Register or Log In To remove these advertisements. |
|
|
|
Thread Tools | Display Modes |
|
03-25-2012, 11:19 PM | #1 |
Senior Member
Join Date: May 2010
Location: Wisconsin & Arizona
Posts: 4,839
|
Re: Original Bucket seats installation????
I don't have my cab here to confirm this, but it appears that the dimples refered to are visible in a couple of your pictures outboard of the seat brackets. Looks like 1/2"-3/4" out from the existing holes. This is consistent with where my original buckets were mounted from the factory.
|
03-25-2012, 11:39 PM | #2 | |
Still Learning
Join Date: Jul 2009
Location: Central Oklahoma
Posts: 10,108
|
Re: Original Bucket seats installation????
Quote:
These look like dimples in the picture here:
__________________
Mike "69 Short Wide" My Project 86 Silverado Landen's Project Instagram: @mcbassin My Website C/10 Club Oklahoma Facebook Group Last edited by mcbassin; 03-25-2012 at 11:45 PM. |
|
03-26-2012, 12:08 AM | #3 |
Senior Member
Join Date: May 2010
Location: Wisconsin & Arizona
Posts: 4,839
|
Re: Original Bucket seats installation????
Those are the ones I was referring to. I don't have any pictures that would help, and the truck is currently disassembled and 2000 miles away. If you can wait about 3 weeks I can get pics. However, I estimate the seats are about 3/8"-1/2" away from the console. I have some shots with the seats installed but from a 45 degree angle... not much help.
|
03-26-2012, 12:20 AM | #4 | |
Still Learning
Join Date: Jul 2009
Location: Central Oklahoma
Posts: 10,108
|
Re: Original Bucket seats installation????
Quote:
|
|
03-26-2012, 12:56 AM | #5 |
Senior Member
Join Date: May 2010
Location: Wisconsin & Arizona
Posts: 4,839
|
Re: Original Bucket seats installation????
I found this old thread http://67-72chevytrucks.com/vboard/s...d.php?t=352079
Perhaps post 8 will help. I'm still searching for others. Jim |
03-26-2012, 01:37 AM | #6 |
Senior Member
Join Date: May 2010
Location: Wisconsin & Arizona
Posts: 4,839
|
Re: Original Bucket seats installation????
Here's another thread http://67-72chevytrucks.com/vboard/s...d.php?t=367549
|
03-26-2012, 04:53 AM | #7 |
Always on the hunt...
Join Date: Sep 2006
Location: Portland, OR.
Posts: 5,537
|
Re: Original Bucket seats installation????
Hi Mike, I have owned decent share of these trucks over the years and done a few 69-72 truck bench to bucket conversions in them years and have not came across any floor pans having the dimples already in place for drilling the bucket seat mounting bolt holes, maybe that was a regional/plant type of deal. I'll give this a shot to the best of my knowledge, when using the 69-72 truck bucket bracket setups and when going into an original bench seat truck cab, there is only one hole of the eight in the bench cab floor pan that's already in the correct place and that you are going to use when bolting the bucket mounts in. The one bolt hole (only one in correct location) that you should use is the RH fwd. most outer bolt hole, so it would be the pass. side fixed mounted bucket fwd. RH bolt, you will need to drill the other eleven mounting bolt holes. I have had these pictures of an OE option #A50 bucket seat floor pan that were taken for another member and then stuck away in a saved folder, not sure if they will help you dimensionally as they don't have any measurements but the pics do highlight all twelve of the bucket seat bracket mounting bolt holes and they also show how the factory used pan head filler screws to plug the other bench seat mounting bolt holes. The bottom view pictures highlight the factory added bucket seat cab only floor cross support & extra bracing. Hope this post and pics can get ya headed in the right direction, Mel.
|
03-26-2012, 04:57 AM | #8 |
Always on the hunt...
Join Date: Sep 2006
Location: Portland, OR.
Posts: 5,537
|
Re: Original Bucket seats installation????
Last five B/S floor pan pics...
|
03-26-2012, 08:26 AM | #9 | |
Still Learning
Join Date: Jul 2009
Location: Central Oklahoma
Posts: 10,108
|
Re: Original Bucket seats installation????
Quote:
Thank you so much. This is exactly the information I was looking for. What you are saying is my pass. side holes I already drilled are in the right position. I only used the outer front hole and then marked the other three with it bolted down in that one hole. I'm assuming the driver side mount setup is wider becaus the outer holes need to go outward about 3/4-1" in your picture. Do you happen to know what the gap was at the center console between the seats on both sides? Also, when you installed these buckets on bench trucks did you fabricate that front brace that runs across the bottom of the rib at the front mounting position? thanks for the help. |
|
03-27-2012, 01:15 PM | #10 | |
Always on the hunt...
Join Date: Sep 2006
Location: Portland, OR.
Posts: 5,537
|
Re: Original Bucket seats installation????
Quote:
|
|
Bookmarks |
|
|