havent. But it is reportedly from your area. Baytown?

[bagged74]

Originally Posted by N2TRUX

Dude that Blazer in your avatar is sweet.

yeah, I think Im in love

[pharcyde05]

Originally Posted by jkade

Anyone with a bagged blazer post a pic, please.

hears a pic of mine i have some more updated ones i will put up for you as soon as i get them downloaded

[pharcyde05]

Originally Posted by jkade

What did you do to the bed for the readend housing? PIC?

i am raising my entire bed floor to clear the notch and raising the wheel tubs to clear the 20"s

[jkade]

Originally Posted by pharcyde05

i am raising my entire bed floor to clear the notch and raising the wheel tubs to clear the 20"s

Were are you going to put your gas filler?

[pharcyde05]

you can see it on the pic i am going to get some new tubeing and its going to go about where it is now i am going to put a billet fuel door in the floor

[jkade]

Originally Posted by pharcyde05

you can see it on the pic i am going to get some new tubeing and its going to go about where it is now i am going to put a billet fuel door in the floor

Pretty good idea. I may have to look into that.

[pharcyde05]

hear is one after the tank was mounted

[pharcyde05]

all the way layed out

[LUV2XCLR8]

Dayum, that thing is sectioned big time

[classicchev]

Yeah got them both, and both are sitting side by side on the shelf!

[gringoloco]

Pharcyde- in your pics it looks like you are laying pinch.

- Did you do this with an 8" step notch only?
- Anything besides spindles/bags in front?
- Any trailing arm/frame interference probs?

-Chris

[smbrouss70]

Originally Posted by N2TRUX

Dude that Blazer in your avatar is sweet. Saw it on layingbody.com. Have you seen any interior shots anywhere?

These are some pics I took of it at the show in Lake Charles, LA. I could have sworn that I had gotten some shots of the interior. It was a basic interior though, no side panels, just buckets and a bench.

Sorry for the hijack

[LUV2XCLR8]

I like almost everything about that, BUT ..................... I'd have to change a few things.
Don't get me wrong, it's sweeeeeeeeeeeeeeeeeet as it can be, just have different tastes.

[bagged74]

Originally Posted by gringoloco

Pharcyde- in your pics it looks like you are laying pinch.

- Did you do this with an 8" step notch only?
- Any trailing arm/frame interference probs?

-Chris

There will be interference problems with the trailing arms, but nothing that cant be overcome. Mine were hitting the frame even with my 6.5" notch

[gringoloco]

Originally Posted by bagged74

There will be interference problems with the trailing arms, but nothing that cant be overcome. Mine were hitting the frame even with my 6.5" notch

Do you think moving the perches on the axle closer to center would give enough clearance?

[Rydn2L0w]

Originally Posted by bagged74

There will be interference problems with the trailing arms, but nothing that cant be overcome. Mine were hitting the frame even with my 6.5" notch

Did you section the engine x member? or Z the frame? to get it it to lay pinchweld.

[bagged74]

Originally Posted by Rydn2L0w

Did you section the engine x member? or Z the frame? to get it it to lay pinchweld.

Mine does not lay pinchweld. Its a couple of inches from it.