1/2T vs. 3/4T 2wd front spindles and hubs. - The 1947 - Present Chevrolet & GMC Truck Message Board Network

andyt · 01-12-2007, 01:34 PM

Hey guys,
Does anybody know if 3/4T 8 lug hubs will fit on 1/2T spindles?

I am putting a 8 lug Dana 60 in the rear of my C-10 and I want to make the front 8 lug also. Thanks for any info.

AndyT

andyt · 01-16-2007, 08:10 AM

Does any body have a idea on this?
Thanks for the help.
AndyT

crazy longhorn · 01-16-2007, 12:35 PM

You will need to replace the lower a arms(due to ball joint size), upper/lower balljoints,add the 3/4 ton spindles, & all the steering linkage(tierod ends/sleeves,& the centerlink). the 3/4 ton ball joints will bolt into the upper arms. best of luck,

L

andyt · 01-18-2007, 04:03 PM

One more question. Well the same caliper work or do I need 3/4T calipers?
Thanks
AndyT

01-12-2007, 01:34 PM	#1
andyt Registered User Join Date: Nov 2006 Location: Winder, GA Posts: 18	1/2T vs. 3/4T 2wd front spindles and hubs. Hey guys, Does anybody know if 3/4T 8 lug hubs will fit on 1/2T spindles? I am putting a 8 lug Dana 60 in the rear of my C-10 and I want to make the front 8 lug also. Thanks for any info. AndyT __________________ '72 Custom Deluxe C-10 Allis Chamlers 4 cyl. Turbo Diesel engine, Ford granny low 4 spd. trans. '91 Dodge D250 Cummins Diesel Antique Pulling Tractors: 1956 Allis WD45 Diesel 1960 Allis D17 Diesel 196? Allis D21 Diesel

01-16-2007, 08:10 AM	#2
andyt Registered User Join Date: Nov 2006 Location: Winder, GA Posts: 18	Re: 1/2T vs. 3/4T 2wd front spindles and hubs. Does any body have a idea on this? Thanks for the help. AndyT __________________ '72 Custom Deluxe C-10 Allis Chamlers 4 cyl. Turbo Diesel engine, Ford granny low 4 spd. trans. '91 Dodge D250 Cummins Diesel Antique Pulling Tractors: 1956 Allis WD45 Diesel 1960 Allis D17 Diesel 196? Allis D21 Diesel

01-16-2007, 12:35 PM	#3
crazy longhorn Fabricate till you "puke" Join Date: Jun 2002 Location: Ill Posts: 9,403	Re: 1/2T vs. 3/4T 2wd front spindles and hubs. You will need to replace the lower a arms(due to ball joint size), upper/lower balljoints,add the 3/4 ton spindles, & all the steering linkage(tierod ends/sleeves,& the centerlink). the 3/4 ton ball joints will bolt into the upper arms. best of luck, L __________________ 69 longhorn,4" chop,3/5 drop, 1/2 ton suspension/disc brakes,1 1/2" body drop,steel tilt clip, 5.3/Edelbrock rpm intake/600 carb, Hooker streetrod shorties,2 1/2" exhaust/ H pipe/50's Flows , 6 spd Richmond trans,12 bolt/ 3.40 gears....

01-18-2007, 04:03 PM	#4
andyt Registered User Join Date: Nov 2006 Location: Winder, GA Posts: 18	Re: 1/2T vs. 3/4T 2wd front spindles and hubs. One more question. Well the same caliper work or do I need 3/4T calipers? Thanks AndyT __________________ '72 Custom Deluxe C-10 Allis Chamlers 4 cyl. Turbo Diesel engine, Ford granny low 4 spd. trans. '91 Dodge D250 Cummins Diesel Antique Pulling Tractors: 1956 Allis WD45 Diesel 1960 Allis D17 Diesel 196? Allis D21 Diesel



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.